Performances of Various Base Isolation Systems in Mitigation of Structural Vibration Due to Underground Blast Induced Ground Motion

2017 ◽  
Vol 17 (04) ◽  
pp. 1750043 ◽  
Author(s):  
Papiya D. Mondal ◽  
Aparna D. Ghosh ◽  
Subrata Chakraborty
Keyword(s):  
Ground Motion ◽  
Base Isolation ◽  
Permanent Deformation ◽  
Structural Vibration ◽  
Design Parameters ◽  
Residual Displacements ◽  
Underground Blast ◽  
Base Isolator ◽  
Isolation Systems ◽  
Friction Pendulum

A comparative study is carried out on the performance of various elastomeric and frictional base isolation (BI) systems in the vibration mitigation of structures subjected to underground blast induced ground motion (BIGM). The parametric sensitivities of the base isolated structures to variations in the design parameters of the isolators are examined for different intensities of blast input. Results indicate that substantial reductions in both the acceleration and displacement responses of the structure can be achieved by the different base isolators. Generally, the Electricite de France (EDF) base isolator produces higher peak response reductions. However, peak bearing displacements are also largest here. The pure friction (P-F), resilient-friction base isolator (R-FBI) and friction pendulum (FP) systems produce lower values of response reductions but peak bearing displacements as well as residual displacements of isolators are also low. The New Zealand (N-Z) system provides good response reductions with a low to moderate value of peak bearing displacement. The present study indicates how a proper selection of the type of BI system with suitable design parameters can mitigate structural vibration due to different intensities of BIGM and restrict the unwanted characteristics of large isolator displacement and its permanent deformation.

A genetic algorithm–based design approach for smart base isolation systems

2017 ◽  
Vol 29 (7) ◽  
pp. 1315-1332 ◽  
Author(s):  
Mohtasham Mohebbi ◽  
Hamed Dadkhah ◽  
Hamed Rasouli Dabbagh
Keyword(s):  
Genetic Algorithm ◽  
Optimization Problem ◽  
Base Isolation ◽  
Design Procedure ◽  
Design Parameters ◽  
Linear Quadratic ◽  
Isolation System ◽  
Isolation Systems ◽  
Magneto Rheological ◽  
Smart Base Isolation

This article presents a new approach for designing effective smart base isolation systems composed of a low-damping linear base isolation and a semi-active magneto-rheological damper. The method is based on transforming the design procedure of the hybrid base isolation system into a constrained optimization problem. The magneto-rheological damper command voltages have been determined using H2/linear quadratic Gaussian and clipped-optimal control algorithms. Through a sensitivity analysis to identify the effective design parameters, base isolation and control algorithm parameters have been taken as design variables and optimally determined using genetic algorithm. To restrict increases in floor accelerations, the objective function of the optimization problem has been defined as minimizing the maximum base drift while putting specific constraint on the acceleration response. For illustration, the proposed method has been applied to design a semi-active hybrid isolation system for a four-story shear building under earthquake excitation. The results of numerical simulations show the effectiveness, simplicity, and capability of the proposed method. Furthermore, it has been shown that using the proposed method, the acceleration of the isolated structure can also be incorporated into design process and practically controlled with a slight sacrifice of control effectiveness in reducing the base drift.

Effects of Damper Force Ranges and Ground Motion Pulse Periods on the Performance of Semi-Active Isolation Systems

2003 ◽  
Author(s):  
Henri Gavin ◽  
Julie Thurston ◽  
Chicahiro Minowa ◽  
Hideo Fujitani
Keyword(s):  
Ground Motion ◽  
Large Scale ◽  
Base Isolation ◽  
Near Field ◽  
Shaking Table ◽  
Isolation System ◽  
Active Isolation ◽  
Isolation Systems ◽  
Fail Safe ◽  
Strong Ground

A large-scale base-isolated steel structural frame was tested at the shaking table laboratory of the National Research Institute for Earth Sciences and Disaster Prevention. These collaborative experiments featured auto-adaptive media and devices to enhance the performance of passive base isolation systems. The planning of these experiments involved determining appropriate device control methods, the development of a controllable damping device with fail-safe characteristics, and the evaluation of the performance of the controlled isolation system subjected to strong ground motion with pronounced near-field effects. The results of the planning study and their large-scale experimental confirmation provide guidelines for the development and implementation of auto-adaptive damping devices for full scale structures.

The effects of input earthquake characteristics on the nonlinear dynamic behavior of FPS isolated liquid storage tanks

2016 ◽  
Vol 24 (7) ◽  
pp. 1264-1282 ◽  
Author(s):  
Saman Bagheri ◽  
Mostafa Farajian
Keyword(s):  
Passive Control ◽  
Base Isolation ◽  
Ground Motions ◽  
Storage Tanks ◽  
Ground Acceleration ◽  
Pendulum System ◽  
Aspect Ratios ◽  
Liquid Storage ◽  
Isolation Systems ◽  
Friction Pendulum

There are several methods to reduce the seismic damages in liquid storage tanks. One of these methods is to use passive control devices, in particular seismic base isolators. Among the different base isolation systems, the Friction Pendulum System (FPS) whose period does not depend on the weight of the system is more appropriate for isolation of liquid storage tanks. The aim of this paper is to investigate the effects of peak ground acceleration (PGA) and pulselike characteristics of earthquakes on the seismic behavior of steel liquid storage tanks base isolated by FPS bearings. In addition, impact effects of the slider with the side retainer are investigated, as well as effects of tank aspect ratio, isolation period and friction coefficient. The obtained results of tanks with different aspect ratios indicate that the responses get more reduced due to isolation under far-field ground motions compared to near-fault ground motions. It is also seen that the response of a base isolated tank is affected when contact takes place with the side retainer of the FPS.

scholarly journals Effects of Shape Memory Alloys on Response of Steel Structural Buildings within Near Field Earthquakes Zone

2020 ◽  
Vol 6 (7) ◽  
pp. 1314-1327
Author(s):  
Mahmoud Ahmadinejad ◽  
Alireza Jafarisirizi ◽  
Reza Rahgozar
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Base Isolation ◽  
Near Field ◽  
Seismic Zone ◽  
Isolation System ◽  
Residual Displacements ◽  
Rubber Bearing ◽  
Laminated Rubber Bearing ◽  
Isolation Systems

Base isolation is one of the effective ways for controlling civil engineering structures in seismic zone which can reduce seismic demand. Also is an efficient passive control mechanism that protects its superstructure during an earthquake. However, residual displacement of base-isolation systems, resulting from strong ground motions, remain as the main obstacle in such system’s serviceability after the earthquake. Shape Memory Alloys (SMA) is amongst the newly introduced smart materials that can undergo large nonlinear deformations with considerable dissipation of energy without having any permanent displacement afterward. This property of SMA may be utilized for designing of base isolation system to increase the structure’s serviceability. Here, a proposed semi-active isolation system combines laminated rubber bearing system with shape memory alloy, to take advantage of SMAs high elastic strain range, in order to reduce residual displacements of the laminated rubber bearing. Merits of the system are demonstrated by comparing it to common laminated rubber bearing isolation systems. It is found that the optimal application of SMAs in base-isolation systems can significantly reduce bearings’ residual displacements. In this study, OpenSees program for a three dimensional six-storey steel frame building has been used by locating the isolators under the columns for investigating the feasibility of smart base isolation systems, i.e., the combination of traditional Laminated Rubber Bearing (LRB) with the SMA, in reducing the structure’s isolated-base response to near field earthquake records are examined. Also, a new configuration of SMAs in conjunction with LRB is considered which make the system easier to operate and maintain.

scholarly journals Performance Analysis and Comparison of Two Base Isolation Systems with Super-Large Displacement Friction Pendulum Bearings

2020 ◽  
Vol 10 (22) ◽  
pp. 8235
Author(s):  
Peisong Wu ◽  
Jinping Ou
Keyword(s):  
Seismic Performance ◽  
Base Isolation ◽  
Design Method ◽  
Horizontal Displacement ◽  
Large Displacement ◽  
Large Radius ◽  
Isolation Layer ◽  
Deformation Ability ◽  
Isolation Systems ◽  
Friction Pendulum

Isolation technology has been successfully applied in seismic migration. With increasing of seismic demand, seismic performance of isolation structures subjected to very-rare earthquakes need further improvement. However, the isolation layer generally lacks sufficient deformation ability under very-rare earthquakes due to the deformation limit of classical isolation bearing. In order to circumvent the difficulty, this paper develops two new isolation bearings, namely super-large displacement rotation friction pendulum bearing (SLDRFPB) and super-large displacement translation friction pendulum bearing (SLDTFPB). By setting spherical shells with large span and large radius, large horizontal displacement and small horizontal stiffness can be achieved. Safety of the isolation layer and the isolation effect of the superstructure can be greatly improved. SLDTFPB differs from SLDRFPB in the motion state of the superstructure and space utilization of the isolation layer, thus SLDRFPB and SLDTFPB are suitable for structures with different requirements. Due to rotation of the superstructure with SLDRFPB or sliding frames in SLDTFPB, the traditional design method of friction pendulum bearing is no longer suitable. We present a new procedure to accurately and conveniently evaluate seismic performance of two developed bearings. Numerical simulation shows that the seismic response of both the superstructure and isolation layer is small. Developed SLDRFPB and SLDTFPB have sufficient emergency capacity and isolation resilience when subjected to very-rare earthquakes.

Comparative Studies of Base Isolation Systems Featured with Lead Rubber Bearings and Friction Pendulum Bearings

2016 ◽  
Vol 846 ◽  
pp. 114-119
Author(s):  
Arati Pokhrel ◽  
Jian Chun Li ◽  
Yan Cheng Li ◽  
Nicos Maksis ◽  
Yang Yu
Keyword(s):  
Seismic Isolation ◽  
Base Isolation ◽  
Time History ◽  
Elastic Base ◽  
Base Shear ◽  
Isolation Technique ◽  
Rubber Bearing ◽  
Lead Rubber Bearing ◽  
Isolation Systems ◽  
Friction Pendulum

Due to the fact that safety is the major concern for civil structures in a seismic active zone, it has always been a challenge for structural engineers to protect structures from earthquake. During past several decades base isolation technique has become more and more popular in the field of seismic protection which can be adopted for new structures as well as the retrofit of existing structures. The objective of this study is to evaluate the behaviours of the building with different seismic isolation systems in terms of roof acceleration, elastic base shear and inter-storey drift under four benchmark earthquakes, namely, El Centro, Northridge, Hachinohe and Kobe earthquakes. Firstly, the design of base isolation systems, i.e. lead rubber bearing (LRB) and friction pendulum bearing (FPB) for five storey RC building was introduced in detail. The non-linear time history analysis was performed in order to determine the structural responses whereas Bouc-Wen Model of hysteresis was adopted for modelling the bilinear behaviour of the bearings. Both isolation systems increase the fundamental period of structures and reduces the spectral acceleration, and hence reduces the lateral force cause by earthquake in the structures, resulting in significant improvement in building performance; however the Lead Rubber Bearing provided the best reduction in elastic base shear and inter-storey drift (at first floor) for most of the benchmark earthquakes. For the adopted bearing characteristics, FPB provided the low isolator displacement.

Effect of Velocity Dependence on Sliding Characteristic of Sliding Types of Base Isolation Systems Each With Numerous Sliding Interfaces

2011 ◽  
Author(s):  
C. S. Tsai ◽  
H. C. Su ◽  
T. C. Chiang
Keyword(s):  
Base Isolation ◽  
Velocity Dependence ◽  
Analysis Software ◽  
Pendulum System ◽  
Sliding Interfaces ◽  
Velocity Effect ◽  
Isolation Systems ◽  
Friction Pendulum ◽  
The Given ◽  
Base Isolators

Current structural analysis software programs offer few if any applicable device-specific hysteresis rules or nonlinear elements considering the velocity effect on the mechanical behavior of the multiple friction pendulum system (MFPS) with numerous sliding interfaces. Based on the concept of subsystems, here we propose an equivalent series system that adopts existing nonlinear elements with parameters systematically calculated and mathematically proven through rigorous derivations to take into account the velocity dependence effect on the sliding behavior of the sliding interfaces in the sliding type base isolators. Evaluations of the velocity dependence effect on the features of the sliding motions on numerous sliding interfaces have also been carried out. Results from the given examples demonstrate that the sliding motions of sliding interfaces considering velocity dependence behave quite differently from those excluding the effect of velocity dependence.

scholarly journals Performance of elevated water tank staging with base isolation under blast loading

2021 ◽  
Vol 309 ◽  
pp. 01134
Author(s):  
Boda Balaraju ◽  
Atulkumar Manchalwar
Keyword(s):  
Base Isolation ◽  
Linear Time ◽  
Time History ◽  
Water Tank ◽  
Base Shear ◽  
Isolation Technique ◽  
Underground Blast ◽  
Base Isolator ◽  
Fixed Base ◽  
Elevated Water

In this present study aims to evaluate the performance of base isolation device under different intensity blast induced ground excitations for an elevated water tank staging. In this study mainly focused to improve the performance of the base isolator and minimize the damage of the structure. To know the performance of base isolator two models are considered one is fixed base model and another one is supported with base isolator model for both non-linear time history analysis is carried out with the help of SAP 2000 software subjected to four different underground blast intensities. From the analysis, it is observed that by using base isolator supported model structural responsive parameters such as base shear, top storey accelerations are efficiently reduced when compared to the fixed base structure. Hence it is proved that adopting base isolation technique we considerably reduce the damage of the structure subjected to underground blast vibrations.

scholarly journals Shaking table tests of a base isolated structure with Double Concave Friction Pendulum bearings

2015 ◽  
Vol 48 (2) ◽  
pp. 136-144 ◽  
Author(s):  
Felice C. Ponzo ◽  
Antonio D. Cesare ◽  
Gianmarco Leccese ◽  
Domenico Nigro
Keyword(s):  
Base Isolation ◽  
Experimental Testing ◽  
Design Procedure ◽  
Time History ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Isolation System ◽  
Sliding Surfaces ◽  
Residual Displacements ◽  
Friction Pendulum

An extensive experimental testing programme named JETBIS project (Joint Experimental Testing of Base Isolation Systems) was developed within the RELUIS II project (Task 2.3.2) and RELUIS III project (Line 6) involving partners from different Italian universities. This paper describes the seismic tests performed by the research unit of University of Basilicata (UNIBAS) on an isolation system based on Double Concave Friction Pendulum (DCFP) bearings. The DCFP bearing contains two separate concave sliding surfaces and exhibits different hysteretic properties at different stages of displacement response. The main objective of this work is to evaluate the horizontal response of the DCFP isolators by means of controlled-displacement tests and shaking table tests. The experimental model was a 1/3 scaled steel framed structure with one storey and one bay in both directions. Four DCFP bearings with equal properties of the sliding surfaces were considered. In this work, three different sliding surface conditions (with and without lubrication) have been studied. The isolated base model was subjected to 8 natural earthquakes of increasing seismic intensities and considering two mass configurations (with both symmetrical and eccentric masses). The reliability of the design procedure considered for the isolation system was verified also when relevant residual displacements occurred due to previous earthquakes. In this paper, the comparisons between the experimental outcomes and the numerical results of nonlinear time-history analyses using SAP2000 are shown.

Sign in / Sign up

Export Citation Format

Share Document