Regularities of tribooxidation and damageability at the early stage of wear of single-layer (TiAlCrSiY)N and multilayer (TiAlCrSiY)N/(TiAlCr)N coatings in the case of high-speed cutting

2016 ◽  
Vol 52 (3) ◽  
pp. 517-525 ◽  
Author(s):  
A. I. Kovalev ◽  
A. Yu. Rashkovskiy ◽  
G. S. Fox-Rabinovich ◽  
S. Veldhuis ◽  
B. D. Beake
Keyword(s):  
High Speed ◽  
Early Stage ◽  
Single Layer ◽  
High Speed Cutting

RANCANG BANGUN MESIN PEMOTONG RUMPUT TENAGA SURYA UNTUK NAVIGASI

2015 ◽  
Vol 1 (1) ◽  
pp. 5-16
Author(s):  
John Ohoiwutun
Keyword(s):  
High Speed ◽  
Solar Power ◽  
Human Life ◽  
Operating Cost ◽  
Fuel Oil ◽  
Kinematics And Dynamics ◽  
Control Input ◽  
High Speed Cutting ◽  
Lawn Mower ◽  
Coal Fuel

Utilization of conventional energy sources such as coal, fuel oil, natural gas and others on the one hand has a low operating cost, but on the other side of the barriers is the greater source of diminishing returns and, more importantly, the emergence of environmental pollution problems dangerous to human life. This study aims to formulate the kinematics and dynamics to determine the movement of Solar Power Mower. In this study, using solar power as an energy source to charge the battery which then runs the robot. Design and research was conducted in the Department of Mechanical Workshop Faculty of Engineering, University of Hasanuddin of Gowa. Control system used is a manual system using radio wave transmitter and receiver which in turn drive the robot in the direction intended. Experimental results showed that treatment with three variations of the speed of 6.63 m / s, 8.84 m / s and 15.89 m / sec then obtained the best results occur in grass cutting 15.89 sec and high-speed cutting grass 5 cm. Formulation of kinematics and dynamics for lawn mowers, there are 2 control input variables, x and y ̇ ̇ 3 to control the output variables x, y and θ so that there is one variable redudant. Keywords: mobile robots, lawn mower, solar power

APPLICATION OF THE EARLY DAMAGE DIAGNOSTICS TECHNIQUE TO EXAMINATION OF THE AVIATION PANEL

2019 ◽  
Vol 85 (6) ◽  
pp. 53-63 ◽  
Author(s):  
I. E. Vasil’ev ◽  
Yu. G. Matvienko ◽  
A. V. Pankov ◽  
A. G. Kalinin
Keyword(s):  
Acoustic Emission ◽  
Damage Detection ◽  
High Speed ◽  
Early Stage ◽  
Video Data ◽  
High Speed Video ◽  
Damage Diagnostics ◽  
Subsurface Defect ◽  
Sensitive Coating ◽  
Early Damage

The results of using early damage diagnostics technique (developed in the Mechanical Engineering Research Institute of the Russian Academy of Sciences (IMASH RAN) for detecting the latent damage of an aviation panel made of composite material upon bench tensile tests are presented. We have assessed the capabilities of the developed technique and software regarding damage detection at the early stage of panel loading in conditions of elastic strain of the material using brittle strain-sensitive coating and simultaneous crack detection in the coating with a high-speed video camera “Video-print” and acoustic emission system “A-Line 32D.” When revealing a subsurface defect (a notch of the middle stringer) of the aviation panel, the general concept of damage detection at the early stage of loading in conditions of elastic behavior of the material was also tested in the course of the experiment, as well as the software specially developed for cluster analysis and classification of detected location pulses along with the equipment and software for simultaneous recording of video data flows and arrays of acoustic emission (AE) data. Synchronous recording of video images and AE pulses ensured precise control of the cracking process in the brittle strain-sensitive coating (tensocoating)at all stages of the experiment, whereas the use of structural-phenomenological approach kept track of the main trends in damage accumulation at different structural levels and identify the sources of their origin when classifying recorded AE data arrays. The combined use of oxide tensocoatings and high-speed video recording synchronized with the AE control system, provide the possibility of definite determination of the subsurface defect, reveal the maximum principal strains in the area of crack formation, quantify them and identify the main sources of AE signals upon monitoring the state of the aviation panel under loading P = 90 kN, which is about 12% of the critical load.

Recent Patents on the Angular Contact Ball Bearing of High-Speed Motorized Spindle

2020 ◽  
Vol 13 ◽  
Author(s):  
Yudong Bao ◽  
Linkai Wu ◽  
Yanling Zhao ◽  
Chengyi Pan
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Rapid Development ◽  
Ceramic Materials ◽  
Development Trend ◽  
Numerical Control ◽  
Angular Contact Ball Bearing ◽  
Practical Applications ◽  
High Speed Cutting ◽  
Advantages And Disadvantages

Background:: Angular contact ball bearings are the most popular bearing type used in the high speed spindle for machining centers, The performance of the bearing directly affects the machining efficiency of the machine tool, Obtaining a higher value is the direction of its research and development. Objective:: By analyzing the research achievements and patents of electric spindle angular contact bearings, summarizing the development trend provides a reference for the development of electric spindle bearings. Methods:: Through the analysis of the relevant technology of the electric spindle angular contact ball bearing, the advantages and disadvantages of the angular contact ball bearing are introduced, and the research results are combined with the patent analysis. Results:: With the rapid development of high-speed cutting and numerical control technology and the needs of practical applications, the spindle requires higher and higher speeds for bearings. In order to meet the requirements of use, it is necessary to improve the bearing performance by optimizing the structure size and improving the lubrication conditions. Meanwhile, reasonable processing and assembly methods will also have a beneficial effect on bearing performance. Conclusion:: With the continuous deepening of bearing technology research and the use of new structures and ceramic materials has made the bearing's limit speed repeatedly reach new highs. The future development trend of high-speed bearings for electric spindles is environmental protection, intelligence, high speed, high precision and long life.

scholarly journals Detonation effects of shallow buried explosive in sandy soil on target plate acceleration in a small-scale blast test

2018 ◽  
Vol 192 ◽  
pp. 02028
Author(s):  
Hassan Zulkifli Abu ◽  
Ibrahim Aniza ◽  
Mohamad Nor Norazman
Keyword(s):  
Sandy Soil ◽  
High Speed ◽  
Early Stage ◽  
Time History ◽  
Video Camera ◽  
Small Scale ◽  
Target Plate ◽  
Air Blast ◽  
High Speed Video Camera ◽  
The Impact

Small-scale blast tests were carried out to observe and measure the influence of sandy soil towards explosive blast intensity. The tests were to simulate blast impact imparted by anti-vehicular landmine to a lightweight armoured vehicle (LAV). Time of occurrence of the three phases of detonation phase in soil with respect to upward translation time of the test apparatus were recorded using high-speed video camera. At the same time the target plate acceleration was measured using shock accelerometer. It was observed that target plate deformation took place at early stage of the detonation phase before the apparatus moved vertically upwards. Previous data of acceleration-time history and velocity-time history from air blast detonation were compared. It was observed that effects of soil funnelling on blast wave together with the impact from soil ejecta may have contributed to higher blast intensity that characterized detonation in soil, where detonation in soil demonstrated higher plate velocity compared to what occurred in air blast detonation.

The Application of FEA in High-Speed Cutting

2011 ◽  
Vol 287-290 ◽  
pp. 104-107
Author(s):  
Lian Qing Ji ◽  
Kun Liu
Keyword(s):  
High Speed ◽  
Feeding Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Material Model ◽  
Friction Model ◽  
Cutting Depth ◽  
High Speed Cutting ◽  
Key Technologies

The history and application of the FEA are briefly presented in this paper. Several key technologies such as the building of material model, the establishment of the chip - tool friction model as well as meshing are described. Taking the high-speed cutting of titanium alloy (Ti - 10V - 2Fe - 3Al) as an example , reasonable cutting tools and cutting parameters are determinted by simulating the influences of cutting speed, cutting depth and feeding rate on the cutting parameters using FEA.

scholarly journals Surface quality of high-speed cutting plates in flat grinding by new abrasive wheels of “Saint-Gobain Abrasive” company

2020 ◽  
Vol 971 ◽  
pp. 022077
Author(s):  
Nguyen Duy Canh ◽  
Nguyen Van Canh ◽  
Pham Xuan Hong ◽  
Nguyen Ngoc Hue ◽  
Tran Dinh Duy
Keyword(s):  
Surface Quality ◽  
High Speed ◽  
High Speed Cutting

Reliability Models of GSM-R Redundant Network on High-Speed Railway

2012 ◽  
Vol 198-199 ◽  
pp. 1783-1788
Author(s):  
Jun Ting Lin ◽  
Jian Wu Dang
Keyword(s):  
Network Architecture ◽  
High Speed ◽  
Failure Time ◽  
Network Reliability ◽  
Single Layer ◽  
Double Layers ◽  
High Speed Railway ◽  
Reliability Models ◽  
Single Layer Network ◽  
Wireless Architectures

As a dedicated digital mobile communication system designed for railway application, GSM-R must provide reliable bidirectional channel for transmitting security data between trackside equipments and on-train computer on high-speed railways. To ensure the safety of running trains, redundant network architecture is commonly used to guarantee the reliability of GSM-R. Because of the rigid demands of railway security, it is important to build reliability mathematical models, predict the network reliability and select a suitable one. Two common GSM-R wireless architectures, co-sited double layers network and intercross single layer network, are modeled and contrasted in this paper. By calculating the reliabilities of each reliable model, it is clear that more redundant the architecture is, more reliable the system will be, the whole system will bear a less failure time per year as the benefit. Meanwhile, as the redundancy of GSM-R system raises, its equipment and maintenance will cost much, but the reliability raise gently. From the standpoint of transmission system interruption and network equipment failure, the reliability of co-sited double layer network architecture is higher than the intercross single layer one, while the viability and cost of the intercross redundant network is better than co-sited one in natural disasters such as flood and lightning. Taking fully into account reliability, viability and cost, we suggest that intercross redundant network should be chosen on high-speed railway.

Sign in / Sign up

Export Citation Format

Share Document