scholarly journals Novel Ag/Kaolin Nanocomposite as Adsorbent for Removal of Acid Cyanine 5R from Aqueous Solution

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Saeedeh Hashemian ◽  
Mohammad Reza Shahedi
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Process ◽  
Alkaline Condition ◽  
Order Kinetic ◽  
Nano Composite ◽  
Order Kinetic Model ◽  
Endothermic Process ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

Ag/kaolin nanocomposite was prepared by reduction of Ag+ion with ethanol at alkaline condition on kaolin surface. Nanocomposite was characterized by FTIR, XRD, TEM, and BET methods. Results showed the Ag/kaolin composite has particle size 50 nm. The surface area was increased from kaolin to Ag/kaolin from 1.0215 to 7.409 m2 g−1, respectively. Ag/kaolin nanocomposite was used for adsorption of acid cyanine 5R (AC5R) from aqueous solution. The effect of parameters such as contact time, pH, and mass of nano composite has been investigated. The maximum percentage of adsorption of AC5R was found at pH 3 and contact time of 60 min. The higher percentage removal of AC5R by Ag/kaolin than kaolin can be attributed to catalytic activity of Ag on the surface of kaolin. The experimental data was fitted by pseudo-second-order kinetic model. The adsorption isotherm data could be well interpreted by Langmuir isotherm model. From the results of thermodynamic study, the adsorption process of AC5R onto Ag/kaolin nanocomposite was spontaneous and endothermic process. The process is clean and safe for purifying of water pollution.

Use of Natural Kaolinite Clay as an Adsorbent to Remove PB(II), CD(II), and CU(II) from Aqueous Solution

2014 ◽  
Vol 805 ◽  
pp. 581-584 ◽  
Author(s):  
Débora Martins Aragão ◽  
Maria de Lara P.M. Arguelho ◽  
Carolina Mangieri Oliveira Prado ◽  
José do Patrocinio Hora Alves
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Process ◽  
Adsorption Equilibrium ◽  
Northeast Brazil ◽  
Order Kinetic ◽  
Kaolinite Clay ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Natural kaolinite clay collected in the State of Sergipe (northeast Brazil) was used as an adsorbent for the ions Pb2+, Cd2+, and Cu2+present in aqueous solution. Adsorption equilibrium was reached rapidly, enabling use of a contact time of 30 minutes, and maximum adsorption was achieved at pH 7.0. For all three metal ions, the adsorption data could be fitted using the Langmuir isotherm and the adsorption process obeyed a pseudo-second order kinetic model.

Adsorption of enrofloxacin from aqueous solution by bentonite

Clay Minerals ◽  
2013 ◽  
Vol 48 (4) ◽  
pp. 627-637 ◽  
Author(s):  
J. X. Zhang ◽  
Q. X. Zhou ◽  
W. Li
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Equilibrium ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Freundlich Model ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Better Than

AbstractThe removal of enrofloxacin, a fluoroquinolone antibiotic, from aqueous solution by adsorption onto bentonite was investigated in this study. The effects of initial concentrations, contact time and temperature on the adsorption of enrofloxacin were studied via batch experiments. The adsorption equilibrium was achieved within 60 min for all studied concentrations. The adsorption capacity increased with the increase of initial concentration within a concentration range. Higher temperatures were favourable for the adsorption. The change of Gibbs free energy (ΔG°), change of enthalpy (ΔH°) and change of entropy (ΔS°) were evaluated and the results indicate that the adsorption should be an endothermic and spontaneous process. The Langmuir isotherm model fitted to the experimental data better than the Freundlich model. The adsorption follows the pseudo-second order kinetic model.

scholarly journals Mn(II) Ions Biosorption from Aqueous Solution Using Pleurotus Spent Mushroom Compost under Batch Experiment

2015 ◽  
Vol 773-774 ◽  
pp. 1101-1105 ◽  
Author(s):  
Ain Nihla Kamarudzaman ◽  
Tay Chia Chay ◽  
Amnorzahira Amir ◽  
Suhaimi Abdul Talib
Keyword(s):  
Experimental Data ◽  
Aqueous Solution ◽  
Contact Time ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Mushroom Compost ◽  
Spent Mushroom Compost ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The Pleurotus spent mushroom compost was selected as biosorbent to sorption Mn(II) ions. The Mn(II) ions biosorption was investigated under batch experiments. The influences of pH, contact time and initial Mn(II) concentration were also investigated. The optimum Mn(II) ions biosorption was achieved at pH 6, 20 minutes of contact time and 10 mg/L of initial Mn(II) concentration using 1.0 g biosorbent dosage. The Mn(II) ions biosorption experimental data were best described by the Langmuir isotherm model and pseudo-second order kinetic model. As conclusion, the Pleurotus spent mushroom compost can be used to sorption the Mn(II) ions from the aqueous solution.

Fast Removal of Pb2+ from Aqueous Solution by Water Insoluble Konjac Glucomannan

2009 ◽  
Vol 610-613 ◽  
pp. 65-68 ◽  
Author(s):  
Xue Gang Luo ◽  
Feng Liu ◽  
Xiao Yan Lin
Keyword(s):  
Aqueous Solution ◽  
Correlation Coefficients ◽  
Konjac Glucomannan ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Equilibrium Process ◽  
Fast Removal

Konjac glucomannan (KGM) was converted into water insoluble konjac glucomannan (WIKGM) by treating with NaOH through completely deacetylated reaction. Adsorption study was carried out for the adsorption of Pb2+ from aqueous solution using water insoluble konjac glucomannan. The influences of pH, contact time, temperature and initial Pb2+ concentration on the absorbent were studied. Results of kinetic data showed that the Pb2+ adsorption rate was fast and good correlation coefficients were obtained for the pseudo second-order kinetic model. The equilibrium process was described well by the Langmuir isotherm model with maximum adsorption capacity of 9.18 mg/g on WIKGM at 25°C.

scholarly journals Adsorption of tricresyl phosphate onto graphene nanomaterials from aqueous solution

2017 ◽  
Vol 76 (6) ◽  
pp. 1565-1573 ◽  
Author(s):  
Jun Liu ◽  
Siying Xia ◽  
Xiaomeng Lü ◽  
Hongxiang Shen
Keyword(s):  
Experimental Data ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Tricresyl Phosphate ◽  
Batch Mode ◽  
Order Kinetic Model ◽  
Endothermic Process ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Increasing Temperature

Phosphorus flame retardant tricresyl phosphate (TCP) adsorption on graphene nanomaterials from aqueous solutions was explored using batch and column modes. Comparative studies were performed regarding the kinetics and equilibrium of TCP adsorption on graphene oxide (GO) and graphene (G) in batch mode. The adsorption kinetics exhibited a rapid TCP uptake, and experimental data were well described by the pseudo-second-order kinetic model. Adsorption isotherm data of TCP on the two adsorbents displayed an improved TCP removal performance with increasing temperature at pH 5, while experimental data were well described by the Langmuir isotherm model with a maximum adsorption capacity of 87.7 mg·g−1 for G, and 30.7 mg·g−1 for GO) at 303 K. The thermodynamic parameters show that the adsorption reaction is a spontaneous and endothermic process. In addition, dynamic adsorption of TCP in a fixed G column confirmed a faster approach to breakthrough at high flow rate, high influent TCP concentration, and low filling height of adsorbent. Breakthrough data were successfully described by the Thomas and Yoon-Nelson models.

Adsorption of Cu(II), Ni(II) and Zn(II) ions by nano kaolinite: Thermodynamics and kinetics studies

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Adsorption Process ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

An easy route for preparation emulsion of kaolinite (Al2Si2O5.4H2O) from Sweileh sand deposits, west Amman, Jordan by hydrochloric acid under continuous stirring for 4 h at room temperature was performed and nano kaolinite powder was used as an adsorbent for the removal of Cu(II), Zn(II) and Ni(II) ions. Nano kaolinite was characterized by XRD, FT-IR and SEM techniques. Effect of pH, adsorbent dose, initial metal ion concentration, contact time and temperature on adsorption process was examined. The negative values of ΔGo and the positive value of ΔHo revealed that the adsorption process was spontaneous and endothermic. The Langmuir isotherm model fitted well to metal ions adsorption data and the adsorption capacity. The kinetic data provided the best correlation of the adsorption with pseudo-second order kinetic model. In view of promising efficiency, the nano kaolinite can be employed for heavy metal ions adsorption.

Application of MnO2 Materials to Dye Removal from Aqueous Solution by Adsorption

2013 ◽  
Vol 361-363 ◽  
pp. 760-763 ◽  
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Hao Li
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Dye Removal ◽  
Good Alternative ◽  
Order Kinetic ◽  
Dye Wastewater ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The adsorption capacity was compared for the dye wastewater onto adsorbent MnO2. The effects of contact time and dosage of adsorbent were studied. The adsorption kinetics was analyzed. The results showed that MnO2 possessed higher adsorption capacity to Methylene blue than Methyl orange which the removal efficiency could reached 94.82%and 78.63% respectively under the conditions (the dosage1.2g/L, time 60min, initial dye concentration 50mg/L, pH7). The dynamical data fit well with the pseudo second order kinetic model. The MnO2 has higher Methylene blue adsorption capacity in short equilibrium times and are good alternative in wastewater treatment.

scholarly journals Synthesis of Large Pore LTL and MOR Zeolites and Use as Adsorbent for The Removal of Heavy Metal and Radioactive Metal Ions in Aqueous Solution

2021 ◽  
Author(s):  
Duy Hoai-Phuong Nguyen ◽  
Quang Thanh Le ◽  
Tung Cao Thanh Pham ◽  
Thanh Tu Le
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Order Kinetic ◽  
Experiment Data ◽  
Large Pore ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

Abstract Heavy metal and radioactive ions can cause serious environmental problems if they are not completely removed from wastewater as well as in groundwater. In this study, large pore LTL and MOR zeolites were successfully synthesized and used as adsorbent to remove Pb2+, Cu2+, Zn2+, Cd2+, Cs+ and Sr2+ ions in aqueous solution. At low initial concentration (10 ppm), LTL and MOR zeolites effectively removed above metal ions with removal efficiency in the range of 95–99%. Both zeolites showed high affinity to Cs+ and Pb2+ ions with the adsorption capacity of LTL zeolite to Cs+ and Pb2+ were 278.8 mg/g and 141.4 mg/g, and that of MOR zeolite were 238.8 mg/g and 178.9 mg/g, respectively. The EDS results showed that Pb2+ ions from the aqueous solution were exchanged with exchangeable Na+ ions in MOR zeolite and K+ ions in LTL zeolite. The pseudo-second-order kinetic model and Langmuir isotherm model fitted better to experiment data on the adsorption of metal ions on both LTL and MOR zeolite. This result revealed that the adsorption of these metal ions on LTL and MOR zeolite was monolayer chemisorption. The equilibrium adsorption results showed that the microstructure of zeolite significantly affected the adsorption capacity of LTL and MOR zeolite on removal of tested metal ions.

scholarly journals Adsorption of Co(II) from aqueous solution using municipal sludge biochar modified by HNO3

2021 ◽  
Author(s):  
Chunlian Hu ◽  
Wei Zhang ◽  
Yuantao Chen ◽  
Na Ye ◽  
DaWa YangJi ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Order Kinetic ◽  
Adsorption Effect ◽  
Surface Areas ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Adsorption Of Co

Abstract Herein adsorption studies were proposed on a carboxylated sludge biochar (CSB) material modified by HNO3 to assess its capacity in the removal of cobalt from aqueous solution. The as-prepared sludge biochar material were characterized by Brunaure-Emmett-Teller (BET), Fourier transform infrared (FT-IR), Thermogravimetric analysis (TGA), Energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The isotherm process could be well described by Langmuir isotherm model. The adsorption kinetics indicated that cobalt adsorption followed pseudo-second-order kinetic model. The mechanism between Co(II) and biochar involved electrostatic interaction, ion exchange, surface complexation and physical function. The adsorption capacity on CSB was as high as 72.27 mg·g−1, surpassing original sludge biochar (SB). This is due to the fact that CSB had abundant oxygen-containing functional groups and many hydroxyls, as well as, the BET surface areas increased when SB was modified by HNO3, which stimulate adsorption effect. Therefore, this work shows that CSB could be used as an efficient adsorbent to remove Co(II) in the wastewater.

scholarly journals Adsorption of Lead(II) Ions from Aqueous Solution onto Lignin

2009 ◽  
Vol 27 (4) ◽  
pp. 435-445 ◽  
Author(s):  
Laura Bulgariu ◽  
Dumitru Bulgariu ◽  
Theodor Malutan ◽  
Matei Macoveanu
Keyword(s):  
Aqueous Solution ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Batch System ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The adsorption of lead(II) ions from aqueous solution onto lignin was investigated in this study. Thus, the influence of the initial solution pH, the lignin dosage, the initial Pb(II) ion concentration and the contact time were investigated at room temperature (19 ± 0.5 °C) in a batch system. Adsorption equilibrium was approached within 30 min. The adsorption kinetic data could be well described by the pseudo-second-order kinetic model, while the equilibrium data were well fitted using the Langmuir isotherm model. A maximum adsorption capacity of 32.36 mg/g was observed. The results of this study indicate that lignin has the potential to become an effective and economical adsorbent for the removal of Pb(II) ions from industrial wastewaters.

Sign in / Sign up

Export Citation Format

Share Document