Power Generation Amplification and Stack Toughening via Compliant Layer Interdigitation

2018 ◽  
Author(s):  
Ember D. Krech ◽  
Ronald M. Barrett ◽  
Eileen S. Cadel ◽  
Elizabeth A. Friis
Keyword(s):  
Power Generation ◽  
Layer Thickness ◽  
Low Frequency ◽  
Small Deformation ◽  
Lateral Strain ◽  
Shear Lag ◽  
Low Frequencies ◽  
Mechanics Model ◽  
Resonance Frequencies ◽  
Compliant Layer

Energy harvesting from low frequency cyclic motion is possible in a variety of applications, but generating power with piezoelectric stacks at low, off-resonance frequencies is challenging. In this study, Compliant Layer Adaptive Composite Stacks (CLACS) were investigated as a toughened piezoelectric generator to increase efficiency at low frequencies and match the compliance of many commercial devices. CLACS were manufactured with PZT discs, interdigitated epoxy layers of varying thicknesses, and encapsulated in epoxy. Energy production of each CLACS type as a function of compliant layer thickness was characterized. Power amplification of CLACS was modeled assuming discs remain planar, volume of epoxy was conserved, and total epoxy deformations were small. Shear lag theory demonstrated increases in positive in-plane strains induced by external through-thickness compression. This amplified sensitivity of the entire stack to through-thickness compressions, substantially increases power generation capability. Experimental data showed that increases in compliant layer thickness resulted in increased power generation in all loading conditions. The shear lag structural mechanics model showed good correlation with theoretical predictions, assuming small deformation of the compliant layer. In addition to reducing composite stiffness, the CLACS generated 61% more power than conventional stack actuators with the same PZT volume via lateral strain amplification effects.

Bending Vibrations of the Femur and the Oscillatory Behavior of a Cemented Femoral Hip Endoprosthesis

2000 ◽  
Vol 122 (4) ◽  
pp. 416-422
Author(s):  
M. Thomsen ◽  
A. Go¨rtz ◽  
U. V. Na¨gerl ◽  
D. Kubein-Meesenburg ◽  
W. Go¨rtz ◽  
...  
Keyword(s):  
Degrees Of Freedom ◽  
Low Frequency ◽  
Oscillatory Behavior ◽  
Measuring System ◽  
Frequency Range ◽  
Entire Frequency Range ◽  
Bending Vibrations ◽  
Low Frequencies ◽  
Hip Endoprosthesis ◽  
Resonance Frequencies

The paper presents a novel method for recording amplitude and phase of 6D-vibrations of a spatial pendulum over a wide frequency range (10 Hz up to 20 kHz). The six degrees of freedom of the pendulum mass were monitored by three electrodynamic stereo pickups. At rest, the tips of the needles and the pendulum’s center of mass defined the reference system with respect to which the oscillations of the mass were recorded in terms of their amplitudes and phases. Its small dimensions, constant transfer characteristics, linearity, high dynamics, and virtual lack of reaction onto the moving system over the entire frequency range provided the advantages of the measuring system. This method was used to analyze the spatial 6D-vibrations of the head of a cemented femoral hip endoprosthesis when the femur was stimulated to bending vibrations. The head of the prosthesis carried out axial rotational vibrations at every frequency used to stimulate the femur. The amplitudes of the axial rotations of the cortical bone were small in comparison to the ones of the prosthesis head, indicating that axial rotational vibrations following femur bending vibrations mainly stressed the spongiosa and the cement layer. This was observed over the entire frequency range, including at the low frequencies relevant for gait. Over the low-frequency range, as well as at some of the higher resonance frequencies, stationary instantaneous helical axes characterized the vibrations. The measurements suggest the mechanism that the interface “implant-bone” may already be stressed by axial torsional loads when the femur is loaded by bending impacts that are known to occur during walking. [S0148-0731(00)01604-6]

Optimization of metamaterials with complex neck shapes for aircraft cabin noise improvement

2021 ◽  
Vol 263 (2) ◽  
pp. 3963-3974
Author(s):  
Tenon Charly Kone ◽  
Sebastian Ghinet ◽  
Raymond Panneton ◽  
Anant Grewa
Keyword(s):  
Transmission Loss ◽  
Low Frequency ◽  
Optimization Method ◽  
Frequency Noise ◽  
Low Frequencies ◽  
Helmholtz Resonators ◽  
Cabin Noise ◽  
Resonance Frequencies ◽  
In Series ◽  
Small Form Factor

More frequently, recent low-frequency noise control techniques commonly implemented in aerospace and ground transportation as well as in building applications are based on acoustic metamaterial concepts. The technologies proposed in the literature, using layered porous materials with embedded Helmholtz resonators (HR), exhibited considerable potential when tuned at tonal, multi-tonal or narrow frequency bands. Our recent investigations have shown that the acoustical performance of these metamaterials can be further improved by the use of resonators with complex shaped necks. These necks can be designed and optimized to minimize the HR resonance frequencies (small form factor) and maximize the sound transmission loss (STL) performance. This paper presents the developed design optimization method for HRs with complex neck shapes recessed within the HR cavity. The HRs were embedded in a layer of porous material. The implemented approach was based on the transfer matrix methods (TMM) in series and in parallel coupled to a multi-objective optimization. Complex optimum neck shapes were obtained allowing for a shift towards the low frequencies of the resonator resonance with a good STL performance. Moreover the STL calculated using the TMM approach were observed to be in excellent agreement with the finite element method numerical results.

Multi-tonal low frequency noise control using Helmholtz resonators with complex cavity designs for aircraft cabin noise improvement

2021 ◽  
Vol 263 (2) ◽  
pp. 3975-3986
Author(s):  
Tenon Charly Kone ◽  
Sebastian Ghinet ◽  
Raymond Panneton ◽  
Thomas Dupont ◽  
Anant Grewal
Keyword(s):  
Noise Control ◽  
Transmission Loss ◽  
Low Frequency ◽  
Helmholtz Resonator ◽  
Sound Insulation ◽  
Frequency Noise ◽  
Low Frequency Noise ◽  
Low Frequencies ◽  
Helmholtz Resonators ◽  
Resonance Frequencies

The noise control at multiple tonal frequencies simultaneously, in the low frequency range, is a challenge for aerospace, ground transportation and building industries. In the past few decades, various low frequency noise control solutions based on acoustic metamaterial designs have been presented in the literature. These solutions showed promising performance and are considered a better alternative to conventional sound insulation materials. In the present investigation, it was noticed that subdividing the cavity of a Helmholtz resonator allowed the control of multi-tonal noise at several resonance frequencies simultaneously and a shift of the resonance peaks towards the low frequencies. This paper proposes concepts of Helmholtz resonators with subdivided cavities to improve the sound transmission loss (STL) performance and simultaneously control the noise at several tonal frequencies. HRs with cylindrical shaped cavities were embedded in a layer of porous material. The STL of the metamaterial noise insulation configuration was predicted using serial and parallel assemblies of transfer matrices (TMM) incorporating a thermo-viscous-acoustic approach to accurately account for the viscous and thermal losses of acoustic wave propagation within the metamaterial. The STL calculated using the proposed TMM approach were observed to be in excellent agreement with the finite element method (FEM) numerical results.

scholarly journals Vibration of a stiffened pipe filled with a bubbly liquid: analysis of resonance frequencies in function of bubble fraction

2021 ◽  
Vol 263 (5) ◽  
pp. 1008-1018
Author(s):  
Sanae Serbout ◽  
Laurent Maxit ◽  
Frédéric Michel
Keyword(s):  
Cylindrical Shell ◽  
Volume Fraction ◽  
Low Frequency ◽  
Acoustic Properties ◽  
Bubbly Liquid ◽  
Low Frequencies ◽  
Stiffened Cylindrical Shell ◽  
Resonance Frequencies ◽  
Gas Volume Fraction ◽  
Gas Volume

The characterization of the presence of bubbles in industrial fluid circuits may be extremely important for many safety issuses. It is well known that the acoustic properties of liquids can be drastically modified by a small amount of gaz content in the liquid. At sufficiently low frequencies, the speed of sound depends primarily on the gas volume fraction. The variation of the gas fraction may then induce some variations in the vibroacoustic behavior of the pipe transporting the liquid. Analysis of the pipe vibrations can then help in the monitoring of the bubble presence. In such a context, the aim of this study is to show how the the presence of bubbles in the liquid could affect the resonance frequencies of the pipe. A numerical vibroacoustical model has been developed to predict the vibroacoustical behavior of a stiffened cylindrical shell filled with a bubbly liquid exhibiting low frequency resonances. The model, experimentally verified with a well-characterized bubbly liquid, is then used to analyse the frequency shifts of the shell resonances in function of the bubble. Keywords : pipe, heavy fluid, numerical modelling, circumferential admittance approach, cylindrical shell, resonance frequency, void fraction

scholarly journals A Multi-Mode Broadband Vibration Energy Harvester Composed of Symmetrically Distributed U-Shaped Cantilever Beams

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 203
Author(s):  
Xiaohua Huang ◽  
Cheng Zhang ◽  
Keren Dai
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Experimental Results ◽  
Vibration Energy ◽  
Cantilever Beams ◽  
Resonant Frequencies ◽  
Promising Alternative ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Resonance Frequencies

Using the piezoelectric effect to harvest energy from surrounding vibrations is a promising alternative solution for powering small electronic devices such as wireless sensors and portable devices. A conventional piezoelectric energy harvester (PEH) can only efficiently collect energy within a small range around the resonance frequency. To realize broadband vibration energy harvesting, the idea of multiple-degrees-of-freedom (DOF) PEH to realize multiple resonant frequencies within a certain range has been recently proposed and some preliminary research has validated its feasibility. Therefore, this paper proposed a multi-DOF wideband PEH based on the frequency interval shortening mechanism to realize five resonance frequencies close enough to each other. The PEH consists of five tip masses, two U-shaped cantilever beams and a straight beam, and tuning of the resonance frequencies is realized by specific parameter design. The electrical characteristics of the PEH are analyzed by simulation and experiment, validating that the PEH can effectively expand the operating bandwidth and collect vibration energy in the low frequency. Experimental results show that the PEH has five low-frequency resonant frequencies, which are 13, 15, 18, 21 and 24 Hz; under the action of 0.5 g acceleration, the maximum output power is 52.2, 49.4, 61.3, 39.2 and 32.1 μW, respectively. In view of the difference between the simulation and the experimental results, this paper conducted an error analysis and revealed that the material parameters and parasitic capacitance are important factors that affect the simulation results. Based on the analysis, the simulation is improved for better agreement with experiments.

scholarly journals Earless toads sense low frequencies but miss the high notes

2017 ◽  
Vol 284 (1864) ◽  
pp. 20171670 ◽  
Author(s):  
Molly C. Womack ◽  
Jakob Christensen-Dalsgaard ◽  
Luis A. Coloma ◽  
Juan C. Chaparro ◽  
Kim L. Hoke
Keyword(s):  
High Frequency ◽  
Species Differences ◽  
Low Frequency ◽  
Auditory Brainstem ◽  
Low Frequencies ◽  
Hearing Sensitivity ◽  
Sensory Pathways ◽  
Airborne Sound ◽  
Vibrational Sensitivity ◽  
Species Specific

Sensory losses or reductions are frequently attributed to relaxed selection. However, anuran species have lost tympanic middle ears many times, despite anurans' use of acoustic communication and the benefit of middle ears for hearing airborne sound. Here we determine whether pre-existing alternative sensory pathways enable anurans lacking tympanic middle ears (termed earless anurans) to hear airborne sound as well as eared species or to better sense vibrations in the environment. We used auditory brainstem recordings to compare hearing and vibrational sensitivity among 10 species (six eared, four earless) within the Neotropical true toad family (Bufonidae). We found that species lacking middle ears are less sensitive to high-frequency sounds, however, low-frequency hearing and vibrational sensitivity are equivalent between eared and earless species. Furthermore, extratympanic hearing sensitivity varies among earless species, highlighting potential species differences in extratympanic hearing mechanisms. We argue that ancestral bufonids may have sufficient extratympanic hearing and vibrational sensitivity such that earless lineages tolerated the loss of high frequency hearing sensitivity by adopting species-specific behavioural strategies to detect conspecifics, predators and prey.

A waveform inversion technique for measuring elastic wave attenuation in cylindrical bars

Geophysics ◽  
1992 ◽  
Vol 57 (6) ◽  
pp. 854-859 ◽  
Author(s):  
Xiao Ming Tang
Keyword(s):  
Elastic Wave ◽  
Wave Attenuation ◽  
Waveform Inversion ◽  
Finite Size ◽  
Low Frequency ◽  
Frequency Range ◽  
Multiple Reflections ◽  
Low Frequencies ◽  
The Time Domain ◽  
Attenuation Values

A new technique for measuring elastic wave attenuation in the frequency range of 10–150 kHz consists of measuring low‐frequency waveforms using two cylindrical bars of the same material but of different lengths. The attenuation is obtained through two steps. In the first, the waveform measured within the shorter bar is propagated to the length of the longer bar, and the distortion of the waveform due to the dispersion effect of the cylindrical waveguide is compensated. The second step is the inversion for the attenuation or Q of the bar material by minimizing the difference between the waveform propagated from the shorter bar and the waveform measured within the longer bar. The waveform inversion is performed in the time domain, and the waveforms can be appropriately truncated to avoid multiple reflections due to the finite size of the (shorter) sample, allowing attenuation to be measured at long wavelengths or low frequencies. The frequency range in which this technique operates fills the gap between the resonant bar measurement (∼10 kHz) and ultrasonic measurement (∼100–1000 kHz). By using the technique, attenuation values in a PVC (a highly attenuative) material and in Sierra White granite were measured in the frequency range of 40–140 kHz. The obtained attenuation values for the two materials are found to be reliable and consistent.

Methods to isolate retrograde and prograde Rayleigh-wave signals

2019 ◽  
Vol 219 (2) ◽  
pp. 975-994 ◽  
Author(s):  
Gabriel Gribler ◽  
T Dylan Mikesell
Keyword(s):  
Rayleigh Wave ◽  
Time Domain ◽  
Fundamental Mode ◽  
Poisson Ratio ◽  
Low Frequency ◽  
Wave Dispersion ◽  
Low Frequencies ◽  
Retrograde Motion ◽  
Mode Identification ◽  
Time Frequency

SUMMARY Estimating shear wave velocity with depth from Rayleigh-wave dispersion data is limited by the accuracy of fundamental and higher mode identification and characterization. In many cases, the fundamental mode signal propagates exclusively in retrograde motion, while higher modes propagate in prograde motion. It has previously been shown that differences in particle motion can be identified with multicomponent recordings and used to separate prograde from retrograde signals. Here we explore the domain of existence of prograde motion of the fundamental mode, arising from a combination of two conditions: (1) a shallow, high-impedance contrast and (2) a high Poisson ratio material. We present solutions to isolate fundamental and higher mode signals using multicomponent recordings. Previously, a time-domain polarity mute was used with limited success due to the overlap in the time domain of fundamental and higher mode signals at low frequencies. We present several new approaches to overcome this low-frequency obstacle, all of which utilize the different particle motions of retrograde and prograde signals. First, the Hilbert transform is used to phase shift one component by 90° prior to summation or subtraction of the other component. This enhances either retrograde or prograde motion and can increase the mode amplitude. Secondly, we present a new time–frequency domain polarity mute to separate retrograde and prograde signals. We demonstrate these methods with synthetic and field data to highlight the improvements to dispersion images and the resulting dispersion curve extraction.

Upgraded Railway Front Searchlight Design Plastic Deformations by its Vibrations with Resonance Frequencies

2016 ◽  
Vol 684 ◽  
pp. 111-119 ◽  
Author(s):  
Stanislav Rafaelevich Abulkhanov ◽  
Dmitrii Sergeevich Goryainov
Keyword(s):  
Natural Frequencies ◽  
Ansys Software ◽  
Software Environment ◽  
Low Frequencies ◽  
Plastic Deformations ◽  
Vibration Resistance ◽  
First Case ◽  
Resonance Frequencies ◽  
The One ◽  
Electric Lamp

Natural frequencies of the four upgraded front searchlight designs were received in ANSYS software environment. In the first case serial front searchlight incandescent electric lamp was replaced by a LED group which was mounted on the one-piece cylinder backing. The second front searchlight design had the backing which was upgraded by a radial ribs and concentric rigidity ferrules. Analyze of the backing deformation character by vibrations with the natural frequencies established a number of design solutions which make it possible to raise front searchlight vibration resistance. By the front searchlight model were established that the natural frequencies of the searchlight with the one-piece backing appertain to the whole range of the train vibrations. Natural frequencies of the backing with perforation, rigidity ferrules, and radial ribs appertain to the low frequencies of the railway locomotive vibrations spectrum. On basis of devised methodology of analyze of the deformation and natural frequencies of the surface carrying a LED group the vibration-proof searchlight design was introduced and researched.

Optimally Sensitive and Efficient Compact Loudspeakers for Low Audio Frequencies

2007 ◽  
Vol 38 (7) ◽  
pp. 11-17
Author(s):  
Ronald M. Aarts
Keyword(s):  
Optimality Criterion ◽  
Low Frequency ◽  
Audio Signal ◽  
Design Procedure ◽  
Frequency Range ◽  
Force Factor ◽  
Low Frequencies ◽  
Limited Frequency ◽  
The Cost ◽  
Higher Sensitivity

Conventionally, the ultimate goal in loudspeaker design has been to obtain a flat frequency response over a specified frequency range. This can be achieved by carefully selecting the main loudspeaker parameters such as the enclosure volume, the cone diameter, the moving mass and the very crucial “force factor”. For loudspeakers in small cabinets the results of this design procedure appear to be quite inefficient, especially at low frequencies. This paper describes a new solution to this problem. It consists of the combination of a highly non-linear preprocessing of the audio signal and the use of a so called low-force-factor loudspeaker. This combination yields a strongly increased efficiency, at least over a limited frequency range, at the cost of a somewhat altered sound quality. An analytically tractable optimality criterion has been defined and has been verified by the design of an experimental loudspeaker. This has a much higher efficiency and a higher sensitivity than current low-frequency loudspeakers, while its cabinet can be much smaller.

Sign in / Sign up

Export Citation Format

Share Document