Photoluminescence properties of Na1.45La8.55(SiO4)6(F0.9O1.1):Eu for applications as a reddish orange phosphor

2014 ◽  
Vol 07 (05) ◽  
pp. 1450060 ◽  
Author(s):  
Qun Shi ◽  
Dhia A. Hassan ◽  
Renjie Zeng
Keyword(s):  
Spectral Analysis ◽  
Solid State Reaction Method ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Analysis System ◽  
Reddish Orange ◽  
The Eu

Europium-doped Na 1.45 La 8.55-8.55x( SiO 4)6( F 0.9 O 1.1)(0.000 ≤ x ≤ 0.045) phosphors were prepared by a conventional solid-state reaction method at 1200°C and their properties were studied by X-ray diffraction (XRD), and a spectral analysis system. No impurities were observed. The phosphor could be excited at 254 nm, 395 nm and 465 nm to yield a reddish orange emission which was attributed to the 5 D 0 → 7 F j (j = 0–2) transitions of the Eu ion.

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

Photoluminescence properties of Li2+xNb3xTi1−4xO3:Eu3+

2019 ◽  
Vol 12 (04) ◽  
pp. 1950057 ◽  
Author(s):  
Chao-Chao Guo ◽  
Qun Zeng ◽  
Chun-Feng Yao ◽  
Yan-Zhao Feng ◽  
Xi Chen ◽  
...  
Keyword(s):  
Solid State ◽  
Emission Spectra ◽  
Solid State Reaction Method ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
Red Emission ◽  
Reaction Method ◽  
X Ray ◽  
Red Phosphors ◽  
Chromaticity Coordinate

Red phosphors with compositions of Li[Formula: see text]Nb[Formula: see text]Ti[Formula: see text]O3:3[Formula: see text]wt.% Eu[Formula: see text] [Formula: see text] were synthesized by solid-state reaction method. The samples were investigated by using X-ray diffraction (XRD) and photoluminescence spectroscopy, respectively. XRD results showed that all samples were main phase of Li2TiO3. Emission spectra of Li[Formula: see text]Nb[Formula: see text]Ti[Formula: see text]O3:3[Formula: see text]wt.% Eu[Formula: see text] powders showed strong red emission at 612[Formula: see text]nm (5D0–7F[Formula: see text] with 396[Formula: see text]nm excitation. In addition, the excitation and emission intensity increased up to [Formula: see text], and then decreased with further increasing of the x values. And the chromaticity coordinate (CIE) of the component with [Formula: see text] was superior to other components.

Structural and Dielectric Properties of Na0.5Bi0.5TiO3 Ferroelectric Ceramics

2012 ◽  
Vol 585 ◽  
pp. 219-223
Author(s):  
Rekha Kumari ◽  
N. Ahlawat ◽  
Ashish Agarwal ◽  
M. Sindhu ◽  
N.N. Ahlawat
Keyword(s):  
Dielectric Properties ◽  
Solid State Reaction Method ◽  
Wide Frequency Range ◽  
Ferroelectric Ceramics ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Different Temperatures

Na0.5Bi0.5TiO3 (NBT) ceramics were synthesized by conventional solid state reaction method. Structural and dielectric properties of these ceramics were investigated. Crystalline phase of sintered ceramics was investigated by X-ray diffraction (XRD). The Rietveld refinement of powder X-ray diffraction revealed that the prepared ceramics exhibit the rhombohedral space group R3c. Dielectric properties of Na0.5Bi0. analyzer.5TiO3 (NBT) ceramics were studied at different temperatures in a wide frequency range using impedance

Magnetic and Transport Properties Ru1 - xSbxSr2(Sm0.7Ce0.3)2Cu2O10 - δ Compounds

2003 ◽  
Vol 17 (13) ◽  
pp. 2539-2544 ◽  
Author(s):  
T. R. Yang ◽  
V. Toma ◽  
O. Furdui ◽  
G. Ilonca
Keyword(s):  
Magnetic Order ◽  
Solid State Reaction Method ◽  
Partial Substitution ◽  
Superconducting Transition ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Sb Doping ◽  
Hole Localization

We have investigated the effect of the partial substitution of Sb for Ru in Ru 1 - x Sb x Sr 2( Sm 0.7 Ce 0.3)2 Cu 2 O 10 - δ, (Ru:1222) prepared by conventional solid state reaction method, using X-ray diffraction analysis, electrical resistivity and DC-magnetic susceptibility measurements. Sb doping reduces the conductivity of the system and the onset superconducting transition temperature decreases from 42 K for x = 0 to 21 K for x = 0.06. This maybe due to a distortion of RuO6 octahedral, which is responsible of the increase in hole localization. The corresponding magnetic moment in the investigated samples is about 0.1 μB for Ru. Furthermore we discuss the influence of phase composition on superconducting and magnetic order.

scholarly journals Study of the Structural, Magnetic and Transport properties of La3+ Doped Cu-Zn Ferrite

2020 ◽  
Vol 12 (3) ◽  
pp. 259-267
Author(s):  
K. Nahar ◽  
M. A. Hossain ◽  
P. Roy ◽  
M. N. I. Khan ◽  
S. S. Sikder
Keyword(s):  
Solid State ◽  
Diffraction Pattern ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Zn Ferrite ◽  
La Doped

Crystalline La doped Cu-Zn ferrite with compositions Cu0.15Zn0.85LaxFe2-xO4 [ x = 0.00, 0.02, 0.04, 0.06 and 0.08] were synthesized by using conventional solid state reaction method technique. X-ray diffraction pattern (XRD), Crystalline La doped Cu-Zn ferrite with compositions Cu0.15Zn0.85LaxFe2-xO4 [x = 0.00, 0.02, 0.04, 0.06 and 0.08] were synthesized by using conventional solid state reaction method technique. X-ray diffraction pattern (XRD), scanning electron micrographs (SEM), hysteresis loop (M-H) curves and frequency dependent resistivity were employed to inspect the effect of La3+ doping on the structure, microstructure, magnetic and transport properties of the specimens. All the specimens exhibited fcc type cubic spinel structure where the particle size were within 500-1600 nm range. Magnetically ferromagnetic phenomenon was found for all the samples where the effect of La3+ doping consequence on the variation of various parameters like saturation magnetization (Ms), coercivity (Hc) and remanent magnetization (Mr). The resistivity tuned by frequency for all the samples presented the decreasing phenomenon with the increase of applied frequency.

Photoluminescence Properties of Eu3+-activated Silicate Phosphors

2017 ◽  
Vol 36 (6) ◽  
pp. 635-640
Author(s):  
Esra Öztürk
Keyword(s):  
High Temperature ◽  
Solid State ◽  
Solid State Reaction Method ◽  
Sintering Process ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Host Lattices ◽  
Silicate Phosphors

AbstractThe silicate-type and Eu3+-activated Sr3SiO5 and Mg3SiO5 were prepared through the high temperature solid state reaction method under an open atmosphere. DTA/TG analysis was conducted to obtain information about the thermal behaviors of the mixed reactants. Using the DTA/TG results, the sintering process was achieved and the phase properties were characterized by X-ray diffraction (XRD). The effects of the same activator (Eu3+) and co-dopant (Dy3+) on the photoluminescence (PL) properties of the host lattices were investigated by using a photoluminescence spectrometer.

Properties of Low Temperature Fired Ferroelectric/Ferromagnetic Composite Materials

2014 ◽  
Vol 787 ◽  
pp. 313-316
Author(s):  
Dai Nan Zhang ◽  
Wei Wei Lin ◽  
Huai Wu Zhang
Keyword(s):  
Composite Materials ◽  
Low Temperature ◽  
Solid State Reaction Method ◽  
Ceramic Technology ◽  
Electromagnetic Properties ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Sintered Composite

In this paper, Ni0.60Cu0.24Zn0.16Fe2O4/BaTiO3composites of BaTiO3(BT)/NiCuZn (NCZ) with mass ratios (x) equal to 5%, 10%, 15% or 20% were synthesised by a conventional solid-state reaction method and sintered at 900oC to adapt to low temperature co-fired ceramic technology. X-ray diffraction results showed that the composites were composed of BT and NCZ phases. The microstructures of the sintered composite materials were observed and analysed using scanning electron microscopy. The dielectric and magnetic properties of the composites were improved effectively with increasing BaTiO3content. The influences of different compositions on the electromagnetic properties of the composites were investigated.

Effects of B2O3 doping on the dielectric and piezoelectric properties of (K,Na,Li)NbO3-BaZrO3-(Bi,Na)TiO3 ceramics

2021 ◽  
Author(s):  
Nan Wei ◽  
Tomoaki KARAKI ◽  
Tadashi Fujii
Keyword(s):  
Piezoelectric Properties ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Two Phase ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
High Relative Density ◽  
Dielectric And Piezoelectric Properties

Abstract (K,Na,Li)NbO3-BaZrO3-(Bi,Na)TiO3-x B2O3 (abbreviated as KNLN-BZ-BNT-x B2O3) ceramics were prepared by conventional solid state reaction method. The effects of B2O3 content on dielectric and piezoelectric properties of the KNLN-BZ-BNT ceramics have been studied. Based on the identification by X-ray diffraction (XRD), all the samples show a two-phase coexistence zone consisting of rhombohedral (R) and tetragonal (T) phases. For the ceramics with x = 0.5 wt%, the sintering temperature was observed to reduce from 1200 oC to 940 oC, while the samples maintained a high relative density around 97%. Because of the high densification and large grain size, the dielectric and piezoelectric properties were improved. As a result, the ceramics with x = 0.5 wt% sintered at 940 oC exhibited good properties of d 33 = 197 pC/N, k p= 0.29, tan δ = 0.029 and ε r = 1889, together with a Curie temperature (T C) of 222 oC.

Structural and Luminescence Properties of Eu3+ and Dy3+-Doped Magnesium Boro-Tellurite Ceramics

2014 ◽  
Vol 895 ◽  
pp. 269-273
Author(s):  
Nur Zu Ira Bohari ◽  
Rosli Hussin ◽  
Zuhairi Ibrahim ◽  
M.H. Haji Jumali ◽  
Royston Uning ◽  
...  
Keyword(s):  
Solid State ◽  
Ftir Spectroscopy ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Luminescence Properties ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Xrd Studies ◽  
The Eu

Boro-tellurite ceramics with the composition of 60B2O3-10TeO2-30MgO-1Eu2O3-1Dy2O3 in mol % were prepared by solid-state reaction method. The samples were characterized by x-ray diffraction (XRD), photoluminescence (PL) and FTIR spectroscopy. The XRD studies have revealed the presence of MgTe2O5 and MgB6O10.7H2O crystalline as the major and minor phases in these samples. The FTIR spectra reveal the presence of B-O vibrations of B-O-B, BO3 and BO4 bridging oxygen and Te-O stretching modes of Te2O, TeO3 and TeO4 units in the prepared ceramics. The PL peaks were assigned to the Eu3+ transitions 5D07F0 at 580 nm, 5D07F1 at 591 nm and 596 nm, 5D07F2 at 612, 618 and 621 nm, 5D07F3 at 651 nm, and 5D07F4 at 692 nm and 702 nm when excited at 394 nm.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

Sign in / Sign up

Export Citation Format

Share Document