Synthesis of Cu Loaded TiO2 Nanoparticles for the Improved Photocatalytic Degradation of Rhodamine B

2016 ◽  
Vol 15 (05n06) ◽  
pp. 1660002 ◽  
Author(s):  
V. Kavitha ◽  
P. S. Ramesh ◽  
D. Geetha
Keyword(s):  
Titanium Dioxide ◽  
Rhodamine B ◽  
Sol Gel ◽  
Average Particle Size ◽  
Visible Spectrum ◽  
Xrd Analysis ◽  
Bandgap Energy ◽  
Average Particle ◽  
Titanium Tetraisopropoxide ◽  
Photoexcited Electron

Copper doped Titanium dioxide TiO2 nanoparticles were synthesized by sol–gel method using titanium tetraisopropoxide and copper sulfate as precursors. The synthesized nanoparticles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), UV-Visible spectroscopy (UV-Vis), Photoluminesce spectroscopy (PL) and atomic force microscopy (AFM). XRD analysis confirms the formation of anatase titanium dioxide and average particle size was 35[Formula: see text]nm. Cu– TiO2 exhibits a shift in the absorption edge toward visible spectrum. The rate of recombination and transfer behavior of the photoexcited electron–hole pairs in the semiconductors was recorded by photoluminescence. From SEM spherical shaped nanoparticles was observed. Comparing with pure TiO2 nanoparticles, Cu doped TiO2 photocatalyst exhibited enhanced photocatalytic activity under natural sunlight irradiation in the decomposition of rhodamine B aqueous solution. The maximum 97% of degradation efficiency of Rhodamine B was observed at 0.6% Cu–TiO2 within 180[Formula: see text]min. The photocatalytic efficiency of Rhodamine B of Cu doped TiO2 nanoparticle was higher than the pure TiO2, which could be attributed to the small crystallinity intense light absorption in Sunlight and narrow bandgap energy of Copper.

Porous Ceramic Humidity Sensors Using Sol-Gel Processed ZrTiO4 Nanoparticles

2006 ◽  
Vol 45 ◽  
pp. 1803-1808 ◽  
Author(s):  
I.C. Cosentino ◽  
E.N.S. Muccillo ◽  
F.M. Vichi ◽  
R. Muccillo
Keyword(s):  
Porous Ceramic ◽  
Mercury Porosimetry ◽  
Sol Gel ◽  
Average Particle Size ◽  
Nitrogen Adsorption ◽  
Zirconium Oxychloride ◽  
Average Particle ◽  
Titanium Tetraisopropoxide ◽  
X Ray Diffraction ◽  
Adsorption Analysis

Ceramic ZrTiO4 powders were prepared by a sol-gel method using zirconium oxychloride and titanium tetraisopropoxide. In situ high temperature X-ray diffraction results show that crystallization of the amorphous gel starts at 400°C. Single-phase ZrTiO4 nanoparticles of 46 nm average particle size, determined by nitrogen adsorption analysis, were obtained after heat treatment at 450°C for 1 h. After pressing these sinteractive powders, pellets with controlled pore size distribution were obtained by sintering at temperatures as low as 400°C. The analysis of pores by mercury porosimetry gives an average porosity of 45%. The electrical resistivity, determined by impedance spectroscopy measurements at 24°C under different humidity environments, shows the ability of these pellets to adsorb water vapor in the porous surfaces.

scholarly journals Structural and optical properties of TiO2 nanoparticles and their photocatalytic behavior under visible light

2021 ◽  
Vol 23 (2) ◽  
pp. e21310965
Author(s):  
Edgar Eduardo Mosquera ◽  
Daniela Herrera-Molina ◽  
Jesús Diosa
Keyword(s):  
Optical Properties ◽  
Visible Light ◽  
Tio2 Nanoparticles ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Average Particle Size ◽  
Bandgap Energy ◽  
Average Particle ◽  
Thermal Treatments ◽  
Structural And Optical Properties

TiO2 nanoparticles were successfully synthesized using a facile and scalable sol-gel method and their structural and optical properties studied. XRD ad FTIR was used to identify the phase, crystallite size, and functional groups present in the nanoparticles. The prepared samples crystallize in the anatase structure with highly crystalline order. TEM/EDX shows that the nanoparticles are pure, spherical, and with an average particle size of 15 ± 2 nm. The bandgap energy was 3.59, 3.79, and 3.64 eV, respectively. PL emission is attributed to oxygen vacancies (Vo). The calcination temperature at 450 °C suggests a better photocatalytic performance under visible light compared with other sample's thermal treatments.

Synthesis and Characterization of Nanosized ZrTiO4 Powders Prepared by the Sol-Gel Method

2006 ◽  
Vol 530-531 ◽  
pp. 401-407 ◽  
Author(s):  
I.C. Cosentino ◽  
F.M. Vichi ◽  
E.N.S. Muccillo ◽  
R. Muccillo
Keyword(s):  
Mercury Porosimetry ◽  
Sol Gel ◽  
Average Particle Size ◽  
Nitrogen Adsorption ◽  
Zirconium Oxychloride ◽  
Average Particle ◽  
Titanium Tetraisopropoxide ◽  
Nanosized Powders ◽  
Gel Method ◽  
Sol Gel Method

Ceramic ZrTiO4 powders were prepared by a modified sol-gel method using zirconium oxychloride and titanium tetraisopropoxide. In situ high temperature X-ray diffraction results show that crystallization of the amorphous gel starts at 400 °C. Singlephase ZrTiO4 nanoparticles were obtained after heat treatment at 450 oC for 1 h. An average particle size of 46 nm has been determined by nitrogen adsorption analysis. After pressing these sinteractive powders, pellets with controlled pore size distribution were obtained by sintering at temperatures as low as 400 oC. The analysis of pores by mercury porosimetry shows an average porosity of 45 %. Pressing and sintering the nanosized powders prepared by that modified sol-gel technique produced pellets that are good candidates to be used in humidity sensing devices.

scholarly journals Studying the Crystal Structure, Topography, and Anti-bacterial of a Novel Titania (TiO2 NPs) Prepared by a Sol-gel Manner

2019 ◽  
Vol 16 (4) ◽  
pp. 0910
Author(s):  
Fayyadh Et al.
Keyword(s):  
Particle Size ◽  
Antibacterial Activity ◽  
Titanium Dioxide ◽  
Calcination Temperature ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
Gram Negative ◽  
Tio2 Nps ◽  
Average Grain Size

In this research, titanium dioxide nanoparticles (TiO2 NPs) were prepared through the sol-gel process at an acidic medium (pH3).TiO2 nanoparticles were prepared from titanium trichloride (TiCl3) as a precursor with Ammonium hydroxide (NH4OH) with 1:3 ratio at 50 °C. The resulting gel was dried at 70 °C to obtain the Nanocrystalline powder. The powder from the drying process was treated thermally at temperatures 500 °C and 700 °C. The crystalline structure, surface morphology, and particle size were studied by using X-ray diffraction (XRD), Atomic Force Microscopy (AFM), and Scanning Electron Microscope (SEM). The results showed (anatase) phase of titanium dioxide with the average grain size of 110 nm at 500 °C calcination temperature, and (anatase- rutile) mixed phase of titanium dioxide with the average particle size of 118.1 nm at 700 °C calcination temperature. The anti-bacterial activity of the synthesis specimens was recorded through the Kirby-Bauer disc method (disc devotion method). The results displayed a pretty excellent antibacterial activity of TiO2 NPs to bacteria strains: Gram positive staphylococcus aureus, gram negative pseudomonas aeruginosa, and "gram negative escherichia coli. The sensitivity of the tested bacteria to TiO2 NPs depends on the oxidation state of the TiO2 NPs, particle size, volume, and the density of the unit cell. The small- average particle size of titanium dioxide particles showed high antibacterial activity against bacteria, while the larger- average particle size of titanium dioxide particles showed less antibacterial activity. The novelty of this production is the manufacturing of a novel kind of TiO2 NPs and achievement its best antibacterial activity.

SYNTHESIS AND CHARACTERIZATION OF TITANIUM DIOXIDE DOPED WITH Sc3+ IONS

2006 ◽  
Vol 05 (02n03) ◽  
pp. 351-357 ◽  
Author(s):  
YOUNG SOO KANG ◽  
DONG RI ZHANG
Keyword(s):  
Titanium Dioxide ◽  
Anatase Phase ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Ft Ir ◽  
Xrd Patterns

Nanoparticles of titanium dioxide ( TiO 2) doped with 5 at.% Sc 3+ ions were synthesized using the sol–gel method and calcined at 500°C to obtain better anatase phase. The crystal structures of the doped TiO 2 nanoparticles were characterized by X-ray powder diffraction (XRD), Raman, UV-vis, FT-IR spectroscopy, high resolution transmission electron microscopy (HRTEM) and selected-area electron diffraction (SAED). XRD patterns and Raman spectra of TiO 2 + 5 at.% Sc -500°C show the anatase phase and the average particle size of the sample calculated from XRD patterns was determined as 5.9 nm. Well-resolved rings of SAED of TiO 2 doped with Sc 3+ ions are easily indexed to those from XRD pattern. HRTEM shows the well-defined lattice fringes and the lattice spacing measured from HRTEM is 0.33 nm, which is in well agreement with the distance between the (101) planes in anatase TiO 2. Energy-dispersive X-ray (EDX) spectrum of the doped TiO 2 confirms the presence of Sc element in the TiO 2 matrix.

Nanocrystalline α-Fe2O3: A Superparamagnetic Material for w-LED Application and Waste Water Treatment

2021 ◽  
Author(s):  
Mahesh Gaidhane ◽  
Deepak Taikar ◽  
Pravin Gaidhane ◽  
Kalpana Nagde
Keyword(s):  
Photocatalytic Activity ◽  
Waste Water Treatment ◽  
Sol Gel ◽  
Average Particle Size ◽  
Emission Spectra ◽  
Broad Emission Band ◽  
Average Particle ◽  
X Ray ◽  
Prepared Material ◽  
Cie Chromaticity

Abstract Nanocrystalline α-Fe2O3 is synthesized by sol-gel technique. The prepared nanomaterial was characterized by X-ray diffraction (XRD), SEM, TEM, Fourier Transform Infrared (FTIR) spectroscopy, Vibrating Sample Magnetometry (VSM) and photoluminescence (PL) techniques. X-ray powder diffraction analysis confirmed the formation of α-Fe2O3. Electron microscopy showed spherical morphologies with an average particle size of 30-40 nm. The magnetic property of the prepared material was studied by VSM at room temperature. VSM study shows superparamagnetic nature of the synthesized nanoparticles. Photoluminescence (PL) emission spectra show intense broad emission band centered at 570 nm with 393 nm excitation indicating its usefulness for w-LED application. The CIE-chromaticity color coordinates of prepared material were calculated. The photocatalytic activity of the α-Fe2O3 nanoparticles was analyzed and the nanopowder exhibited good photocatalytic activity for the removal AO7 from its aqueous solution.

Preparation of Magnesium-Based Cobalt-Ferrites (Co1−xMgxFe2O4) Nanoparticles by Sol–Gel Auto Combustion Method

2017 ◽  
Vol 17 (01n02) ◽  
pp. 1760012
Author(s):  
S. Gowreesan ◽  
A. Ruban Kumar
Keyword(s):  
Particle Size ◽  
Structural Parameters ◽  
Sol Gel ◽  
Average Particle Size ◽  
Combustion Method ◽  
Dielectric Behavior ◽  
Powder Xrd ◽  
Average Particle ◽  
Cobalt Ferrites ◽  
Auto Combustion

The scope of the present work is in enhancing the particle size, and dielectric properties of Mg-substituted Cobalt ferrites nanoparticles prepared by sol–gel auto combustion method. The different ratios of Mg-substituted Co Ferrites (Co[Formula: see text]MgxFe2O4([Formula: see text], 0.05, 0.10, 0.15, 0.20 and 0.30)) are calcinated at 850[Formula: see text]C. The synthesized nanoparticles were characterized by powder XRD, FTIR, FE-SEM, EDX techniques and dielectric behavior. The structural parameters were confirmed from powder XRD and the average particle size is obtained from 39 to 67 nm due to the substitution of Mg[Formula: see text] which was calculated by Debye Scherrer’s formula. FE-SEM showed the surface morphology of the different ratio of the sample. The dielectric loss has measured the frequency range of 50[Formula: see text]Hz–5[Formula: see text]MHz. From electrical modulus, conductivity relaxation and thermal activation of charge carriers has been discussed.

Fabrication and Microstructure of ZnO-TiO2 Composite Membranes by a Reverse Micelle and Sol-Gel Processing

2006 ◽  
Vol 510-511 ◽  
pp. 786-789 ◽  
Author(s):  
Dong Sik Bae ◽  
Byung Ik Kim ◽  
Kyong Sop Han
Keyword(s):  
Particle Size ◽  
Reverse Micelle ◽  
Porous Alumina ◽  
Sol Gel ◽  
Average Particle Size ◽  
Composite Membranes ◽  
Dip Coating ◽  
Narrow Particle Size Distribution ◽  
Average Particle ◽  
Alumina Support

ZnO-TiO2 nanoparticles were synthesized by a reverse micelle and sol-gel process. The average particle size of the colloid was below 30 nm and well dispersed in the solution. ZnOTiO2 composite membranes were fabricated by using the dip-coating method on a porous alumina support. ZnO-TiO2 composite membranes showed a crack-free microstructure and narrow particle size distribution even after the heat treatment up to 600°C. The average particle size of the membrane was 30-40nm, and the pore size of ZnO-TiO2 composite membrane was below 10 nm.

scholarly journals A Comparative Study of Nanostructures of CuO/Cu2O Fabricated via Potentiostatic and Galvanostatic Anodization

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
S. Mary Margaret ◽  
Albin John P. Paul Winston ◽  
S. Muthupandi ◽  
P. Shobha ◽  
P. Sagayaraj
Keyword(s):  
Thermal Stability ◽  
Comparative Study ◽  
Aqueous Electrolyte ◽  
Average Particle Size ◽  
Xrd Analysis ◽  
Molecular Vibration ◽  
Synthesis Process ◽  
Average Particle ◽  
Good Crystallinity ◽  
Cu Foil

A detailed comparative study on the synthesis process of coral-like CuO/Cu2O nanorods (NRs) and nanopolycrystals (NPCs) fabricated on Cu foil employing aqueous electrolyte via potentiostatic (POT) and galvanostatic (GAL) modes is discussed. The structural, morphological, thermal, compositional, and molecular vibration of the prepared CuO/Cu2O nanostructures was characterized by XRD, HRSEM, TG/DTA, FTIR, and EDX techniques. XRD analysis confirmed the crystalline phase of the formation of monoclinic CuO and cubic Cu2O nanostructures with well-defined morphology. The average particle size was found to be 21.52 nm and 26.59 nm for NRs (POT) and NPCs (GAL), respectively, and this result is corroborated from the HRSEM analysis. POT synthesized nanoparticle depicted a higher thermal stability up to 600°C implying that the potentiostatically grown coral-like NRs exhibit a good crystallinity and well-ordered morphology.

scholarly journals Sintesis Nanopartikel Perak Menggunakan Ekstrak Daun Kluwak Pangium edule Reinw Sebagai Bioreduktor dan Uji Aktivitasnya Sebagai Antioksidan

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Indrawati Patabang ◽  
Syahruddin Kasim ◽  
Paulina Taba
Keyword(s):  
Antioxidant Activity ◽  
Particle Size ◽  
Silver Nanoparticles ◽  
Leaf Extract ◽  
Average Particle Size ◽  
Xrd Analysis ◽  
Average Particle ◽  
Result Show ◽  
Ic50 Values ◽  
Show Result

Silver nanoparticles have been synthesized using kluwak leaf extract (Pangium edule Reinw) as bioreductor and antioxidant activity assay. The nanoparticles formed were monitored by observing UV-Vis absorption and characterized by using FTIR, PSA, XRD and SEM instruments. The result of functional group characterization with FTIR show that the functional groups OH, C = O, C-O and CH2 act as Ag+ reducing agent. The size of silver nanoparticles was determined by using Particle Size Analyzer (PSA) and the result show average particle size distribution of 93.2 nm. Morphology of AgNp were observed by Scanning Electron Microscope (SEM) and X-Ray Difraction (XRD) analysis show result of 51,78 nm. The antioxidant activity was shown by in kluwak leaf extract and silver nanoparticles with IC50 values respectively 831,33 ppm dan 1493,09 ppm.

Sign in / Sign up

Export Citation Format

Share Document