scholarly journals Green Synthesis of Feather-Shaped MoS2/CdS Photocatalyst for Effective Hydrogen Production

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Yang Liu ◽  
Hongtao Yu ◽  
Xie Quan ◽  
Shuo Chen
Keyword(s):  
Electron Microscopy ◽  
Hydrogen Production ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance ◽  
Sulfur Source ◽  
X Ray ◽  
Transmission Electron ◽  
Microscopy Images ◽  
Effective Hydrogen ◽  
Better Than

MoS2/CdS photocatalyst was fabricated by a hydrothermal method for H2production under visible light. This method used low toxic thiourea as a sulfur source and was carried out at 200°C. Thus, it was better than the traditional methods, which are based on an annealing process at relatively high temperature (above 400°C) using toxic H2S as reducing agent. Scanning electron microscopy and transmission electron microscopy images showed that the morphologies of MoS2/CdS samples were feather shaped and MoS2layer was on the surface of CdS. The X-ray photoelectron spectroscopy testified that the sample was composed of stoichiometric MoS2and CdS. The UV-vis diffuse reflectance spectra displayed that the loading of MoS2can enhance the optical absorption of MoS2/CdS. The photocatalytic activity of MoS2/CdS was evaluated by producing hydrogen. The hydrogen production rate on MoS2/CdS reached 192 μmol·h−1. This performance was stable during three repeated photocatalytic processes.

Hydrothermal Synthesis and Photocatalytic Properties of Flower-Like CdS Nanostructures

2011 ◽  
Vol 335-336 ◽  
pp. 460-463 ◽  
Author(s):  
Hong Mei Wang ◽  
Da Peng Zhou ◽  
Yuan Lian ◽  
Ming Pang ◽  
Dan Liu
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Uv Light ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Transmission Electron ◽  
Cds Nanostructures

Hexagonal flower-like CdS nanostructures were successfully synthesized through a facile hydrothermal method with thiourea as sulfur source. By combining the results of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the structural and morphological characterizations of the products were performed. The photocatalytic activity of CdS nanostructures had been tested by degradation of Rhodamine B (RB) under UV light compared to commercial CdS powders, which indicated that the as-syntherized CdS nanostructures exhibited enhanced photocatalytic activity for degradation of RB. The possible growth mechanism of CdS nanostructures was proposed in the end.

SYNTHESIS AND FIELD EMISSION PROPERTIES OF SnS2 AND In-DOPED SnS2 WITH HIERARCHICAL STRUCTURE

NANO ◽  
2011 ◽  
Vol 06 (05) ◽  
pp. 489-496 ◽  
Author(s):  
H. X. ZHONG ◽  
C. X. WANG
Keyword(s):  
Electron Microscopy ◽  
Field Emission ◽  
Photoelectron Spectroscopy ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Hydrothermal Route ◽  
X Ray ◽  
Emission Properties ◽  
Field Emission Properties ◽  
Transmission Electron

A simple hydrothermal route was employed to prepare flower-like SnS2 and In -doped SnS2 by using biomolecular L-cysteine as sulfur source. The synthetic samples were characterized by X-ray diffraction, scanning electron microscopy, high resolution transmission electron microscopy, X-ray photoelectron spectroscopy and Raman spectroscopy in detail. Furthermore, the field emission from both the materials was investigated, it was found that both of them have excellent field emission properties, and the doped In has enhanced the field emission properties.

Biomolecule-Assisted Synthesis of Ribbon-Like Sb2S3 Nanostructure

2010 ◽  
Vol 97-101 ◽  
pp. 2144-2147
Author(s):  
Xin Yu Yang ◽  
Wei Dong Xiang ◽  
Xi Yan Zhang ◽  
Hai Tao Liu
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sulfur Source ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
High Resolution Tem ◽  
Scanning Electron

L-Cystine was successfully used as a novel kind of sulfur source to synthesize the nanostructure of ribbon-like Sb2S3. The nanoribbons were usually tens of micronmeters in length, typically 100-300 nm in width. The nanostructure of ribbon-like Sb2S3 were examined using diverse techniques including X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), selected-area electron diffraction, and high-resolution TEM.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

Characterization of columns grown during KrF laser micromachining of Al2O3–TiC ceramics

2003 ◽  
Vol 18 (5) ◽  
pp. 1123-1130 ◽  
Author(s):  
V. Oliveira ◽  
R. Vilar
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Laser Pulses ◽  
Formation Mechanisms ◽  
X Ray ◽  
Reducing Conditions ◽  
Transmission Electron ◽  
Column Formation ◽  
Krf Laser

This paper aims to contribute to the understanding of column formation mechanisms in Al2O3–TiC ceramics micromachined using excimer lasers. Chemical and structural characterization of columns grown in Al2O3–TiC composite processed with 200 KrF laser pulses at 10 J/cm2 was carried out by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, and x-ray diffraction analysis. Fully developed columns consist of a core of unprocessed material surrounded by an outer layer of Al2TiO5, formed in oxidizing conditions, and an inner layer, formed in reducing conditions, composed of TiC and Al3Ti or an AlTi solid solution. Possible mechanisms of column formation are discussed.

scholarly journals Aluminum Nitride-Silicon Carbide Alloy Crystals Grown on SiC Substrates by Sublimation

2005 ◽  
Vol 10 ◽  
Author(s):  
Z. Gu ◽  
L. Du ◽  
J.H. Edgar ◽  
E.A. Payzant ◽  
L. Walker ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Original Source ◽  
X Ray ◽  
Alloy Crystal ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
Vapor Distribution ◽  
Uniform Composition

AlN-SiC alloy crystals, with a thickness greater than 500 µm, were grown on 4H- and 6H-SiC substrates from a mixture of AlN and SiC powders by the sublimation-recondensation method at 1860-1990 °C. On-axis SiC substrates produced a rough surface covered with hexagonal grains, while 6H- and 4H- off-axis SiC substrates with different miscut angles (8° or 3.68°) formed a relatively smooth surface with terraces and steps. The substrate misorientation ensured that the AlN-SiC alloy crystals grew two dimensionally as identified by scanning electron microscopy (SEM). X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed that the AlN-SiC alloys had the wurtzite structure. Electron probe microanalysis (EPMA) and x-ray photoelectron spectroscopy (XPS) demonstrated that the resultant alloy crystals had non-stoichiometric ratios of Al:N and Si:C and a uniform composition throughout the alloy crystal from the interface to the surface. The composition ratio of Al:Si of the alloy crystals changed with the growth temperature, and differed from the original source composition, which was consistent with the results predicted by thermodynamic calculation of the solid-vapor distribution of each element. XPS detected the bonding between Si-C, Si-N, Si-O for the Si 2p spectra. The dislocation density decreased with the growth, which was lower than 106 cm−2 at the alloy surface, more than two orders of magnitude lower compared to regions close to the crystal/substrate interface, as determined by TEM.

scholarly journals Synthesis of Three-Dimensional Fe3O4/Graphene Aerogels for the Removal of Arsenic Ions from Water

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Yan Ye ◽  
Da Yin ◽  
Bin Wang ◽  
Qingwen Zhang
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
3D Structure ◽  
Three Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Aerogels ◽  
Transmission Electron ◽  
Potential Applications ◽  
Removal Of Arsenic

We report the synthesis of three-dimensional Fe3O4/graphene aerogels (GAs) and their application for the removal of arsenic (As) ions from water. The morphology and properties of Fe3O4/GAs have been characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and superconducting quantum inference device. The 3D nanostructure shows that iron oxide nanoparticles are decorated on graphene with an interconnected network structure. It is found that Fe3O4/GAs own a capacity of As(V) ions adsorption up to 40.048 mg/g due to their remarkable 3D structure and existence of magnetic Fe3O4nanoparticles for separation. The adsorption isotherm matches well with the Langmuir model and kinetic analysis suggests that the adsorption process is pseudo-second-ordered. In addition to the excellent adsorption capability, Fe3O4/GAs can be easily and effectively separated from water, indicating potential applications in water treatment.

scholarly journals Facile Preparation of Rod-like MnO Nanomixtures via Hydrothermal Approach and Highly Efficient Removal of Methylene Blue for Wastewater Treatment

Nanomaterials ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 10 ◽  
Author(s):  
Yuelong Xu ◽  
Bin Ren ◽  
Ran Wang ◽  
Lihui Zhang ◽  
Tifeng Jiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Degradation Mechanism ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Transmission Electron ◽  
Degradation Ratio ◽  
Hydrothermal Approach

In the present study, nanoscale rod-shaped manganese oxide (MnO) mixtures were successfully prepared from graphitic carbon nitride (C3N4) and potassium permanganate (KMnO4) through a hydrothermal method. The as-prepared MnO nanomixtures exhibited high activity in the adsorption and degradation of methylene blue (MB). The as-synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), surface area analysis, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Furthermore, the effects of the dose of MnO nanomixtures, pH of the solution, initial concentration of MB, and the temperature of MB removal in dye adsorption and degradation experiments was investigated. The degradation mechanism of MB upon treatment with MnO nanomixtures and H2O2 was studied and discussed. The results showed that a maximum adsorption capacity of 154 mg g−1 was obtained for a 60 mg L−1 MB solution at pH 9.0 and 25 °C, and the highest MB degradation ratio reached 99.8% under the following optimum conditions: 50 mL of MB solution (20 mg L−1) at room temperature and pH ≈ 8.0 with 7 mg of C, N-doped MnO and 0.5 mL of H2O2.

scholarly journals Photocatalytic activity of Cu2O/ZnO nanocomposite for the decomposition of methyl orange under visible light irradiation

2019 ◽  
Vol 26 (1) ◽  
pp. 104-113 ◽  
Author(s):  
Xian-sheng Wang ◽  
Yu-duo Zhang ◽  
Qiao-chu Wang ◽  
Bo Dong ◽  
Yan-jia Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Visible Region ◽  
Methyl Orange Solution ◽  
Degradation Efficiency ◽  
X Ray ◽  
Transmission Electron ◽  
Consistent Performance ◽  
Two Phases

AbstractZnO is modified by Cu2O by the process of precipitation and calcination. X-ray diffraction has shown that Cu2O/ZnO catalysts are made of highly purified cubic Cu2O and hexagonal ZnO. Scanning electron microscopy and transmission electron microscopy have shown that ZnO adhered to the surface of Cu2O. Due to the doping of Cu2O, the absorption range of the Cu2O/ZnO catalyst is shifted from the ultraviolet to the visible region due to diffuse reflection. X-ray photoelectron spectroscopy and photoluminescence spectra have confirmed that there is a substantial interaction between the two phases of the resultant catalyst. The degradation efficiency of Cu2O/ZnO on methyl orange solution is obviously enhanced compared to Cu2O and ZnO. The maximum degradation efficiency is 98%. The degradation efficiency is affected by the pH of the solution and initial concentration. After three rounds of recycling, the degradation rate is almost same. This shows a consistent performance of Cu2O/ZnO. The increase in catalytic ability is related to the lattice interaction caused by the doping of Cu2O.

Sign in / Sign up

Export Citation Format

Share Document