A Study on the Evaluation of the Annual Energy Consumption for a Geothermal Heat Pump System with Open Loop and Closed Loop Ground Heat Exchangers

2017 ◽  
Vol 25 (03) ◽  
pp. 1750024 ◽  
Author(s):  
Samuel Boahen ◽  
Kwang Ho Lee ◽  
Soolyeon Cho ◽  
Jong Min Choi
Keyword(s):  
Energy Consumption ◽  
Closed Loop ◽  
Heat Pumps ◽  
Open Loop ◽  
Geothermal Heat ◽  
Pump System ◽  
Ground Source Heat Pumps ◽  
Heat Pump System ◽  
Ground Heat Exchangers ◽  
Heating And Cooling

Heating and cooling systems contribute greatly to the energy consumption and CO2 emissions of many countries. Ground source heat pumps (GSHP) are promising energy saving systems for residential, commercial or industrial heating or cooling purposes. A method to estimate the energy consumption and CO2 emission of GSHPs is therefore very eminent. This paper reviews the methodology to calculate the energy consumption and CO2 emission of GSHPs. The discussed methodology is then used to compare the energy consumption and CO2 emission of an open-loop and closed-loop GSHP using data from field test. It is observed that the open-loop GSHP saves 28% energy and reduces CO2 by 28% than the closed-loop GSHP in the cooling season. When used for both cooling and heating purposes in the year, the open-loop GSHP saves about 6% energy and reduces about 6% of CO2 emission than the closed-loop GSHP.

DETERMINING THE PROFITABILITY OF GREENHOUSE ELECTROTECHNOLOGIES: A MODELING APPROACH

HortScience ◽  
1994 ◽  
Vol 29 (4) ◽  
pp. 249a-249
Author(s):  
Eric A. Lavoie ◽  
Damien de Halleux ◽  
André Gosselin ◽  
Jean-Claude Dufour
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Water System ◽  
Heat Pumps ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Artificial Lighting ◽  
Hot Air ◽  
Marketable Fruit

The main objective of this research was to produce a simulated model that permitted the evaluation of operating costs of commercial greenhouse tomato growers with respect to heating methods (hot air, hot water, radiant and heat pumps) and the use of artificial lighting for 1991 and 1992. This research showed that the main factors that negatively influence profitability were energy consumption during cold periods and the price of tomatoes during the summer season. The conventional hot water system consumed less energy than the heat pump system and produced marketable fruit yields similar to those from the heat pump system. The hot water system was generally more profitable in regards to energy consumption and productivity. Moreover, investment costs were less; therefore, this system gives best overall financial savings. As for radiant and hot air systems, their overall financial status falls between that of the hot water system and the heat pump. The radiant system proved to be more energy efficient that the hot air system, but the latter produced a higher marketable fruit yield over the 2-year study.

An Economical Analysis on a Solar Greenhouse Integrated Solar Assisted Geothermal Heat Pump System

2005 ◽  
Vol 128 (1) ◽  
pp. 28-34 ◽  
Author(s):  
Onder Ozgener ◽  
Arif Hepbasli
Keyword(s):  
Heat Pump ◽  
Cooling System ◽  
Heat Pumps ◽  
Renewable Energy Resources ◽  
Ahp Method ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Economical Analysis ◽  
Geothermal Heat Pump

The main objective in doing the present study is twofold, namely (i) to review briefly the utilization of geothermally heated greenhouses and geothermal heat pumps in Turkey, since the system studied utilizes both renewable energy resources and (ii) to present the Analytical Hierarchy Process (AHP) as a potential decision making method for use in a greenhouse integrated solar assisted geothermal heat pump system (GISAGHPS), which was installed in the Solar Energy Institute of Ege University, Izmir, Turkey. This investigation may also be regarded as the one of the limited studies on the application of the AHP method to GISAGHPs, as no studies on the GISAGHPS have appeared in the literature. In this context, an economic analysis is performed based on the life cycle costing technique first. The results are then evaluated by applying the AHP method to a study, which is a comparative study on the GISAGHPS and split system. The results indicated that the GISAGHPS is economically preferable to the conventional split heating/cooling system under Turkey’s conditions.

scholarly journals Hybrid Solar Geothermal Heat Pump System Model Demonstration Study

2022 ◽  
Vol 9 ◽  
Author(s):  
Yu-Jin Kim ◽  
Libing Yang ◽  
Evgueniy Entchev ◽  
Soolyeon Cho ◽  
Eun-Chul Kang ◽  
...  
Keyword(s):  
Power Consumption ◽  
Ambient Temperature ◽  
Heat Pump ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Source Temperature ◽  
Heating And Cooling ◽  
Geothermal Heat Pump ◽  
Polygeneration System

In this paper, the development and demonstration of a hybrid solar geothermal heat pump polygeneration system is presented. The poly-generation system has been designed, modeled, and simulated in TRNSYS software environment. Its performance was assessed followed by installation and demonstration at a demo site in Cheongju, Korea. The space heating and cooling load of the building is 13.8 kW in heating mode at an ambient temperature of −10.3°C and 10.6 kW in cooling mode at an ambient temperature of 32.3°C. The simulation data were compared with the field demo data using ISO 13256. The results showed that the model data compare well with the demo data both in heating and cooling modes of operation. At a source temperature of 16.7°C, the heat pump lab performance data-based COPc shows 9.9, while demonstration COPc shows 10.3, thus, representing 4.3% relative error. The heat pump source temperature decreased by 4.0°C from 20.9°C to 16.9°C due to ground heat exchanger coupling and resulted in a COPc increase by 13.3% from 8.5 to 9.8. When compared at the design conditions (outside temperature of 32.3°C), the TRSNYS model overestimated the demonstration site data by 12%, 9.3 vs. 8.1 kW with power consumption of 3.1 vs. 2.2 kW. The hybrid polygeneration system power consumption decreased by 1.2 kW when ambient temperature decreased from 35°C to 25°C.

Development of design guidelines for thermo-active foundations

2017 ◽  
Vol 27 (6) ◽  
pp. 805-817 ◽  
Author(s):  
Byung C. Kwag ◽  
Moncef Krarti
Keyword(s):  
Heat Pump ◽  
Heat Pumps ◽  
Design Guidelines ◽  
Conventional Heating ◽  
Ground Source Heat Pump ◽  
External Energy ◽  
Geothermal Heat ◽  
Ground Source Heat Pumps ◽  
Heating And Cooling ◽  
Ground Source

Ground medium can be utilized as a direct energy source to heat and cool buildings. In particular, ground source heat pump systems take advantage of the year-round mild deep earth temperature without a significant reliance on any external energy sources. However, the high installation cost of ground source heat pumps associated with high drilling cost of vertical boreholes often make these systems less cost-effective compared to conventional heating and cooling systems. Thermo-active foundations can be a viable solution to reduce ground source heat pump high installation costs by embedding heat exchangers within building foundation structures. Compared to ground source heat pumps, only limited analyses and research studies have been reported for thermo-active foundations especially for the US climates. In particular, no specific design guidelines have been reported for thermo-active foundations especially for US climates. In this paper, a simplified design approach was developed and applied for specifying geothermal heat pump size and heat exchanger loop length to meet all or part of building heat and cooling thermal loads. The developed guidelines would thus provide a proper design guide for installation of thermo-active foundations for heating and cooling of both US residential and commercial buildings.

scholarly journals Design and Analysis of a Distributed Water Heat Pump System for Near- and Net-Zero Energy Commercial Buildings

2021 ◽  
Author(s):  
Maudud Hassan Quazi
Keyword(s):  
Natural Gas ◽  
Heat Pump ◽  
Cooling Tower ◽  
Heat Pumps ◽  
Base Case ◽  
Hvac System ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling ◽  
Net Zero

This objective of this project is to determine the energy and environmental potential of distributed common loop water source heat pump system in a near or net-zero commercial office building, which has simultaneous heating and cooling load in winter and shoulder seasons. It is expected that the perimeter zones will have heating demand during those months, while the core zones will have consistent cooling demand throughout the year. The motive is to reclaim the rejected heat from the cooling operation and transfer it to the zones requiring heating. The building under study is a 60,000 ft2 three storey commercial office building, which has private offices along the perimeter, and open work area in the core. In the first part of the analysis, the base building has been modelled and simulated to the minimum requirements of ASHRAE 90.1-Energy Standard for Buildings except Low-Rise Residential Buildings using simulation software eQuest 3.65. The Heating Ventilation and Airconditioning (HVAC) system used is four-pipe fan coil system serving individual zones. The fan coil units use a centralized natural gas boiler and a variable capacity centrifugal chiller as external source of heating and cooling respectively. The base case consumes a total of 524.54 x 1000 kWh of electricity and 1,056 million Btu of natural gas annually. The second part is the modelling and simulation of a proposed case, which uses the same building envelope, occupancy, lighting and equipment as the base case. The HVAC system used is a distributed common loop heat pump system connected to a cooling tower for heat rejection, and a condensing boiler for heat addition. During the occupied hours, when simultaneous cooling and heating loads exist in the building, the cooling zone heat pumps rejects exhaust heat into the common loop, and the heat is subsequently used by the heat pumps operating in heating mode. Using this method, the heat pump system reduces its dependence on the cooling tower and the boiler, which only operate to maintain the loop temperature in an acceptable range. There is 9,510 kWh (1.81%) increase in electricity consumption by proposed case comparing to the base building. Natural gas consumption has been reduced by 353.65 million Btu (33.48%). Annual utility bill has increased by $1,483.00 which is 1.88% higher than the base case. 15.7 tonnes of greenhouse gas can be reduced if the proposed case is adopted.

Modeling and control of heat pump system for battery electric buses

2022 ◽  
pp. 095440702110694
Author(s):  
Rabih Al Haddad ◽  
Hussein Basma ◽  
Charbel Mansour
Keyword(s):  
Energy Consumption ◽  
Weather Conditions ◽  
Heat Pumps ◽  
Operating Conditions ◽  
Coefficient Of Performance ◽  
Cold Weather ◽  
Pump System ◽  
Heat Pump System ◽  
Battery Capacity ◽  
Driving Range

Given the continuous tightening of emissions regulations on vehicles, battery-electric buses (BEB) play an essential role in the transition toward cleaner transport technologies, as they represent the most promising solution to replace diesel buses and reduce their environmental impact in the short term. However, heating the bus cabin leads to a considerable increase in energy consumption under cold weather conditions, which significantly reduces the driving range, given the limited battery capacity. Heat pumps (HP) are the primary heating technology used in BEB for their improved consumption performance compared to other technologies. Therefore, this study aims at optimizing the coefficient of performance (COP) of an HP system in a BEB for maximizing the bus electric driving range under cold weather conditions while maintaining satisfactory thermal comfort levels for passengers. Accordingly, an HP model is developed and integrated into an electric bus model using Dymola. A genetic algorithm (GA) based controller is proposed to find the optimal combination of the HP operating parameters, namely the compressor speed, the air mass flow rate at the inlet of the condenser, and the recirculation rate in order to maximize the system’s COP, and extend the BEB driving at different external temperatures, and as a function of the passengers’ occupancy levels. Results are carried under transient and steady-state operating conditions and show that the proposed GA-based controller saves up to 39% of the HP energy consumption as compared to the conventional HP control strategy, and therefore, enhances the BEB driving range up to 17%.

Performance Prediction of a Sub-Slab Heat Exchanger for Geothermal Heat Pumps

1998 ◽  
Vol 120 (4) ◽  
pp. 282-288 ◽  
Author(s):  
K. Den Braven ◽  
E. Nielson
Keyword(s):  
Soil Temperature ◽  
Heat Pump ◽  
Flow Direction ◽  
Heat Pumps ◽  
Heat Extraction ◽  
Fluid Temperature ◽  
Geothermal Heat ◽  
Pump System ◽  
Pump Operation ◽  
Heat Pump System

A large portion of the installation cost of a ground-coupled heat pump system is for the excavation necessary for ground coil placement. One possible method of reducing this cost is to place the ground coils beneath the slab floor of the building. This configuration of ground coil placement has not been specifically addressed in previous research. Freezing of the soil must be avoided in such a system. To simulate the temperature response of the surrounding soil to heat pump operation, a computer model was developed which incorporates line source theory in the form of a system of rings. The fluid temperature change along the length of the coil was used to determine the distribution of the ground load throughout the ring system. The model includes an adiabatic upper boundary, seasonal soil temperature variation, and thermal interference throughout the system. Using these results, the minimum soil temperature over a season was predicted. Based on these results, design recommendations for ground coil installation are provided based on available area, soil type, heat extraction rate, depth of coil beneath the slab floor, and depth of slab floor below grade. These include recommendations for pipe spacing, flow direction, and a method to determine whether this type of system is feasible for installation in a particular location.

scholarly journals Modeling and Simulation Performance Evaluation of a Proposed Calorimeter for Testing a Heat Pump System

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4589 ◽  
Author(s):  
Amoabeng ◽  
Lee ◽  
Choi
Keyword(s):  
Energy Consumption ◽  
Modeling And Simulation ◽  
Heat Pump ◽  
Energy Efficient ◽  
Residential Buildings ◽  
Test Chamber ◽  
High Energy ◽  
Heat Pumps ◽  
Pump System ◽  
Heating And Cooling

The energy consumption for heating and cooling in the building sector accounts for more than one-third of total energy used worldwide. In view of that, it is important to develop energy efficient cooling and heating systems in order to conserve energy in buildings as well as reduce greenhouse gas emissions. In both commercial and residential buildings, the heat pump has been adopted as an energy efficient technology for space heating and cooling purposes as compared to conventional air conditioning systems. However, heat pumps undergo standard testing, rating, and certification procedures to ascertain their system performance. Essentially, the calorimeter for testing heat pumps has two test chambers to serve as a heat source and heat sink to control and maintain the test conditions required to simulate the heat pump indoor and outdoor units, simultaneously. In air-to-air heat pump units, the conventional calorimeter controls the air temperature and humidity conditions in each test chamber with separate air handling units consisting of a refrigerator, heater, humidifier, and supply fan, which results in high energy consumption. In this study, using dynamic modeling and simulation, a new calorimeter for controlling air conditions in each test chamber is proposed. The performance analysis based on simulation results showed that the newly proposed calorimeter predicted at least 43% energy savings with the use of a heat recovery unit and small refrigerator capacity as compared to the conventional calorimeter that utilized a large refrigerator capacity for all the weather conditions and load capacities that we investigated.

scholarly journals Residential Buildings’ Foundations as a Ground Heat Exchanger and Comparison among Different Types in a Moderate Climate Country

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6287
Author(s):  
Lazaros Aresti ◽  
Paul Christodoulides ◽  
Gregoris P. Panayiotou ◽  
Georgios Florides
Keyword(s):  
Residential Buildings ◽  
Residential Building ◽  
Energy Systems ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Software Environment ◽  
Ground Source Heat Pumps ◽  
Ground Heat Exchangers ◽  
Heating And Cooling ◽  
Air Source Heat Pump

Shallow Geothermal Energy Systems (SGESs) constitute Renewable Energy Systems (RES), which find application in the residential sector through the use of Ground Source Heat Pumps (GSHPs). GSHPs are associated with Ground Heat Exchangers (GHEs), whereby heat is gained/lost through a network of tubes into the ground. GSHPs have failed to flourish in the RES market due to their high initial costs and long payback periods. In this study, the use of Energy Geo-Structure (EGS) systems, namely, the foundation (or energy) piles and the foundation bed of a residential building in Cyprus, was computationally modeled in the COMSOL Multiphysics software. First, the single-houses’ trend in number of units and area in Cyprus was examined and a theoretically typical house with nearly Zero Energy Building (nZEB) characteristics was considered. The heating and cooling loads were estimated in the TRNSYS software environment and used as inputs to investigate the performance of the GSHP/GHE systems. Both systems were shown to exhibit steady performance and high Coefficient of Performance (COP) values, making them an alternative RES solution for residential building integration. Next, the systems were economically evaluated through a comparison with a convectional Air Source Heat Pump (ASHP) system. The economic analysis showed that the cost of the suggested conversions of the foundation elements into GHEs had short payback periods. Consequently, either using the foundation piles or bed as a GHE is a profitable investment and an alternative to conventional RES.

scholarly journals Implementation of a geothermal heat pump system in a solar passive house

2019 ◽  
Vol 85 ◽  
pp. 07014
Author(s):  
Gheorghe Ilisei ◽  
Tiberiu Catalina ◽  
Marian Alexandru ◽  
Robert Gavriliuc
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Passive House ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Major Index ◽  
Passive Houses

Underground energy sources are becoming increasingly popular and now geothermal heat pumps are frequently used to heat/cool different types of buildings, including for solar passive houses. This article aims at giving a contribution in the development of the thermal modelling of borehole heat storage systems, investigating the possibility of a GSHP (ground source heat pump) implementation with vertical boreholes in a solar passive house. A case study analysing a residential solar passive house is presented as a suitable modelling tool for the estimation of the thermal behaviour of GSHP systems by combining the outcome from different modelling programs. The software DesignBuilder, Earth Energy Designer and a sizing method for borehole’s length are used for producing the numerical results. The results highlight that the length of the borehole, a major index in estimating the system’s cost, is directly influenced by fundamental variables like thermal conductivity of grout or soil. Additionally, correlations between these parameters and the coefficient of performance of GSHP were made. Furthermore, the length of borehole is very important as it is responsible for almost half of the total installation cost and triggered a difference in electricity consumption of the GSHP up to 14%.

Sign in / Sign up

Export Citation Format

Share Document