scholarly journals Hydrothermal Synthesis ofSnO2Nanostructures with Different Morphologies and Their Optical Properties

2011 ◽  
Vol 2011 ◽  
pp. 1-10 ◽  
Author(s):  
Lin Tan ◽  
Lihong Wang ◽  
Yude Wang
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Sol Gel ◽  
Hollow Spheres ◽  
Sodium Dodecyl ◽  
X Ray Diffraction ◽  
Room Temperature Photoluminescence ◽  
Tin Chloride ◽  
Transmission Electron ◽  
High Resolution Tem

SnO2hollow spheres and nanorods were prepared by an aqueous sol-gel route involving the reaction of tin chloride and sodium dodecyl sulphate (SDS) in hexanol and heptane under the different hydrothermal treating temperature and time. X-ray diffraction (XRD) spectra, Fourier transformed infrared (FTIR) spectrum, scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM) and Raman spectroscopy were used to examine the morphology and microstructure to find out the cause. The result indicates that the products are hollow spheres with diameters of approximately 200–900 nm and shell thickness of 60–70 nm via hydrothermal treating at 160°C and one-dimensional rod-like nanostructures with diameters of approximately 20–40 nm and lengths of 100–300 nm via hydrothermal treating at 180 and 200°C, respectively. Room-temperature photoluminescence (PL) properties were investigated under the excitation of 275 nm. The samples exhibited the emission peaks of room-temperature photoluminescence.

Facile Sol-Gel Synthesis of Mesoporous TiO2 in Ionic Liquids

2013 ◽  
Vol 389 ◽  
pp. 53-56
Author(s):  
Shu Guo ◽  
Sheng Xu Lu ◽  
Hui Ding ◽  
Zai Feng Shi
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Sol Gel ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carboxylate Groups ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Sol Gel Synthesis

The mesoporous TiO2 particles was conveniently prepared in a room temperature ionic liquid (RTILs) of 1, 3-di-(3-propionyloxy) imdazolium tetrafluoroborate [DiprCOOBF4 system. The obtained materials were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and N2 adsorptiondesorption analysis. XRD patterns revealed that only rutile phase is formed in the RTILs. The TEM micrographs as well as N2 adsorptiondesorption measurements show that the prepared products exhibited wormlike pore structures. The FTIR (Fourier Transform Infrared Spectra) demonstrate the carboxylate groups attach via bidentate or bridging coordination to the TiO2 surface.

Synthesis, characterization, and photocatalytic properties of pyrochlore Bi2Ti2O7 nanotubes

2006 ◽  
Vol 21 (11) ◽  
pp. 2941-2947 ◽  
Author(s):  
Hongjun Zhou ◽  
Tae-Jin Park ◽  
Stanislaus S. Wong
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Bulk Sample ◽  
X Ray Diffraction ◽  
Alumina Template ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
High Resolution Tem

Bismuth titanate (Bi2Ti2O7) nanotubes were successfully synthesized with an alumina template-based sol-gel technique. As-synthesized nanotubes are smooth and uniform with diameters ranging from 180 to 330 nm and lengths varying from 7 to 12 μm. Extensive characterization of as-prepared samples has been performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), energy-dispersive x-ray spectroscopy (EDS), and selected-area electron diffraction (SAED). Photocatalytic studies indicate that as-prepared nanotubes possess higher photocatalytic activity than the corresponding bulk sample prepared without the use of an alumina template.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Synthesis, Characterization, and Microwave Absorption Properties of SrFe12O19 Ferrites and FeNi3 Nanoplatelets Composites

2010 ◽  
Vol 148-149 ◽  
pp. 893-896 ◽  
Author(s):  
Ze Yang Zhang ◽  
Xiang Xuan Liu ◽  
You Peng Wu
Keyword(s):  
Electron Microscopy ◽  
Microwave Absorption ◽  
Composite Coatings ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Absorption Properties ◽  
Filling Fraction ◽  
Microwave Absorption Properties ◽  
Phase Reduction ◽  
Transmission Electron

M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were successfully prepared by the sol-gel method and solution phase reduction method, respectively. The crystalline and morphology of particles were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The composite coatings with SrFe12O19 ferrites and FeNi3 nanoplatelets in polyvinylchloride matrix were prepared. The microwave absorption properties of these coatings were investigated in 2-18GHz frequency range. The results showed that the M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were obtained and they presented irregular sheet shapes. With the increase of the coating thickness, the absorbing peak value moves to the lower frequency. The absorbing peak values of the wave increase along with the increasing of the content of FeNi3 nanoplatelets filling fraction. When 40% SrFe12O19 ferrites is doped with 20% mass fraction FeNi3 nanoplatelets to prepare composite with 1.5mm thickness, the maximum reflection loss is -24.8 dB at 7.9GHz and the -10 dB bandwidth reaches 3.2GHz.

Synthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons

2010 ◽  
Vol 97-101 ◽  
pp. 4213-4216
Author(s):  
Jian Xiong Liu ◽  
Zheng Yu Wu ◽  
Guo Wen Meng ◽  
Zhao Lin Zhan
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Vapour Deposition ◽  
Chemical Vapour ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Ceramic Boat

Novel single-crystalline SnO2 zigzag nanoribbons have been successfully synthesized by chemical vapour deposition. Sn powder in a ceramic boat covered with Si plates was heated at 1100°C in a flowing argon atmosphere to get deposits on a Si wafers. The main part of deposits is SnO2 zigzag nanoribbons. They were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and selected-area electron diffraction (SAED). SEM observations reveal that the SnO2 zigzag nanoribbons are almost uniform, with lengths near to several hundred micrometers and have a good periodically tuned microstructure as the same zigzag angle and growth directions. Possible growth mechanism of these zigzag nanoribbons was discussed. A room temperature PL spectrum of the zigzag nanoribbons shows three peaks at 373nm, 421nm and 477nm.The novel zigzag microstructures will provide a new candidate for potential application.

Evaluation Humidity Sensing Properties of Graphene/HS-TiO2 Nanocomposites

2021 ◽  
Vol 21 (10) ◽  
pp. 5143-5149
Author(s):  
Zhen Zhu ◽  
Wang-De Lin
Keyword(s):  
Room Temperature ◽  
Response Times ◽  
Sol Gel ◽  
Hollow Spheres ◽  
High Sensitivity ◽  
Humidity Sensing ◽  
X Ray ◽  
Transmission Electron ◽  
Recovery Times ◽  
Relative Humidity Range

This paper reports on a nanocomposite synthesized by sol–gel procedure comprising graphene sheets with hollow spheres of titanium dioxide (G/HS-TiO2) with varying weight percentages of graphene for the purpose of humidity sensors. The surface morphology of the nanocomposite was characterized using transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). The structural properties were examined using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). The response to 12–80% RH at room temperature exhibited sensitivity (S = 135). However, the relative humidity range of 12–90% at room temperature exhibited higher sensitivity (S = 557). Sensors fabricated using the proposed nanocomposite exhibited high sensitivity to humidity, high stability, rapid response times, and rapid recovery times with hysteresis error of less than 1.79%. These results demonstrate the outstanding potential of his material for the monitoring of atmospheric humidity. This study also sought to elucidate the mechanisms underlying humidity sensing performance.

scholarly journals Magnetic PbFe12O19-TiO2 nanocomposites and their photocatalytic performance in the removal of toxic pollutants

2018 ◽  
Vol 41 (3-4) ◽  
pp. 53-62 ◽  
Author(s):  
Behnaz Lahijani ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Photocatalytic Effect ◽  
Transmission Electron ◽  
Ultraviolet Light Irradiation

Abstract In this work, the PbFe12O19 nanoparticles were prepared by the simple and optimized precipitation method with different organic surfactants and capping agents. In the next step, the TiO2 nanoparticles were synthesized using the sol-gel method. At the final step, the PbFe12O19-TiO2 nanocomposites were prepared via the sol-gel method. The effect of the precipitating agent on the morphology and particle size of the products was investigated. The prepared products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The results obtained by the vibrating sample magnetometer show the magnetic properties of the ferrite nanostructures. The photocatalytic effect of the PbFe12O19-TiO2 nanocomposite on the elimination of the azo dyes (acid black, acid violet and acid blue) under ultraviolet light irradiation was evaluated. The results indicate that the prepared nanocomposites have acceptable magnetic and photocatalytic performance.

The Evaporative Decomposition of Solutions Method (Eds) for the Production of Ultrafine Y1Ba2Cu3O7 from Nitrate and Mixed Anion Precursor Solutions

1989 ◽  
Vol 169 ◽  
Author(s):  
Rollin E. Lakis ◽  
Sidney R. Butler
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Barium Carbonate ◽  
Hollow Spheres ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

AbstractY1Ba2Cu3O7 has been prepared by the evaporative decomposition of solutions method. Nitrate and mixed anion solutions were atomized and decomposed at temperatures ranging from 300°C to 950°C. The resulting materials have been characterized using x-ray powder diffraction, Thermal Gravimetric Analysis (TGA), particle size analysis, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The powder consists of 0.3 micron agglomerated hollow spheres with a primary particle size of 0.06 micron. TGA and x-ray diffraction indicate the presence of barium nitrate and barium carbonate due to incomplete decomposition and/or product contamination by the process environment.

New method for the production of bulk amorphous materials of Nd–Fe–B alloys

2005 ◽  
Vol 20 (3) ◽  
pp. 563-566 ◽  
Author(s):  
Tetsuji Saito ◽  
Hiroyuku Takeishi ◽  
Noboru Nakayama
Keyword(s):  
Electron Microscopy ◽  
Amorphous Materials ◽  
Room Temperature ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons

We report a new compression shearing method for the production of bulk amorphous materials. In this study, amorphous Nd–Fe–B melt-spun ribbons were successfully consolidated into bulk form at room temperature by the compression shearing method. X-ray diffraction and transmission electron microscopy studies revealed that the amorphous structure was well maintained in the bulk materials. The resultant bulk materials exhibited the same magnetic properties as the original amorphous Nd–Fe–B materials.

Sign in / Sign up

Export Citation Format

Share Document