scholarly journals THE INFLUENCE OF PARTICLE SIZE AND FRICTIONAL/COHESIONAL SHEAR STRENGTH COMPONENTS ON UK SALT MARSH SUBSTRATE STABILITY

2019 ◽  
Author(s):  
HELEN BROOKS ◽  
IRIS MÖLLER ◽  
TOM SPENCER ◽  
KATHERINE ROYSE ◽  
MATTHEW KIRKHAM ◽  
...  
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Salt Marsh ◽  
Substrate Stability

scholarly journals Influence of Structural Plane Microscopic Parameters on Direct Shear Strength

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yanhui Cheng ◽  
Weijun Yang ◽  
Dongliang He
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Stiffness Ratio ◽  
Structural Plane

Structural plane is a key factor in controlling the stability of rock mass engineering. To study the influence of structural plane microscopic parameters on direct shear strength, this paper established the direct shear mechanical model of the structural plane by using the discrete element code PFC2D. From the mesoscopic perspective, the research on the direct shear test for structural plane has been conducted. The bonding strength and friction coefficient of the structural plane are investigated, and the effect of mesoscopic parameters on the shear mechanical behavior of the structural plane has been analyzed. The results show that the internal friction angle φ of the structural plane decreases with the increase of particle contact stiffness ratio. However, the change range of cohesion is small. The internal friction angle decreases first and then increases with the increase of parallel bond stiffness ratio. The influence of particle contact modulus EC on cohesion c is relatively small. The internal friction angle obtained by the direct shear test is larger than that obtained by the triaxial compression test. Parallel bond elastic modulus has a stronger impact on friction angle φ than that on cohesion c. Under the same normal stress conditions, the shear strength of the specimens increases with particle size. The shear strength of the specimen gradually decreases with the increase of the particle size ratio.

Experimental Study on the Effects of Internal Erosion on the Physical and Mechanical Properties of Tailings Under Unsteady Seepage

2021 ◽  
Author(s):  
Rong Gui ◽  
Guicheng He
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Shear Strength ◽  
Average Particle Size ◽  
Physical And Mechanical Properties ◽  
Internal Erosion ◽  
Average Particle ◽  
Sand Column ◽  
Sedimentary Characteristics ◽  
Seepage Erosion

Abstract In this paper, the hydraulic sedimentary model was established to investigate the effects of dry beach slope on the sedimentary characteristics of tailings, and the sand column model was built to investigate the effects of seepage erosion on the physical and mechanical properties of sedimentary tailings under unsteady seepage.The results show that the slope of dry beach have a great effect on the sedimentary characteristics of tailings, the average particle size of tailings decreases along the slope of dry beach, and the larger the slope, the more obvious the stratification of the tailings. The migration of fine-grained tailings caused by seepage erosion increases the permeability of the tailings and reduces the shear strength of the tailings. After seepage erosion,the average particle size of 1#tailings sample, 2#tailings sample and 3#tailings sample increased by 6.4%, 12.0% and 2.4% respectively, the hydraulic conductivity of 1# tailings sample, 2# tailings sample and 3# tailings increased by 27.2%,17.9%, and 15.3% respectively after internal erosion, and the shear strength of 1#tailings sample, 2#tailings sample and 3#tailings sample tailings sample decreased by 20.9 %, 15.1% and 12.4% respectively.

scholarly journals Effects of inclusion of granulated rubber tires on the mechanical behaviour of a compressive sand

2020 ◽  
Vol 57 (5) ◽  
pp. 763-769 ◽  
Author(s):  
W. Li ◽  
C.Y. Kwok ◽  
K. Senetakis
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Mechanical Behaviour ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Rubber Content ◽  
Filling Materials ◽  
Rubber Particles ◽  
Decomposed Granite ◽  
Completely Decomposed Granite

Drained triaxial shearing tests were performed on a well-graded compressive sand (completely decomposed granite, CDG) and its mixtures with granulated rubber tires to investigate the effects of rubber size and content on their mechanical behaviour. Three sizes of rubber particles, GR1, GR2, and GR3, were used with size ratios to CDG (D50,rubber : D50,CDG) of 0.9, 3.5, and 7.2, respectively, and the rubber content ranged from 0% to 30%. The results show that for CDG–GR1 mixtures, the strength decreases with increasing rubber content, while for CDG–GR2 and CDG–GR3 mixtures, the strength decreases only at 10% rubber content and then increases markedly with increasing rubber content. The increase of strength is mainly because the inclusion of large rubber particles widens the particle size distributions of the mixtures, resulting in denser packings. The denser packings also lead to a decrease in compressibility. At larger size ratio and higher rubber content, the CDG–rubber mixtures show higher shear strength and lower compressibility than pure CDG, which indicates the CDG–rubber mixtures are very suitable to be used as filling materials.

Study on the Granular Shear Strength Parameters of Dumping Site

2012 ◽  
Vol 256-259 ◽  
pp. 358-361
Author(s):  
Xiang Yun Kong ◽  
Guang Jin Wang ◽  
Xiao Chao Zhou
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Shear Strength Parameters ◽  
Strength Parameters ◽  
Dumping Site ◽  
Size Grading

Apparent particle size grading is the important characteristic of super-high bench dumping site, and the critical factors with the impact of its stability and disaster prevention are the fragmentation distribution and shear strength parameters of granular. With the copper mine dumping site which had the feature of apparent particle size grading, the thesis carried out the study of on-site particle size investigation and indoor laboratory. The particle-size distribution law with the changing of dumping-site height was analyzed and quantitative relationship between the fragmentation distribution and shear strength parameters of granular was discussed. The research results indicated that coarse-grain contents and maximum grain size were increased significantly according to the decreasing of dumping-site height, which showed that the dumping-site had the feature of apparent particle size grading. The coarse particle content in the grain size composition and internal friction angle φ of shear strength parameters increased with the obvious increment of the distribution value B. The relationship between distribution value B and the internal friction angle φ could be expressed by exponential function curve.

scholarly journals Anisotropic Shear Strength Behavior of Soil–Geogrid Interfaces

2021 ◽  
Vol 11 (23) ◽  
pp. 11387
Author(s):  
Jun Zhang ◽  
Mingchang Ji ◽  
Yafei Jia ◽  
Chenxi Miao ◽  
Cheng Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Great Influence ◽  
Fine Sand ◽  
Coarse Sand ◽  
Shear Direction ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Strength Behavior ◽  
Sand And Gravel

This paper presents an experimental study on the anisotropic shear strength behavior of soil–geogrid interfaces. A new type of interface shear test device was developed, and a series of soil–geogrid interface shear tests were conducted for three different biaxial geogrids and three different triaxial geogrids under the shear directions of 0°, 45° and 90°. Clean fine sand, coarse sand, and gravel were selected as the testing materials to investigate the influence of particle size. The experimental results for the interface shear strength behavior, and the influences of shear direction and particle size are presented and discussed. The results indicate that the interface shear strength under the same normal stress varies with shear direction for all the biaxial and triaxial geogrids investigated, which shows anisotropic shear strength behavior of soil–geogrid interfaces. The soil–biaxial geogrid interfaces show stronger anisotropy than that of the soil–triaxial geogrid interfaces under different shear directions. Particle size has a great influence on the anisotropy shear strength behavior of soil–geogrid interfaces.

scholarly journals Experimental Studies of Scale Effect on the Shear Strength of Coarse-Grained Soil

2022 ◽  
Vol 12 (1) ◽  
pp. 447
Author(s):  
Shuya Li ◽  
Tiancheng Wang ◽  
Hao Wang ◽  
Mingjie Jiang ◽  
Jungao Zhu
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Scale Effect ◽  
Friction Angle ◽  
Coarse Grained ◽  
Test Results ◽  
Maximum Particle Size ◽  
Maximum Particle ◽  
Coarse Grained Soil

Shear strength is an essential index for the evaluation of soil stability. Test results of the shear strength of scaled coarse-grained soil (CGS for short) are usually not able to accurately reflect the actual properties and behaviors of in situ CGS due to the scale effect. Therefore, this study focuses on the influence of the scale effect on the shear strength of scaled CGS, which has an important theoretical significance and application for the strength estimation of CGS in high earth-rock dam engineering. According to previous studies, the main cause of the scale effect for scaled CGS is the variation of the gradation structure as well as the maximum particle size (dmax), in which the gradation structure as a characteristic parameter can be expressed by the gradation area (S). A total of 24 groups of test soil samples with different gradations were designed by changing the maximum particle size dmax and gradation area S. Direct shear tests were conducted in this study to quantitatively explore the effect of the gradation structure and the maximum particle size on the shear strength of CGS. Test results suggest that the shear strength indexes (i.e., the cohesion and internal friction angle) of CGS present an increasing trend with the improvement of the maximum particle size dmax, and thus a logarithmic function relationship among c, φ, and dmax is presented. Both cohesion (c) and internal friction angle (φ) are negatively related to the gradation area (S) in most cases. As a result, an empirical relationship between c, φ, and S is established based on the test results. Furthermore, a new prediction model of shear strength of CGS considering the scale effect is proposed, and the accuracy of this model is verified through the test results provided by relevant literature. Finally, the applicability of this model to different types of CGS is discussed.

scholarly journals Characteristics of Direct Shear and Particle Breakage of Pebble Gravel Materials

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Chenjie Hong ◽  
Man Huang ◽  
Danyu Zhang ◽  
Pingshan Shou ◽  
Zhiyong Zhu
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Large Scale ◽  
Size Range ◽  
Normal Load ◽  
Particle Breakage ◽  
Direct Shear ◽  
Particle Size Range ◽  
Relationship Model ◽  
Characteristic Particle

Particle size is an important factor affecting the Thermal-Hydraulic-Mechanical (THM) coupling behavior of graveled rock mass, especially for the shear mechanical properties. In this study, three groups of the particle size range and nine particle grading samples are designed for a large-scale direct shear test. The relationships between shear stress and shear displacement, shear strength, stress ratio, shear strength parameters, and particle breakage of pebble gravel are analyzed. The influence of particle size range and grade on the strength and particle breakage of gravel material is discussed. Results show evident particle breakage in the process of direct shear, and the degree of fragmentation is controlled by the normal load and the particle size distribution of the sample. The shear strength of the sample is no longer applicable to Mohr-Coulomb strength theory because of particle breakage that is more in line with the power function relationship. Shear strength of pebble gravel material has scale effect, and a corresponding relationship model between friction coefficient f of material and characteristic particle size of the sample is proposed.

scholarly journals Influence of particle size and gradation on shear strength–dilation relation of granular materials

2019 ◽  
Vol 56 (2) ◽  
pp. 208-227 ◽  
Author(s):  
Samaneh Amirpour Harehdasht ◽  
Mahmoud N. Hussien ◽  
Mourad Karray ◽  
Varvara Roubtsova ◽  
Mohamed Chekired
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Shear Strength ◽  
Granular Materials ◽  
Plane Strain ◽  
Computer Code ◽  
Direct Shear ◽  
Shear Tests ◽  
Empirical Formulas ◽  
Direct Shear Tests

Upon close scrutiny of data reported in the literature, taking into account particle-scale characteristics to optimize the precision of the well-known empirical Bolton’s equations and imposing particle-size limits on them is recommended. The present paper examines the potential influence of particle size and grading on the shear strength–dilation relation of granular materials from the results of 276 symmetrical direct shear tests. The applicability of physical symmetrical direct shear tests to interpret the plane strain frictional shearing resistance of granular materials has been widely discussed using the discrete element method (DEM) computer code SiGran. Sixteen different grain-size distribution curves of three different materials were tested at different normal pressures and initial relative densities. It is demonstrated that while the contribution of dilatancy to shear strength is not influenced by the variation in the coefficient of uniformity, Cu, in the investigated range, it significantly decreases with increasing mean particle size, D50. The coefficients of Bolton’s equations have been, therefore, adjusted to account for D50. A comparison of the predictions by the proposed empirical formulas with plane strain friction angle, [Formula: see text], and dilation angle, ψ, data from the literature shows that accounting for the grain size yields more accurate results.

Sign in / Sign up

Export Citation Format

Share Document