Efficiency optimization of 3-µm Q-switched lasers based on Er-doped crystalline materials

2020 ◽  
Author(s):  
Nikolay E. Ter-Gabrielyan ◽  
Viktor Fromzel
Keyword(s):  
Crystalline Materials ◽  
Efficiency Optimization ◽  
Er Doped

Resolution, Contrast and Interpretation of HVEM Images of Crystals

1973 ◽  
Vol 31 ◽  
pp. 228-229
Author(s):  
L. E. Thomas ◽  
J. S. Lally ◽  
R. M. Fisher
Keyword(s):  
High Voltage ◽  
Chromatic Aberration ◽  
Crystalline Materials ◽  
Resolution Parameter ◽  
Instrument Resolution ◽  
Imaging Conditions ◽  
Beam Excitation ◽  
Optimum Imaging

In addition to improved penetration at high voltage, the characteristics of HVEM images of crystalline materials are changed markedly as a result of many-beam excitation effects. This leads to changes in optimum imaging conditions for dislocations, planar faults, precipitates and other features.Resolution - Because of longer focal lengths and correspondingly larger aberrations, the usual instrument resolution parameter, CS174 λ 374 changes by only a factor of 2 from 100 kV to 1 MV. Since 90% of this change occurs below 500 kV any improvement in “classical” resolution in the MVEM is insignificant. However, as is widely recognized, an improvement in resolution for “thick” specimens (i.e. more than 1000 Å) due to reduced chromatic aberration is very large.

TEM studies of amorphization processes and amorphous structures

1988 ◽  
Vol 46 ◽  
pp. 448-449
Author(s):  
T. E. Mitchell ◽  
R. B. Schwarz
Keyword(s):  
Amorphous Materials ◽  
Fission Products ◽  
Rapid Quenching ◽  
Surface Films ◽  
List Type ◽  
Oxide Glasses ◽  
Crystalline Materials ◽  
Amorphous Structures ◽  
Amorphous Surface ◽  
Interfacial Films

Traditional oxide glasses occur naturally as obsidian and can be made easily by suitable cooling histories. In the past 30 years, a variety of techniques have been discovered which amorphize normally crystalline materials such as metals. These include [1-3]:Rapid quenching from the vapor phase.Rapid quenching from the liquid phase.Electrodeposition of certain alloys, e.g. Fe-P.Oxidation of crystals to produce amorphous surface oxide layers.Interdiffusion of two pure crystalline metals.Hydrogen-induced vitrification of an intermetal1ic.Mechanical alloying and ball-milling of intermetal lie compounds.Irradiation processes of all kinds using ions, electrons, neutrons, and fission products.We offer here some general comments on the use of TEM to study these materials and give some particular examples of such studies.Thin specimens can be prepared from bulk homogeneous materials in the usual way. Most often, however, amorphous materials are in the form of surface films or interfacial films with different chemistry from the substrates.

Possible applications of fraunhofer holography in high resolution electron microscopy

1978 ◽  
Vol 36 (1) ◽  
pp. 222-223 ◽  
Author(s):  
N. Bonnet ◽  
M. Troyon ◽  
P. Gallion
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Transfer Function ◽  
Radiation Damage ◽  
High Resolution Electron Microscopy ◽  
Far Field ◽  
Field Region ◽  
Crystalline Materials ◽  
Resolution Electron ◽  
The Ideal

Two main problems in high resolution electron microscopy are first, the existence of gaps in the transfer function, and then the difficulty to find complex amplitude of the diffracted wawe from registered intensity. The solution of this second problem is in most cases only intended by the realization of several micrographs in different conditions (defocusing distance, illuminating angle, complementary objective apertures…) which can lead to severe problems of contamination or radiation damage for certain specimens.Fraunhofer holography can in principle solve both problems stated above (1,2). The microscope objective is strongly defocused (far-field region) so that the two diffracted beams do not interfere. The ideal transfer function after reconstruction is then unity and the twin image do not overlap on the reconstructed one.We show some applications of the method and results of preliminary tests.Possible application to the study of cavitiesSmall voids (or gas-filled bubbles) created by irradiation in crystalline materials can be observed near the Scherzer focus, but it is then difficult to extract other informations than the approximated size.

Scanning Transmission Microscopy Applied to Thick Specimen

1972 ◽  
Vol 30 ◽  
pp. 452-453
Author(s):  
H. Koike ◽  
T. Matsuo ◽  
K. Ueno ◽  
M. Suzuki
Keyword(s):  
Psoas Muscle ◽  
Image Intensifier ◽  
Chromatic Aberration ◽  
Image Contrast ◽  
Transmission Microscopy ◽  
Crystalline Materials ◽  
Thick Specimen ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Electron Microscope Image

Since the identification of single atoms was achieved by Crewe et al, scanning transmission microscopy has been put into pratical use. Recently they applied this method to the quantitative mass analysis of DNA.As pointed out previously the chromatic aberration which decreases the image contrast and quality, does not affect a scanning transmission image as it does a conventional transmission electron microscope image. Thus, the STEM method is advantageous for thick specimen. Further this method employs a high sensitive photomultiplier tube which also functions as an image intensifier. This detection method is effective for the observation of living specimens or easily damaged specimens. In this respect the scanning transmission microscope with high accelerating voltage is necessary.Since Uyeda's experiments of crystalline materials, many workers have been discussed how thick specimens can be observed by CTEM. With biological specimens, R. Szirmae reported on the decrease in the image contrast of rabbit psoas muscle sections at various accelerating voltages and specimen thicknesses.

Voltage and Orientation Dependence of Characteristic X-Ray Production in Thin Crystals

1985 ◽  
Vol 43 ◽  
pp. 414-415
Author(s):  
G. Thomas ◽  
K. M. Krishnan ◽  
Y. Yokota ◽  
H. Hashimoto
Keyword(s):  
Standing Wave ◽  
Incident Beam ◽  
Orientation Dependence ◽  
Incident Plane Wave ◽  
Crystalline Materials ◽  
X Ray ◽  
Incident Plane ◽  
Crystal Unit Cell ◽  
Beam Orientation ◽  
Acceleration Voltage

For crystalline materials, an incident plane wave of electrons under conditions of strong dynamical scattering sets up a standing wave within the crystal. The intensity modulations of this standing wave within the crystal unit cell are a function of the incident beam orientation and the acceleration voltage. As the scattering events (such as inner shell excitations) that lead to characteristic x-ray production are highly localized, the x-ray intensities in turn, are strongly determined by the orientation and the acceleration voltage. For a given acceleration voltage or wavelength of the incident wave, it has been shown that this orientation dependence of the characteristic x-ray emission, termed the “Borrmann effect”, can also be used as a probe for determining specific site occupations of elemental additions in single crystals.

Thickness Measurement in the AEM by Macintosh-Based Analysis of Two-Beam Convergent Beam Patterns

1990 ◽  
Vol 48 (2) ◽  
pp. 504-505
Author(s):  
John F. Mansfield ◽  
Douglas C. Crawford
Keyword(s):  
Electron Microscope ◽  
Video Camera ◽  
Thickness Measurement ◽  
Specimen Thickness ◽  
Crystalline Materials ◽  
Beam Dynamic ◽  
Line Measurement ◽  
On Line ◽  
Image Position ◽  
Convergent Beam

A method has been developed that allows on-line measurement of the thickness of crystalline materials in the analytical electron microscope. Two-beam convergent beam electron diffraction (CBED) patterns are digitized from a JEOL 2000FX electron microscope into an Apple Macintosh II microcomputer via a Gatan #673 CCD Video Camera and an Imaging Systems Technology Video 1000 frame-capture board. It is necessary to know the lattice parameters of the sample since measurements are made of the spacing of the diffraction discs in order to calibrate the pattern. The sample thickness is calculated from measurements of the spacings of the fringes that are seen in the diffraction discs. This technique was pioneered by Kelly et al, who used the two-beam dynamic theory of MacGillavry relate the deviation parameter (Si) of the ith fringe from the exact Bragg condition to the specimen thickness (t) with the equation:Where ξg, is the extinction distance for that reflection and ni is an integer.

Automatic analysis of Kikuchi diffraction patterns

1994 ◽  
Vol 52 ◽  
pp. 900-901
Author(s):  
H. Weiland ◽  
D. P. Field
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
Spatial Resolution ◽  
Relevant Information ◽  
Crystalline Materials ◽  
Large Size ◽  
Transmission Electron ◽  
New Type ◽  
Diffraction Patterns ◽  
Orientation Determination

Recent advances in the automatic indexing of backscatter Kikuchi diffraction patterns on the scanning electron microscope (SEM) has resulted in the development of a new type of microscopy. The ability to obtain statistically relevant information on the spatial distribution of crystallite orientations is giving rise to new insight into polycrystalline microstructures and their relation to materials properties. A limitation of the technique in the SEM is that the spatial resolution of the measurement is restricted by the relatively large size of the electron beam in relation to various microstructural features. Typically the spatial resolution in the SEM is limited to about half a micron or greater. Heavily worked structures exhibit microstructural features much finer than this and require resolution on the order of nanometers for accurate characterization. Transmission electron microscope (TEM) techniques offer sufficient resolution to investigate heavily worked crystalline materials.Crystal lattice orientation determination from Kikuchi diffraction patterns in the TEM (Figure 1) requires knowledge of the relative positions of at least three non-parallel Kikuchi line pairs in relation to the crystallite and the electron beam.

On resolving fine periodic microstructures in the optical microscope

1989 ◽  
Vol 47 ◽  
pp. 364-365
Author(s):  
W.S. Putnam ◽  
C. Viney
Keyword(s):  
Liquid Crystalline ◽  
Numerical Aperture ◽  
Polarized Light ◽  
Normal Incidence ◽  
Optical Microscope ◽  
Angle Of Incidence ◽  
Resolution Limit ◽  
Crystalline Materials ◽  
Periodic Microstructures ◽  
Liquid Crystalline Materials

Many sheared liquid crystalline materials (fibers, films and moldings) exhibit a fine banded microstructure when observed in the polarized light microscope. In some cases, for example Kevlar® fiber, the periodicity is close to the resolution limit of even the highest numerical aperture objectives. The periodic microstructure reflects a non-uniform alignment of the constituent molecules, and consequently is an indication that the mechanical properties will be less than optimal. Thus it is necessary to obtain quality micrographs for characterization, which in turn requires that fine detail should contribute significantly to image formation.It is textbook knowledge that the resolution achievable with a given microscope objective (numerical aperture NA) and a given wavelength of light (λ) increases as the angle of incidence of light at the specimen surface is increased. Stated in terms of the Abbe resolution criterion, resolution improves from λ/NA to λ/2NA with increasing departure from normal incidence.

A Structural Model for a Quasi-Crystalline Material Derived from TEM

1990 ◽  
Vol 48 (1) ◽  
pp. 48-49
Author(s):  
Jan-Olov Bovin ◽  
Osamu Terasaki ◽  
Jan-Olle Malm ◽  
Sven Lidin ◽  
Sten Andersson
Keyword(s):  
High Resolution ◽  
Electron Diffraction ◽  
Structural Model ◽  
Image Intensifier ◽  
Crystalline Materials ◽  
Icosahedral Phases ◽  
Transmission Electron ◽  
Electron Microscopes ◽  
Diffraction Patterns ◽  
Quasi Crystals

High resolution transmission electron microscopy (HRTEM) is playing an important role in identifying the new icosahedral phases. The selected area diffraction patterns of quasi crystals, recorded with an aperture of the radius of many thousands of Ångströms, consist of dense arrays of well defined sharp spots with five fold dilatation symmetry which makes the interpretation of the diffraction process and the resulting images different from those invoked for usual crystals. The atomic structure of the quasi crystals is not established even if several models are proposed. The correct structure model must of course explain the electron diffraction patterns with 5-, 3- and 2-fold symmetry for the phases but it is also important that the HRTEM images of the alloys match the computer simulated images from the model. We have studied quasi crystals of the alloy Al65Cu20Fe15. The electron microscopes used to obtain high resolution electro micrographs and electron diffraction patterns (EDP) were a (S)TEM JEM-2000FX equipped with EDS and PEELS showing a structural resolution of 2.7 Å and a IVEM JEM-4000EX with a UHP40 high resolution pole piece operated at 400 kV and with a structural resolution of 1.6 Å. This microscope is used with a Gatan 622 TV system with an image intensifier, coupled to a YAG screen. It was found that the crystals of the quasi crystalline materials here investigated were more sensitive to beam damage using 400 kV as electron accelerating voltage than when using 200 kV. Low dose techniques were therefore applied to avoid damage of the structure.

Sign in / Sign up

Export Citation Format

Share Document