Room-Temperature Fabrication of NiO Films for Electrochromic Application by Electrophoretic Deposition (EPD): From Single Layers to Devices

2019 ◽  
Vol 8 (9) ◽  
pp. Q171-Q177 ◽  
Author(s):  
Zhisheng Wu ◽  
Mingya Li ◽  
Xiaoqiang Wang ◽  
Lei Wu ◽  
Jie Xiong ◽  
...  
2007 ◽  
Vol 1031 ◽  
Author(s):  
Nathanael Smith ◽  
Kevin J Emmett ◽  
Sandra J Rosenthal

AbstractCdSe nanocrystals chemically linked to nanocrystalline titanium dioxide substrates form a promising material for nanostructured photovoltaic devices. The usual method for attaching the nanocrystals to the titanium dioxide substrate is by means of a linking molecule (such as mercaptopropionic acid) or in-situ growth. In this paper, we report the use of an alternative technique, electrophoretic deposition (EPD), to directly deposit already formed CdSe nanocrystals onto the substrate. In EPD, a voltage is established between two electrodes that are immersed in a solution of nanocrystals. At room temperature, a fraction of the nanocrystals are thermally charged, and these charged nanocrystals migrate to the electrodes and adhere to the surface. A significant advantage of EPD over the use of linking molecules is the speed with which the nanocrystals are deposited: EPD takes only a few minutes, compared to the several hours required for the alternative techniques. Additionally, we have fabricated initial photovoltaic devices based on electrophoretically deposited CdSe nanocrystals on a planar TiO2 thin film.


2017 ◽  
Vol 17 (2) ◽  
pp. 18-28 ◽  
Author(s):  
M. Bartmanski

AbstractThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed by drying at room temperature for 24 h and heating at 800°C for 1 h in vacuum. The thickness of the nanoHAp and nanoHAp/nanoAg coatings was found as of about 5 μm. The corrosion behavior tests made by potentiodynamic methods brought out slightly higher values of corrosion current for nanoHAp coatings and nanoHAp/nanoAg coatings as compared to the reference Ti13Zr13Nb specimen. The nanohardness of the nanoHAp coatings achieved 0.020 ± 0.004 GPa and of the nanoHAp/nanoAg coatings 0.026 ± 0.012 GPa. Nanoscratch test of the nanoHAp and nanoHAp/nanoAg coatings revealed an increased Critical Friction (mN) in the presence of nanosilver particles. The wettability angles decreased for nanoHAp/nanoAg coatings comparing to pure nanoHAp coatings on titanium alloy.


Coatings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 87 ◽  
Author(s):  
Jui-Yang Chang ◽  
Ying-Chung Chen ◽  
Chih-Ming Wang ◽  
You-Wei Chen

In this study: various amounts of Li2CO3 powders were mixed into NiO powders to fabricate the Li- added NiO (NiO:Li) targets. The electrochromic films of LiNiO were deposited on ITO glasses at room temperature (R.T.) by RF magnetron sputtering. The thicknesses of electrochromic LiNiO films were kept about 200 nm. The ECD device was constructed with structure of Glass/ITO/ LiNiO /Gel-electrolyte/ITO/Glass. The results indicated that the optimal electrochromic characteristics of Li0.16Ni0.58O thin films could be obtained by 10 wt% Li2CO3 added NiO target. The optimized characteristics of ECDs could be achieved with the intercalation charge (Q) of 11.93 mC/cm2, the optical density (ΔOD) of 0.38, the transmittance change (ΔT) of 44.1%, and the coloring efficiency (η) of 31.8 cm2/C at the wavelength of 550 nm by setting voltage of 3.2V. The results demonstrate that the doping of Li+ ions into NiO films can effectively enhance the characteristics of ECD devices. The reason may due to the increased amount of charge stored in the electrochromic devices (ECDs).


2009 ◽  
Vol 1214 ◽  
Author(s):  
Naoki Shiraishi ◽  
Yushi Kato ◽  
Hideki Arai ◽  
Nobuo Tsuchimine ◽  
Susumu Kobayashi ◽  
...  

AbstractNiO is a typical material for new p-type oxide semiconductors. Conductivity of NiO can be raised with Li+ doping. In case of Li-heavy doping, we can obtain LixNiO2(0.5< × <1.0). Recently the importance of LiNiO2 has been increased as an electrode material for rechargeable lithium cells.In this work, we tried to fabricate a novel NiO material with Li+-heavily doped by applying the pulsed laser-induced room temperature (R.T.) film process. Previously, we have succeeded in the epitaxial growth of various oxide thin films at R.T. such as Sn-doped In2O3 transparent electrodes [1]. Although the many studies have been made on the deposition of NiO epitaxial thin film at low temperatures [2], there are few reports on fabrication and the conductive characteristic for Li-heavily doped NiO epitaxial films. The film deposition at R.T., which is the unequilibrium vapor phase process, is expected to result in different crystal structure and characteristics from the films grown at high-temperatures.A composition-adjusted thin film of LixNi1-xO(0.10< × <0.40) was deposited on a sapphire (α-Al2O3)(0001) or MgO(100) substrates by pulsed laser deposition (PLD) technique in 10−6 Torr of oxygen at R.T. and the high temperatures of 350 and 515°C. Crystalline properties of thin films deposited at R.T. or high temperatures were examined using reflection high energy electron diffraction (RHEED) and X-ray diffraction. For the Li-heavily doped NiO films(x>0.30) grown at R.T., a clear streak RHEED pattern showing epitaxial growth was observed. But the Li-heavily doped NiO films grown at high temperatures, exhibited the ring RHEED pattern, which indicates the policrystal growth of films. Electric conductivity of various Li-doped NiO thin films deposited at R.T. or high temperatures on sapphire (0001) substrates were measured by two-probe method. The interesting results were obtained that conductivity of the film was increased remarkably with an increase of Li-doping for R.T. deposition, but was not changed so much regardless of Li-doping for high-temperature depositions.


2015 ◽  
Vol 1131 ◽  
pp. 135-138
Author(s):  
Emmanuel A. Florido ◽  
Aniceto B. Maghirang

Zinc oxide (ZnO) films on graphite substrate were fabricated using electrophoretic deposition (EPD) method. The effect of concentration and applied voltage in EPD were determined in which the mass of deposited ZnO depends on the applied voltage and not on the concentration. Sensitization of film with palladium chloride (PdCl2) was done through dipping method. The optimum number of dipping is 20. The sensitized samples were subjected to annealing at 100 °C for 30 minutes. The morphology of the films was analyzed through scanning electron microscopy (SEM) which showed the porosity and thickness of the samples. The IV characterization of the samples was done via four-point probe method and the resistivity and resistance were calculated. The resistivity and resistance were found to be lowest in graphite substrate while the films with palladium (Pd) showed lower values of resistivity and resistance than the films without palladium. . A three trial gas sensing experiment at room temperature was performed in which the response of the film to butane/propane gas (LPG) was tested and showed that it successfully sensed the gas. The sample with Pd deposited at the highest applied voltage showed the best gas response and response time among the other samples.Zinc Oxide (ZnO) films on graphite substrate were fabricated using Electrophoretic Deposition (EPD) method. The effect of concentration and applied voltage in EPD were determined in which the mass of deposited ZnO depends on the applied voltage and not on the concentration. Sensitization of film with Palladium Chloride (PdCl2) was done through dipping method. The optimum number of dipping is 20. The sensitized samples were subjected to annealing at 100 °C for 30 minutes. The morphology of the films was analyzed through Scanning Electron Microscopy (SEM) which showed the porosity and thickness of the samples. The IV characterization of the samples was done via four-point probe method and the resistivity and resistance were calculated. The resistivity and resistance was found to be lowest in graphite substrate while the films with palladium (Pd) showed lower values of resistivity and resistance than the films without palladium. . A three trial gas sensing experiment at room temperature was performed in which the sensitivity of the film to butane/propane gas (LPG) was tested and showed that it successfully sensed the gas. The sample with Pd deposited at the highest applied voltage showed the best sensitivity and response time among the other samples.


2013 ◽  
Vol 22 (5) ◽  
pp. 327-332 ◽  
Author(s):  
Young-Chul Jung ◽  
Gyohun Koo ◽  
Jae-Sung Lee ◽  
Sung-Ho Hahm ◽  
Yong Soo Lee
Keyword(s):  

2012 ◽  
Vol 706-709 ◽  
pp. 617-622
Author(s):  
Rong Ma ◽  
Igor Zhitomirsky

Electrophoretic deposition method has been developed for the fabrication of organic-inorganic composite films, containing bioglass and hydroxyapatite in a hyaluronic acid matrix. The film composition and deposition yield were varied by variation of the electrochemical bath composition and deposition time. The films were studied by scanning electron microscopy, thermogravimetric analysis and X-ray diffraction methods. The deposition method offers the advantages of room temperature processing and allows the fabrication of composite films for biomedical applications.


2007 ◽  
Vol 336-338 ◽  
pp. 87-90
Author(s):  
Ya Lu Ma ◽  
Yu Zhang ◽  
Hong Long Zhu

Barium titanate ferroelectric films on Pt substrates were fabricated by electrophoretic deposition (EPD) technique. The barium titanate films sintered at different temperature (600°C, 900°C, 1050°C, 1150°C, 1200°C) for 2h, which were prepared via repeated EPD-sintering route 2~3 times were sufficiently dense and had uniform microstructure. The XRD pattern and SEM microphotography have been measured in order to investigate the effects of the final annealing temperature on the phase compositions and microstructure of the film. The experiment results showed that barium titanate films were crystallized into the tetragonal phase at 1050°C and above. The room temperature dielectric constant (ε) and loss tangent (tanδ) at 1kHz were respectively determined for different samples sintered at 600°C, 900°C, 1050°C, 1150°C and 1200°C. Both ε and tanδ showed anomaly peaks at 125°C. The results showed that typical BaTiO3 films sintered at 1050°C having higher dielectric constant (ε=2300) and lower dielectric loss (tanδ=0.02). The room temperature remanant polarization (Pr) and coercive field (EC) were found to be 1.9μC/cm2 and 35kV/cm, respectively.


Sign in / Sign up

Export Citation Format

Share Document