scholarly journals Rheological Study on ATBS-AM Copolymer-Surfactant System in High-Temperature and High-Salinity Environment

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Muhammad Shahzad Kamal ◽  
Ibnelwaleed Ali Hussien ◽  
Abdullah Saad Sultan ◽  
Ming Han
Keyword(s):  
High Temperature ◽  
Rheological Properties ◽  
Saline Water ◽  
Divalent Cations ◽  
Polymer Concentration ◽  
Sodium Dodecyl ◽  
Experimental Studies ◽  
Viscosity Reduction ◽  
Tertiary Butyl ◽  
Water Viscosity

Experimental studies were conducted to evaluate the rheological properties of surfactant-polymer (SP) system. This SP system consists of a copolymer of acrylamide (AM) and acrylamido tertiary butyl sulfonate (ATBS) and sodium dodecyl sulphate (SDS) surfactant. Effects of surfactant concentration, temperature, polymer concentration, and salinity on rheological properties of SP system were investigated by means of oscillation and shear measurements. Comparison with classical partially hydrolyzed polyacrylamide (HPAM) was made. For the same temperature range, the viscosity drop for HPAM was about four times higher than the viscosity drop for ATBS-AM copolymer. In deionized water, viscosity of both polymers and SP systems was very high as compared to viscosity in saline water. Viscosity reduction of ATBS-AM copolymer was higher for salts having divalent cations. The SP system showed precipitation in presence of divalent cations. It worked well with monovalent cations even at relatively high salinities. The addition of 0.1% surfactant to the polymer resulted in a 60% decrease in the viscosity. Some interfacial rheological experiments were also carried out to investigate the behaviors on the interface between SP solutions and oil. Addition of 0.1% surfactant showed a 65% decrease inG′at SP solution-oil interface. SP system consisting of ATBS-AM and SDS showed better performance at high temperature compared to HPAM-SDS system. Due to precipitation, the SP system should be restricted to environment having low divalent cations.

Expanding Polymer Injectivity Tests on a Second Giant Carbonate UAE Oil Reservoir at High Salinity & High Temperature Conditions.

2021 ◽  
Author(s):  
S.A. Baloch ◽  
J.M. Leon ◽  
S.K. Masalmeh ◽  
D. Chappell ◽  
J. Brodie ◽  
...  
Keyword(s):  
High Temperature ◽  
Polymer Solution ◽  
High Salinity ◽  
Laboratory Data ◽  
Experimental Studies ◽  
Carbonate Reservoirs ◽  
Field Conditions ◽  
Sweep Efficiency ◽  
Tertiary Butyl ◽  
Solution Preparation

Abstract Over the last few years, ADNOC has systematically investigated a new polymer-based EOR scheme to improve sweep efficiency in high temperature and high salinity (HTHS) carbonate reservoirs in Abu Dhabi (Masalmeh et al., 2014). Consequently, ADNOC has developed a thorough de-risking program for the new EOR concept in these carbonate reservoirs. The de-risking program includes extensive laboratory experimental studies and field injectivity tests to ensure that the selected polymer can be propagated in the target reservoirs. A new polymer with high 2-acrylamido-tertiary-butyl sulfonic acid (ATBS) content was identified, based on extensive laboratory studies (Masalmeh, et al., 2019, Dupuis, et al., 2017, Jouenne 2020), and an initial polymer injectivity test (PIT) was conducted in 2019 at 250°F and salinity >200,000 ppm, with low H2S content (Rachapudi, et al., 2020, Leon and Masalmeh, 2021). The next step for ADNOC was to extend polymer application to harsher field conditions, including higher H2S content. Accordingly, a PIT was designed in preparation for a multi-well pilot This paper presents ADNOC's follow-up PIT, which expands the envelope of polymer flooding to dissolve H2S concentrations of 20 - 40 ppm to confirm injectivity at representative field conditions and in situ polymer performance. The PIT was executed over five months, from February 2021 to July 2021, followed by a chase water flood that will run until December 2021. A total of 108,392 barrels of polymer solution were successfully injected during the PIT. The extensive dataset acquired was used to assess injectivity and in-depth mobility reduction associated with the new polymer. Preliminary results from the PIT suggest that all key performance indicators have been achieved, with a predictable viscosity yield and good injectivity at target rates, consistent with the laboratory data. The use of a down-hole shut-in tool (DHSIT) to acquire pressure fall-off (PFO) data clarified the near-wellbore behaviour of the polymer and allowed optimisation of the PIT programme. This paper assesses the importance of water quality on polymer solution preparation and injection performance and reviews operational data acquired during the testing period. Polymer properties determined during the PIT will be used to optimise field and sector models and will facilitate the evaluation of polymer EOR in other giant, heterogeneous carbonate reservoirs, leading to improved recovery in ADNOC and Middle East reservoirs.

scholarly journals Two-Dimensional Tungsten Disulfide-Based Ethylene Glycol Nanofluids: Stability, Thermal Conductivity, and Rheological Properties

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1340
Author(s):  
Syed Nadeem Abbas Shah ◽  
Syed Shahabuddin ◽  
Mohd Faizul Mohd Sabri ◽  
Mohd Faiz Mohd Salleh ◽  
Suhana Mohd Said ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Electron Microscopy ◽  
Thermal Conductivity ◽  
Zeta Potential ◽  
Ethylene Glycol ◽  
Rheological Properties ◽  
Sodium Dodecyl ◽  
Viscosity Reduction ◽  
Measuring System ◽  
Potential Candidate

Developing stable nanofluids and improving their thermo-physical properties are highly important in heat transfer applications. In the present work, the stability, thermal conductivity, and rheological properties of tungsten disulphide (WS2) nanoparticles (NPs) with ethylene glycol (EG) were profoundly examined using a particle size analyzer, zeta-sizer, thermal property analyzer, rheometer, and pH measuring system. WS2 NPs were characterized by various techniques, such as XRD (X-Ray Diffraction), FTIR (Fourier Transform Infrared Spectroscopy), FESEM (Field emission scanning electron microscopy), and high-resolution transmission electron microscopy (HRTEM). The nanofluids were obtained with the two-step method by employing three volume concentrations (0.005%, 0.01%, and 0.02%) of WS2. The influence of different surfactants (Sodium dodecyl sulphate (SDS), Sodium dodecylbenzenesulfonate (SDBS), Cetyltrimethylammonium bromide (CTAB)) with various volume concentrations (0.05–2%) on the measured properties has also been evaluated. Pristine WS2/EG nanofluids exhibit low zeta potential values, i.e., −7.9 mV, −9.3 mV, and −5 mV, corresponding to 0.005%, 0.01%, and 0.02% nanofluid, respectively. However, the zeta potential surpassed the threshold (±30 mV) and the maximum values reached of −52 mV, −45 mV, and 42 mV for SDS, SDBS, and CTAB-containing nanofluids. This showed the successful adsorption of surfactants onto WS2, which was also observed through the increased agglomerate size of up to 1720 nm. Concurrently, particularly for 0.05% SDS with 0.005% WS2, thermal conductivity was enhanced by up to 4.5%, with a corresponding decrease in viscosity of up to 10.5% in a temperature range of (25–70 °C), as compared to EG. Conversely, the viscoelastic analysis has indicated considerable yield stress due to the presence of surfactants, while the pristine nanofluids exhibited enhanced fluidity over the entire tested deformation range. The shear flow behavior showed a transition from a non-Newtonian to a Newtonian fluid at a low shear rate of 10 s−1. Besides this, the temperature sweep analysis has shown a viscosity reduction in a range of temperatures (25–70 °C), with an indication of a critical temperature limit. However, owing to an anomalous reduction in the dynamic viscosity of up to 10.5% and an enhancement in the thermal conductivity of up to 6.9%, WS2/EG nanofluids could be considered as a potential candidate for heat transfer applications.

A UNIQUE FINDING OF ZIRCON INTO BADDELEYITE TRANSFORMATION (THE ICHETJU ORE OCCURRENCE, THE MIDDLE TIMAN)

2018 ◽  
pp. 27-35
Author(s):  
S. G. Skublov ◽  
A. O. Krasotkina ◽  
A. B. Makeyev ◽  
O. L. Galankina ◽  
A. E. Melnik
Keyword(s):  
High Temperature ◽  
Experimental Studies ◽  
Middle Timan ◽  
Natural Analogues ◽  
Opposite Situation ◽  
Formation Conditions

Findings of the growth relationships between baddeleyite and zircon are rare, due to significant differences in the formation conditions of the minerals. A reaction replacement (partial to complete) of baddeleyite by zircon is possible during metamorphism accompanied by the interaction with high-Si fluids. The opposite situation, when zircon is replaced by baddeleyite, is extremely rare in the nature. Transformation of zircon from polymineral (compound) ore occurrence Ichetju (the Middle Timan) with the formation of microaggregates of baddeleyite, ratile and florencite has been found out. The size of the largest segregations of baddeleyite does not exceed 10 microns in diameter. Microaggregates are unevenly related to the rim of zircon with a thickness of 10 to 50 rfn, voids and cracks across the grain. Altered zircon rim (a mixture of newly formed minerals) is characterized by sharply increased composition of REE (especially LREE), Y, Nb, Ca, Ti. The composition of Th and U also increases. An overview of the experimental studies on the reaction between zircon and baddeleyite and single natural analogues allows to make a conclusion that the most likely mechanism of the transformation of zircon from ore occurrence Ichetju to baddeleyite (intergrowth with ratile and florencite) is due to the effect of interaction of primary zircon with high-temperature (higher than 500—600°C) alkaline fluids transporting HFSE (REE, Y, Nb, Ti). This is indirectly confirmed by the findings of zircon with anomalous high composition of Y and REE up to 100000 and 70000 ppm respectively.

Studying dispersed and rheological properties of hydrocarbon-containing acid emulsions and their efficiency in removing asphalt-resin-paraffin deposits

2020 ◽  
pp. 128-139
Author(s):  
M. Yu. Shumakher ◽  
V. V. Konovalov ◽  
A. P. Melnikov
Keyword(s):  
Aqueous Solution ◽  
Hydrochloric Acid ◽  
Rheological Properties ◽  
Reaction Rate ◽  
Experimental Studies ◽  
Efficient Removal ◽  
Reservoir Properties ◽  
Hydrocarbon Solvents ◽  
Formation Zone ◽  
Effect Of The Composition

Currently, the treatment of the bottomhole formation zone with acidic compositions is one of the most common methods to intensify the oil inflow. The use of various modified acid compositions increases the efficiency of acid treatments on the bottomhole formation zone. Acid compositions, including those containing hydrocarbon solvents, which contribute to more efficient removal of organic colmatants, affect the reaction rate of the reagent with the rock and processing equipment, change the reservoir properties, etc.The article presents the results of experimental studies, which are aimed at establishing the effect of the composition of hydrocarbon-containing acidic emulsions consisting of an aqueous solution of hydrochloric acid, toluene and Neonol AF 9-10 on their dispersed and rheological properties, as well as their efficiency in removing paraffin deposits.

Arthrophytum scoparium Extract Improves Memory Impairment and Affects Acetylcholinesterase Activity In Mice Brain

2020 ◽  
Vol 21 (6) ◽  
pp. 480-487
Author(s):  
Med A. Smach ◽  
Jawhar Hafsa ◽  
Bassem Charfeddine ◽  
Hedi Dridi ◽  
Khalifa Limem ◽  
...  
Keyword(s):  
Antioxidant Activities ◽  
Saline Water ◽  
Experimental Studies ◽  
Chronic Administration ◽  
Acetylcholinesterase Activity ◽  
Control Group ◽  
Pharmacological Activities ◽  
Oxidative Damages ◽  
Y Maze ◽  
Mice Brain

Background: Arthrophytum scoparium (Pomel) Iljin (Amaranthaceae family) has been widely used in traditional Tunisian medicine to treat many disorders such as migraine, headache, and neurological disorders. This study investigates the effect of Arthrophytum scoparium Aqueous Extract (ASAE) on cognitive impairments and oxidative injury induced by galactose (10%) in a mouse model. Materials and Methods: The mice were divided randomly into 4 experimental groups, including the control group (saline water 9 ‰), Galactose group, Scop group (300 mg/kg/d), and Scop+Gal group (300 mg/kg/d). Mice received the corresponding solutions by intraperitoneal injection (i.p.) for 7 days before the Y-maze active tests. Galactose 10% was given to all groups except control and Scop groups, 30 min before the trial. Levels of Acetylcholinesterase Activity (AChE), Ascorbic Acid (AA), Gluthatione (GSH) and Malondialdehyde (MDA) in mice brains were examined. Results: Chronic administration of galactose significantly impaired cognitive performance in Y maze, caused marked oxidative damages and a significant increase in the acetylcholinesterase activity as compared to other groups. On the contrary, ASAE (300 mg/kg) treatment suppressed galactoseinduced oxidative damage by ameliorating the increased levels of GSH and AA. Moreover, ASAE treatment reduced brain AChE activities in the galactose-induced model. Conclusion: These findings suggest that ASAE exerts potent anti-amnesic effects via the modulation of cholinergic and antioxidant activities. The observed pharmacological activities should be further evaluated by detailed experimental studies and validated by clinical trials.

scholarly journals Evaluation of Micro-Mechanism and High- and Low-Temperature Rheological Properties of Disintegrated High Volume Crumb Rubber Asphalt (DHVRA)

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1145
Author(s):  
Wei Li ◽  
Sen Han ◽  
Xiaokang Fu ◽  
Ke Huang
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Rheological Properties ◽  
Particle Diameter ◽  
Gel Permeation Chromatography ◽  
High Volume ◽  
Crumb Rubber ◽  
Test Method ◽  
Polar Component ◽  
Temperature Performance

The aims of this paper are to prepare disintegrated high volume crumb rubber asphalt (DHVRA) with low viscosity, good workability and low-temperature performance by adding disintegrating agent (DA) in the preparation process, and to further analyze the disintegrating mechanism and evaluated high-temperature and low-temperature rheological properties. To obtain DHVRA with excellent comprehensive performance, the optimum DA dosage was determined. Based on long-term disintegrating tests and the Fluorescence Microscopy (FM) method, the correlations between key indexes and crumb rubber (CR) particle diameter was analyzed, and the evaluation indicator and disintegrating stage division standard were put forward. Furthermore, Fourier transform infrared spectroscopy (FT-IR) and Gel Permeation Chromatography (GPC) was used to reveal the reaction mechanism, and the contact angle test method was adopted to evaluate the surface free energy (SFE). In addition, the high-temperature and low-temperature rheological properties were measured, and the optimum CR content was proposed. Results indicated that the optimum DA dosage was 7.5‰, and the addition of DA promoted the melt decomposition of CR, reduced the viscosity and improved the storage stability. The 135 °C rotational viscosity (RV) of DHVRA from mixing for 3 h could be reduced to 1.475 Pa·s, and the softening point difference was even less than 2 °C. The linear correlation between 135 °C RV and the diameter of CR particle in rubber asphalt system was as high as 0.968, and the viscosity decay rate (VDR) was used as the standard to divide the disintegrating process into a fast disintegrating stage, stable disintegrating stage and slight disintegrating stage. Compared to common rubber asphalt (CRA), DHVRA has an absorption peak at 960 cm−1 caused by trans olefin = C-H, and higher molecular weight and polar component of surface energy. Compared with CRA, although the high-temperature performance of DHVRA decreases slightly, the low-temperature relaxation ability can be greatly improved.

scholarly journals The intimate relationship between structural relaxation and the energy landscape of monatomic liquid metals

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Franz Demmel ◽  
Louis Hennet ◽  
Noel Jakse
Keyword(s):  
High Temperature ◽  
Velocity Field ◽  
Liquid State ◽  
Liquid Metals ◽  
Energy Landscape ◽  
Experimental Studies ◽  
Transport Parameter ◽  
Arrhenius Behavior ◽  
Liquid Aluminium ◽  
Potential Energy Landscape

AbstractThe characteristic property of a liquid, discriminating it from a solid, is its fluidity, which can be expressed by a velocity field. The reaction of the velocity field on forces is enshrined in the transport parameter viscosity. In contrast, a solid reacts to forces elastically through a displacement field, the particles are trapped in their potential minimum. The flow in a liquid needs enough thermal energy to overcome the changing potential barriers, which is supported through a continuous rearrangement of surrounding particles. Cooling a liquid will decrease the fluidity of a particle and the mobility of the neighbouring particles, resulting in an increase of the viscosity until the system comes to an arrest. This process with a concomitant slowing down of collective particle rearrangements might already start deep inside the liquid state. The idea of the potential energy landscape provides an attractive picture for these dramatic changes. However, despite the appealing idea there is a scarcity of quantitative assessments, in particular, when it comes to experimental studies. Here we present results on a monatomic liquid metal through a combination of ab initio molecular dynamics, neutron spectroscopy and inelastic x-ray scattering. We investigated the collective dynamics of liquid aluminium to reveal the changes in dynamics when the high temperature liquid is cooled towards solidification. The results demonstrate the main signatures of the energy landscape picture, a reduction in the internal atomic structural energy, a transition to a stretched relaxation process and a deviation from the high-temperature Arrhenius behavior of the relaxation time. All changes occur in the same temperature range at about $$1.4 \cdot T_{melting}$$ 1.4 · T melting , which can be regarded as the temperature when the liquid aluminium enters the landscape influenced phase and enters a more viscous liquid state towards solidification. The similarity in dynamics with other monatomic liquid metals suggests a universal dynamic crossover above the melting point.

Sign in / Sign up

Export Citation Format

Share Document