scholarly journals Adsorption Kinetics for the Removal of Hazardous Dye Congo Red by Biowaste Materials as Adsorbents

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Sumanjit Kaur ◽  
Seema Rani ◽  
Rakesh Kumar Mahajan
Keyword(s):  
Congo Red ◽  
Low Cost ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Experimental Conditions ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The present work aims to investigate the removal of dye congo red from aqueous solutions by two low-cost biowaste adsorbents such as ground nut shells charcoal (GNC) and eichhornia charcoal (EC) under various experimental conditions. The effect of contact time, ionic strength, temperature, pH, dye concentration, and adsorbent dose on the removal of dye was studied. The kinetic experimental data were fitted to pseudo-first order, pseudo-second order, intraparticle diffusion, Elovich model, and Bangham’s model. Results imply that adsorption of congo red on these adsorbents nicely followed the second order kinetic model and maximum adsorption capacity was found to be 117.6 and 56.8 mg g−1for GNC and EC at 318 K, however it increases with increase in temperature for both adsorbents. Equilibrium isotherms were analyzed by Langmuir, Freundlich, Temkin, Dubinin and Radushkevich, and Generalized Isotherms. Freundlich isotherm described the isotherm data with high-correlation coefficients. The results of the present study substantiate that biowaste material GNC and EC are promising adsorbents for the removal of the dye congo red.

Kinetics of lead ion biosorption from aqueous solution onto lyophilized Aspergillus niveus

2010 ◽  
Vol 5 (1) ◽  
Author(s):  
Hülya Karaca ◽  
Turgay Tay ◽  
Merih Kıvanç
Keyword(s):  
Adsorption Capacity ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Lead Ions ◽  
Lead Ion ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Aspergillus Niveus ◽  
Pseudo Second Order

The biosorption of lead ions (Pb2+) onto lyophilized fungus Aspergillus niveus was investigated in aqueous solutions in a batch system with respect to pH, contact time and initial concentration of the ions at 30 °C. The maximum adsorption capacity of lyophilized A. niveus was found to be 92.6 mg g−1 at pH 5.1 and the biosorption equilibrium was established about in 30 min. The adsorption capacity obtained is one of the highest value among those reported in the literature. The kinetic data were analyzed using the pseudo-first-order kinetic, pseudo-second-order kinetic, and intraparticle diffusion equations. Kinetic parameters, such as rate constants, equilibrium adsorption capacities, and related correlation coefficients for the kinetic models were calculated and discussed. It was found that the adsorption of lead ions onto lyophilized A. niveus biomass fit the pseudo-second-order kinetic model well. The Langmuir and Freundlich isotherm parameters for the lead ion adsorption were applied and the Langmuir model agreed better with the adsorption of lead ions onto lyophilized A. niveus.

Removal of Rhodamine B from Wastewater by Rectorite and Sepiolite-Kinetic Study and Equilibrium Isotherm Analyses

2011 ◽  
Vol 183-185 ◽  
pp. 362-366 ◽  
Author(s):  
Jun Li ◽  
Ming Zhen Hu
Keyword(s):  
Rhodamine B ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Order Kinetic ◽  
Isotherm Equation ◽  
Adsorption Removal ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Adsorption removal of a cationic dye, rhodamine B (RhB) from water onto rectorite and sepiolite was investigated. The rectorite and sepiolite were characterized by Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). Attempts were made to fit the isothermal data using Langmuir and Freundlich equations. The experimental results have demonstrated that the equilibrium data are fitted well by a Freundlich isotherm equation. Pseudo-first-order and pseudo-second-order models were considered to evaluate the rate parameters. The experimental data were well described by the pseudo-second-order kinetic model. The results indicate that the rectorite exhibited higher adsorption capacity for the removal of RhB than sepiolite and could be employed as a low-cost alternative in wastewater treatment for the removal of cationic dyes.

scholarly journals Aqueous Phase Adsorption of Pb (II) Ions onto Hymenoptera sphecidae (Mud-wasp) Nest

2020 ◽  
pp. 21-31
Author(s):  
Donald T. Kukwa ◽  
Peter A. Adie ◽  
Rose E. Kukwa ◽  
Paula D. Kungur
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Batch Process ◽  
Second Order ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Adsorbent Dose

Removal of Pb (II) ion from aqueous solution using Hymenoptera sphecidae (mud-wasp) nest was investigated using a batch process. The effect of pH, contact time and adsorbent dose were also investigated. The result showed that the adsorption of Pb (II) ion onto mud-wasp nest was dependent on pH, contact time and adsorbent dose. Adsorption patterns were analysed in terms of three bi-parameter isotherms of Langmuir, Freundlich and Temkin. Freundlich isotherm gave the best fit to the adsorption data with a correlation coefficient of 0.992, while monolayer sorption capacity yielded 41.667 mg/g. Lagergren’s pseudo first-order and pseudo second-order kinetic models were used to test the adsorption kinetics. The kinetic data were well described by the pseudo second-order kinetic model, suggesting that the process was chemisorption type.  The results showed that mud-wasp nest can be used as a low-cost adsorbent for the removal of Pb (II) ion from aqueous solutions.

Adsorption of Congo Red Dye from Aqueous Solutions by Montmorillonite as a Low-cost Adsorbent

2017 ◽  
Vol 16 (1) ◽  
Author(s):  
Yusef Omidi Khaniabadi ◽  
Hassan Basiri ◽  
Heshmatollah Nourmoradi ◽  
Mohammad Javad Mohammadi ◽  
Ahmad Reza Yari ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Congo Red ◽  
Low Cost ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Effective Option ◽  
Pseudo Second Order

AbstractIn this study, the sorption of Congo red (CR), as a toxic dye, from aqueous media was investigated using montmorillonite (MMT) as a low-cost adsorbent. The influence of several factors such as contact time, pH, adsorbent dosage, dye content, and ionic strength was investigated on the dye removal. MMT was characterized by Fourier transformed infrared (FTIR) spectroscopy and X-ray diffractometer (XRD). Different kinetic and isotherm models including pseudo-first and pseudo-second order kinetic and Langmuir and Freundlich were applied to analyze experimental data, respectively. The results showed that the data were well fitted by pseudo-second-order kinetic and Freundlich isotherm models. The optimum conditions for the sorption of CR were achieved over 40 min and at pH=2. According to the results of the present study, MMT can be used as a low-cost, eco-friendly and effective option for the adsorption of CR from aqueous solutions.

Fast Removal of Pb2+ from Aqueous Solution by Water Insoluble Konjac Glucomannan

2009 ◽  
Vol 610-613 ◽  
pp. 65-68 ◽  
Author(s):  
Xue Gang Luo ◽  
Feng Liu ◽  
Xiao Yan Lin
Keyword(s):  
Aqueous Solution ◽  
Correlation Coefficients ◽  
Konjac Glucomannan ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Equilibrium Process ◽  
Fast Removal

Konjac glucomannan (KGM) was converted into water insoluble konjac glucomannan (WIKGM) by treating with NaOH through completely deacetylated reaction. Adsorption study was carried out for the adsorption of Pb2+ from aqueous solution using water insoluble konjac glucomannan. The influences of pH, contact time, temperature and initial Pb2+ concentration on the absorbent were studied. Results of kinetic data showed that the Pb2+ adsorption rate was fast and good correlation coefficients were obtained for the pseudo second-order kinetic model. The equilibrium process was described well by the Langmuir isotherm model with maximum adsorption capacity of 9.18 mg/g on WIKGM at 25°C.

scholarly journals Itaconic acid-modified layered double hydroxide as a ‎novel adsorbent for effective removal of Congo red from aqueous solutions

2021 ◽  
Author(s):  
Mohammad Dinari ◽  
Shirin Shabani
Keyword(s):  
Layered Double Hydroxide ◽  
Itaconic Acid ◽  
Congo Red ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Order Kinetic ◽  
Solution Ph ◽  
Pseudo Second Order ◽  
Double Hydroxide

Abstract Herein, we report the synthesis of Cu-Ca-Al/NO3-based layered double hydroxide through co-precipitation methodology. The prepared layered double hydroxide was then modified with itaconic acid. The physicochemical properties of the prepared materials were studied using Fourier transform-infrared spectroscopy, scanning electron microscopy, X-ray diffraction analysis, thermogravimetric analysis, and nitrogen adsorption/desorption technique. The prepared materials were then applied as novel adsorbents for the removal of Congo red as a model of an anionic dye from aqueous media. To reach maximum adsorption, the effect of parameters including sample solution pH, adsorbent amount, contact time, and initial concentration of Congo red on the adsorption process was investigated. Kinetic studies were also conducted to study the mechanism of adsorption. In this regard, the kinetic models of pseudo-first-order, pseudo-second-order, Elovich, and intra-particle diffusion were studied. The results showed that the adsorption of Congo red onto Cu-Ca-Al-LDH and LDH-ITA adsorbents followed the pseudo-second-order kinetic model. To evaluate the equilibrium adsorption data, different isotherms including Langmuir, Freundlich, and Dubinin-Radushkevich were also applied. The data revealed that the Freundlich isotherm provided the best fit with the equilibrium data of both adsorbents. Maximum adsorption capacities of 81 and 84 mg g− 1 were obtained using Cu-Ca-Al-LDH and LDH-ITA adsorbents, respectively.

scholarly journals Adsorption Behaviour of Chromium(VI) onto Surface Modified Sugarcane Waste

2013 ◽  
Vol 28 (1-2) ◽  
pp. 113-122
Author(s):  
Kedar Nath Ghimire ◽  
Deepak Wagle ◽  
Suman Lal Shrestha
Keyword(s):  
Volume Ratio ◽  
Freundlich Isotherm ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Method ◽  
Chromium Vi ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Surface Modified

An effective chemically modified adsorbent based on sugarcane waste has been prepared by treating with concentrated sulphuric acid in 2:1weight/volume ratio. Thus prepared adsorbent has been found to be effective in the adsorption of chromium from aqueous medium. The efficacy of the adsorbent in the removal of chromium was evaluated by batch adsorption method. The effect of initial concentration, contact time and pH of the solution was investigated. The maximum adsorption capacity onto this adsorbent was found to be 195 mg/g at their optimal pH 1 at which unmodified bagasse has only 58 mg/g. The characterization of adsorbent was done by determining surface area and Boehm’s titration method. Freundlich isotherm and pseudo-second order kinetic model gave better explanation of the adsorption process.

Investigation of Modified Mangrove Bark on the Sorption of Oil in Water

2014 ◽  
Vol 567 ◽  
pp. 74-79 ◽  
Author(s):  
Asadpour Robabeh ◽  
Nasiman Sapari ◽  
Mohamed Hasnain Isa ◽  
Kalu Uka Orji
Keyword(s):  
Palmitic Acid ◽  
Adsorption Capacity ◽  
Sorption Capacity ◽  
Oil Spills ◽  
Low Cost ◽  
Correlation Coefficients ◽  
Kinetic Studies ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Order Kinetic Model

Today oil spills generally cause worldwide worry due to their damaging effects on environment. Use of agricultural wastes such as raw and modified mangrove barks (RhizophoraApiculata), as an abundant and low cost adsorbent for oil-products spill cleanup in aquatic systems, has been developed to control these spills. Sorption capacity can improve by modification of adsorbent. The modification significantly increased the hydrophobicity of the adsorbent. The raw mangrove bark was modified using fatty acid (Palmitic acid) to improve its adsorption capacity. Oil sorption capacity of the modified bark was studied and compared with the raw bark. Kinetic tests were conducted with a series of contact time. The kinetic studies show good correlation coefficients for a pseudo-first-order kinetic model. A correlation between surface functional groups of the adsorbent was studied by FTIR spectrum. The results gave the maximum adsorption capacity of 2640.00 ± 2.00 mg/g for Palmitic acid treated bark (PTB). The prepared adsorbent revealed the potential to use as a low-cost adsorbent in oil-spill clean-up.

The Removal of Heavy Metals from Aqueous Solution by Utilizing Modified β-Cyclodextrin Microspheres

2010 ◽  
Vol 113-116 ◽  
pp. 632-638
Author(s):  
Feng Yu Li ◽  
Xiao Mei Sun ◽  
Bu Hai Li
Keyword(s):  
Heavy Metals ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Heavy Metal Concentration ◽  
Second Order ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Removal Of Heavy Metals ◽  
Pseudo Second Order

Batch adsorption experiments were carried out to remove heavy metals Cu(II)and Ni(II) by pyromellitic dianhydride (PMDA) grafted β-Cyclodextrin (β-CD). The effects concerning the pH of the solution, contact time and initial heavy metal concentration were studied and discussed. The adsorption values increased significantly after a large number of carboxyl groups were gragfted on the microspheres surface. In order to investigate the mechanism of sorption, adsorption data were modeled using the pseudo-first-order and pseudo-second-order kinetic equation. It was found that kinetic studies showed good correlation coefficients for a pseudo-second-order kinetic model, confirming that the sorption rate was controlled by chemical adsorption. The equilibrium process was better described by the Langmuir isotherm than the Freundlich isotherm. XPS analysis further confirmed that the carboxyl group which grafted on the surface of the β-CD microspheres play a very important role in the removal of heavy metals.

scholarly journals Syringa vulgaris leaves powder a novel low-cost adsorbent for methylene blue removal: isotherms, kinetics, thermodynamic and optimization by Taguchi method

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Giannin Mosoarca ◽  
Cosmin Vancea ◽  
Simona Popa ◽  
Marius Gheju ◽  
Sorina Boran
Keyword(s):  
Methylene Blue ◽  
Low Cost ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorbent Surface ◽  
Order Kinetic Model ◽  
Endothermic Process ◽  
Pseudo Second Order ◽  
Better Than

Abstract In this study, the potential of a new low-cost adsorbent, Syringa vulgaris leaves powder, for methylene blue adsorption from aqueous solution was investigated. The adsorbent surface was examined using SEM and FTIR techniques. The experiments were conducted, in batch system, to find out the effect of pH, contact time, adsorbent dose, initial dye concentration, temperature and ionic strength on dye adsorption. The process is best described by Langmuir isotherm and the pseudo second order kinetic model. Maximum adsorption capacity, 188.2 (mg g−1), is better than other similar adsorbent materials. Thermodynamic parameters revealed a spontaneous and endothermic process, suggesting a physisorption mechanism. A Taguchi orthogonal array (L27) experimental design was used to determine the optimum conditions for the removal of dye. Various desorbing agents were used to investigate the regeneration possibility of used adsorbent. Results suggest that the adsorbent material is very effective for removal of methylene blue from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document