scholarly journals In Situ Stress Measurements on Thin Film Au Positive Electrode during the First Discharge of Li-O2 Batteries

Author(s):  
Hannah Dykes ◽  
Rosy . ◽  
Daniel Sharon ◽  
Malachi Noked ◽  
Omer Ozgur Capraz

Abstract The formation and growth of the Li2O2 discharge product impacts the reversibility of the oxygen evolution and reduction reactions in Li-O2 batteries which may lead to a shorter cycle life. A clear understanding of the surface reactions and the growth mechanism of Li2O2 requires probing dynamic changes on the surface of the positive electrodes in situ during the discharge of a Li-O2 battery. To investigate this, we establish an experimental system by adopting a multi-beam optical sensor (MOS) and developing a custom-made battery cell. First, the accuracy and reliability of the system was demonstrated by analyzing the stress accumulation on the Au negative electrode during Li plating/stripping, and the results were consistent with an earlier single-beam scanning deflectometry report. Then, the Li-O2 battery was discharged in LiNO3 in diglyme electrolyte by applying either linear sweep voltammetry or by applying constant current under an O2 environment. Control experiments in Argon-saturated electrolytes indicate surface stress generation due to charge-induced stress. The stress generation on Au positive electrode is attributed to the formation of Li2O2 reaction products on the Au surface and charge-induced stress.

2010 ◽  
Vol 89-91 ◽  
pp. 503-508 ◽  
Author(s):  
J. Sheng ◽  
U. Welzel ◽  
Eric J. Mittemeijer

The stress evolution during diffusion annealing of Ni-Cu bilayers (individual layer thicknesses of 50 nm) was investigated employing ex-situ and in-situ X-ray diffraction measurements. Annealing at relatively low homologous temperatures (about 0.3 - 0.4 Tm) for durations up to about 100 hours results in considerable diffusional intermixing, as demonstrated by Auger-electron spectroscopy investigations (in combination with sputter-depth profiling). In addition to thermal stresses due to differences of the coefficients of thermal expansion of layers and substrate, tensile stress con-tributions in the sublayers arise during the diffusion anneals. The obtained stress data have been discussed in terms of possible mechanisms of stress generation. The influence of diffusion on stress development in the sublayers of the diffusion couple during heating and isothermal annealing was investigated by comparing stress changes in the bilayer system with corresponding results obtained under identical conditions for single layers of the components in the bilayer system. The specific residual stresses that emerge due to diffusion between the (sub)layers in the bilayer could thereby be identified.


ChemInform ◽  
1989 ◽  
Vol 20 (37) ◽  
Author(s):  
R. J. BONES ◽  
D. A. TEAGLE ◽  
S. D. BROOKER ◽  
F. L. CULLEN

2015 ◽  
Vol 3 (20) ◽  
pp. 10976-10989 ◽  
Author(s):  
B. Mortemard de Boisse ◽  
J.-H. Cheng ◽  
D. Carlier ◽  
M. Guignard ◽  
C.-J. Pan ◽  
...  

O3–Na0.77Mn1/3Fe2/3O2 was studied by in situ XRPD. The system undergoes several structural transitions from 1.5 V to 4.3 V: O′3 → O3 → P3 → “X”.


Author(s):  
Robert R. Richardson ◽  
Christoph R. Birkl ◽  
Michael A. Osborne ◽  
David A. Howey

Accurate on-board capacity estimation is of critical importance in lithium-ion battery applications. Battery charging/discharging often occurs under a constant current load, and hence voltage vs. time measurements under this condition may be accessible in practice. This paper presents a novel diagnostic technique, Gaussian Process regression for In-situ Capacity Estimation (GP-ICE), which is capable of estimating the battery capacity using voltage vs. time measurements over short periods of galvanostatic operation. The approach uses Gaussian process regression to map from voltage values at a selection of uniformly distributed times, to cell capacity. Unlike previous works, GP-ICE does not rely on interpreting the voltage-time data through the lens of Incremental Capacity (IC) or Differential Voltage (DV) analysis. This overcomes both the need to differentiate the voltage-time data (a process which amplifies measurement noise), and the requirement that the range of voltage measurements encompasses the peaks in the IC/DV curves. Rather, GP-ICE gives insight into which portions of the voltage range are most informative about the capacity for a particular cell. We apply GP-ICE to a dataset of 8 cells, which were aged by repeated application of an ARTEMIS urban drive cycle. Within certain voltage ranges, as little as 10 seconds of charge data is sufficient to enable capacity estimates with ∼ 2% RMSE.


2021 ◽  
Vol 54 (1) ◽  
pp. 371-375
Author(s):  
Paul Monceyron Røren ◽  
Kristoffer W. B. Hunvik ◽  
Vegard Josvanger ◽  
Ole Tore Buseth ◽  
Jon Otto Fossum

A sample cell for powder X-ray diffraction studies with in situ applied pressure and control of temperature is demonstrated. The cell is based on a previously reported design and consists of a glass or quartz capillary glued into a Swagelok weld gland; this configuration can hold up to 100 bar (1 bar = 100 kPa). The cell is placed in contact with a copper plate for control of temperature between −30 and 200°C. This is achieved by Peltier elements, heat cartridges and a refrigerated circulating bath. This work mainly focuses on the temperature control system. Commissioning tests were performed in a custom-made small/wide-angle X-ray diffractometer at the Norwegian University of Science and Technology. The system is easily portable to synchrotron facilities.


2020 ◽  
Author(s):  
Fernando Medina Ferrer ◽  
Kathryn Hobart ◽  
Jake V. Bailey

ABSTRACTMicrobial precipitation of calcium carbonate has diverse engineering applications, from building and soil restoration, to carbon sequestration. Urease-mediated ureolysis and CO2 (de)hydration by carbonic anhydrase (CA) are known for their potential to precipitate carbonate minerals, yet many microbial community studies rely on marker gene or metagenomic approaches that are unable to determine in situ activity. Here, we developed fast and cost-effective tests for the field detection of urease and CA activity using pH-sensitive strips inside microcentrifuge tubes that change color in response to the reaction products of urease (NH3) and CA (CO2). Samples from a saline lake, a series of calcareous fens, and ferrous springs were assayed in the field, finding relatively high urease activity in lake samples, whereas CA activity was only detected in a ferrous spring. Incubations of lake microbes with urea resulted in significantly higher CaCO3 precipitation compared to incubations with a urease inhibitor. Therefore, the rapid assay indicated an on-site active metabolism potentially mediating carbonate mineralization. Field urease and CA activity assays complement molecular approaches and facilitate the search for carbonate-precipitating microbes and their in situ activity, which could be applied toward agriculture, engineering and carbon sequestration technologies.


2013 ◽  
Vol 38 (2) ◽  
pp. 142-150 ◽  
Author(s):  
LE Tam ◽  
P Bahrami ◽  
O Oguienko ◽  
H Limeback

SUMMARY Purpose Although damage to the structural integrity of the tooth is not usually considered a significant problem associated with tooth bleaching, there have been some reported negative effects of bleaching on dental hard tissues in vitro. More studies are needed to determine whether the observed in vitro effects have practical clinical implications regarding tooth structural durability. Objectives This in situ study evaluated the effect of 10% and 15% carbamide peroxide (CP) dental bleach, applied using conventional whitening trays by participants at home, on the fracture toughness of dentin. Methods Ninety-one adult volunteers were recruited (n ≈ 30/group). Compact fracture toughness specimens (approximately 4.5 × 4.6 × 1.7 mm) were prepared from the coronal dentin of recently extracted human molars and gamma-radiated. One specimen was fitted into a prepared slot, adjacent to a maxillary premolar, within a custom-made bleaching tray that was made for each adult participant. The participants were instructed to wear the tray containing the dentin specimen with placebo, 10% CP, or 15% CP treatment gel overnight for 14 nights and to store it in artificial saliva when not in use. Pre-bleach and post-bleach tooth color and tooth sensitivity were also evaluated using ranked shade tab values and visual analogue scales (VASs), respectively. Within 24–48 hours after the last bleach session, the dentin specimens were tested for fracture toughness using tensile loading at 10 mm/min. Analysis of variance, Kruskal-Wallis, χ2, Tukey's, and Mann-Whitney U tests were used for statistical analysis. The level of significance was set at p<0.05 for all tests, except for the Mann-Whitney U tests, which used a Bonferroni correction for post hoc analyses of the nonparametric data (p<0.017). Results The placebo, 10% CP, and 15% CP groups contained 30, 31, and 30 participants, respectively. Mean fracture toughness (+ standard deviation) for the placebo, 10% CP, and 15% CP groups were 2.3 ± 0.9, 2.2 ± 0.7, and 2.0 ± 0.5 MPa*m1/2 respectively. There were no significant differences in mean fracture toughness results among the groups (p=0.241). The tooth sensitivity VAS scores indicated a significantly greater incidence (p=0.000) and degree of tooth sensitivity (p=0.049 for VAS change and p=0.003 for max VAS) in the bleach groups than in the placebo group. The color change results showed generally greater color change in the bleach groups than in the placebo group (p=0.008 for shade guide determination and p=0.000 for colorimeter determination). Conclusions There were no significant differences in in situ dentin fracture toughness results among the groups. The results of this study provide some reassurance that dentin is not overtly weakened by the bleaching protocol used in this study. However, the lack of a statistically significant difference cannot be used to state that there is no effect of bleach on dentin fracture toughness.


Sign in / Sign up

Export Citation Format

Share Document