scholarly journals An Investigation of Biodiesel Production from Wastes of Seafood Restaurants

2014 ◽  
Vol 2014 ◽  
pp. 1-17 ◽  
Author(s):  
Nour Sh. El-Gendy ◽  
A. Hamdy ◽  
Salem S. Abu Amr
Keyword(s):  
Low Cost ◽  
Interactive Effect ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Quadratic Model ◽  
Molar Ratio ◽  
Mixing Rate ◽  
Biodiesel Standards ◽  
Model Equations ◽  
Better Than

This work illustrates a comparative study on the applicability of the basic heterogeneous calcium oxide catalyst prepared from waste mollusks and crabs shells (MS and CS, resp.) in the transesterification of waste cooking oil collected from seafood restaurants with methanol for production of biodiesel. Response surface methodology RSM based on D-optimal deign of experiments was employed to study the significance and interactive effect of methanol to oil M : O molar ratio, catalyst concentration, reaction time, and mixing rate on biodiesel yield. Second-order quadratic model equations were obtained describing the interrelationships between dependent and independent variables to maximize the response variable (biodiesel yield) and the validity of the predicted models were confirmed. The activity of the produced green catalysts was better than that of chemical CaO and immobilized enzyme Novozym 435. Fuel properties of the produced biodiesel were measured and compared with those of Egyptian petro-diesel and international biodiesel standards. The biodiesel produced using MS-CaO recorded higher quality than that produced using CS-CaO. The overall biodiesel characteristics were acceptable, encouraging application of CaO prepared from waste MS and CS for production of biodiesel as an efficient, environmentally friendly, sustainable, and low cost heterogeneous catalyst.

scholarly journals Response Surface Methodology for Biodiesel Production Using Calcium Methoxide Catalyst Assisted with Tetrahydrofuran as Cosolvent

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Nichaonn Chumuang ◽  
Vittaya Punsuvon
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Catalyst Concentration ◽  
Acid Methyl Ester ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Quadratic Model ◽  
Molar Ratio ◽  
Standard Requirement

The present study was performed to optimize a heterogeneous calcium methoxide (Ca(OCH3)2) catalyzed transesterification process assisted with tetrahydrofuran (THF) as a cosolvent for biodiesel production from waste cooking oil. Response surface methodology (RSM) with a 5-level-4-factor central composite design was applied to investigate the effect of experimental factors on the percentage of fatty acid methyl ester (FAME) conversion. A quadratic model with an analysis of variance obtained from the RSM is suggested for the prediction of FAME conversion and reveals that 99.43% of the observed variation is explained by the model. The optimum conditions obtained from the RSM were 2.83 wt% of catalyst concentration, 11.6 : 1 methanol-to-oil molar ratio, 100.14 min of reaction time, and 8.65% v/v of THF in methanol concentration. Under these conditions, the properties of the produced biodiesel satisfied the standard requirement. THF as cosolvent successfully decreased the catalyst concentration, methanol-to-oil molar ratio, and reaction time when compared with biodiesel production without cosolvent. The results are encouraging for the application of Ca(OCH3)2 assisted with THF as a cosolvent for environmentally friendly and sustainable biodiesel production.

Optimization of Esterification and Transesterification Reactions for Biodiesel Production from Crude Coconut Oil Using RSM Techniques

2016 ◽  
Vol 723 ◽  
pp. 610-615 ◽  
Author(s):  
Natta Pimngern ◽  
Vittaya Punsuvon
Keyword(s):  
Fatty Acid ◽  
Reaction Time ◽  
Acid Methyl Ester ◽  
Coconut Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Quadratic Model ◽  
Molar Ratio ◽  
Optimum Conditions ◽  
Model Equations

Crude coconut oil with high free fatty acid (FFA) content was used as a raw material to produce biodiesel. In this work, the esterification followed by transesterification of crude coconut oil with methanol is studied. The response surface methodology (RSM) with 5-level-3-factor central composite design (CCD) was applied to study the effect of different factors on the FFA content of esterification and the percentage of fatty acid methyl ester (FAME) conversion of transesterification. The FAME conversion was detected by proton magnetic resonance (1H-NMR) spectrometer. As a result, the optimum conditions for esterification were 6:1 of methanol-to-oil molar ratio, 0.75wt% of sulfuric acid (H2SO4) concentration and 90 min of reaction time. The optimum conditions for transesterification were 8.23:1 of methanol-to-oil molar ratio, 0.75wt% of sodium hydroxide (NaOH) concentration and 80 min of reaction time. Quadratic model equations were obtained describing the relationships between dependents and independent variables to minimize the FFA content and maximize the FAME conversion. Fuel properties of the crude coconut oil biodiesel were also examined followed ASTM and EN standards. The results showed that all properties met well with both standards.

scholarly journals Improved biodiesel production from waste cooking oil with mixed methanol–ethanol using enhanced eggshell-derived CaO nano-catalyst

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yeshimebet Simeon Erchamo ◽  
Tadios Tesfaye Mamo ◽  
Getachew Adam Workneh ◽  
Yedilfana Setarge Mekonnen
Keyword(s):  
Particle Size ◽  
Low Cost ◽  
Average Particle Size ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Average Particle ◽  
Cooking Oil ◽  
Nano Catalyst

AbstractIn this report, the utilization of mixed methanol–ethanol system for the production of biodiesel from waste cooking oil (WCO) using enhanced eggshell-derived calcium oxide (CaO) nano-catalyst was investigated. CaO nano-catalyst was produced by calcination of eggshell powder at 900 °C and followed by hydration-dehydration treatment to improve its catalytic activity. The particle size, morphology, and elemental composition of a catalyst were characterized by using XRD, SEM, and EDX techniques, respectively. After hydration-dehydration the shape of a catalyst was changed from a rod-like to honeycomb-like porous microstructure. Likewise, average particle size was reduced from 21.30 to 13.53 nm, as a result, its surface area increases. The main factors affecting the biodiesel yield were investigated, accordingly, an optimal biodiesel yield of 94% was obtained at 1:12 oil to methanol molar ratio, 2.5 wt% catalyst loading, 60 °C, and 120-min reaction time. A biodiesel yield of 88% was obtained using 6:6 equimolar ratio of methanol to ethanol, the yield even increased to 91% by increasing the catalyst loading to 3.5 wt%. Moreover, by slightly increasing the share of methanol in the mixture, at 8:4 ratio, the maximum biodiesel yield could reach 92%. Therefore, we suggest the utilization of methanol–ethanol mixture as a reactant and eggshell-derived CaO as a catalyst for enhanced conversion of WCO into biodiesel. It is a very promising approach for the development of low-cost and environmentally friendly technology. Properties of the biodiesel were also found in good agreement with the American (ASTM D6571) fuel standards.

scholarly journals Low-Cost Alternative Biodiesel Production Apparatus Based on Household Food Blender for Continuous Biodiesel Production for Small Communities

2021 ◽  
Author(s):  
Wijittra Wongjaikham ◽  
Doonyapong Wongsawaeng ◽  
Vareeporn Ratnitsai ◽  
Manita Kamjam ◽  
Kanokwan Ngaosuwan ◽  
...  
Keyword(s):  
Flow Rate ◽  
Palm Oil ◽  
Catalyst Concentration ◽  
Low Cost ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Reaction Volume ◽  
Small Communities ◽  
Production Apparatus

Abstract Fatty acid methyl esters (FAMEs) are sustainable biofuel that can alleviate high oil cost and environmental impacts of petroleum-based fuel. A modified 1,200 W high efficiency fruit blender was employed for continuous transesterification of various refined vegetable oils and waste cooking oil (WCO) using sodium hydroxide as a homogeneous catalyst. The following factors have been investigated on their effects on FAME yield: baffles, reaction volume, total reactant flow rate, methanol-oil molar ratio, catalyst concentration and reaction temperature. Results indicated that the optimal conditions were: 2,000 mL reaction volume, 50 mL/min total flow rate, 1% and 1.25% catalyst concentration for refined palm oil and WCO, respectively, 6:1 methanol-to-oil molar ratio and 62 - 63oC, obtaining yield efficiency over 96.5% FAME yield of 21.14 ´ 10-4 g.J-1 (for palm oil) and 19.39 ´ 10-4 g.J-1 (for WCO). All the properties of produced FAMEs meet the EN 14214 and ASTM D6751 standards. The modified household fruit blender could be a practical and low-cost alternative biodiesel production apparatus for continuous biodiesel production for small communities in remote areas.

scholarly journals Optimization of Waste Cooking Oil’s FFA as Biodiesel Feedstock

Teknomekanik ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 14-21
Author(s):  
Sri Rizki Putri Primandari ◽  
Andril Arafat ◽  
Harumi Veny
Keyword(s):  
Irradiation Time ◽  
Control Variable ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Cooking Oil ◽  
Biodiesel Feedstock ◽  
Temperature Irradiation ◽  
Acid Esterification ◽  
Central Composite

Waste cooking oil has high Free Fatty Acid (FFA). It affected on decreasing a biodiesel production. FFA reduction is one of important processes in biodiesel production from waste cooking oil. Thus, this study aimed to examine the optimum condition in FFA reduction. The process is assisted by using ultrasonic irradiation on acid esterification. Variables of the process are acid concentration, molar ratio of methanol and oil, and irradiation time. Meanwhile temperature irradiation on 45oC is a control variable. Process optimization is conducted by Response Surface Methodology (RSM) with Central Composite Design (CCD). The optimum conditions of response were 7.22:1 (methanol to oil molar ratio), 0.92% wt H2SO4, 26.04 minutes (irradiation time), and 45oC (irradiation temperature). Ultrasonic system reduced FFA significantly compared to conventional method.

scholarly journals Evaluation of Shell-Derived Calcium Oxide Catalysts for the Production of Biodiesel Esters from Cooking Oils

2021 ◽  
pp. 20-27
Author(s):  
Ngee Sing Chong ◽  
Francis Uchenna Okejiri ◽  
Saidi Abdulramoni ◽  
Shruthi Perna ◽  
Beng Guat Ooi
Keyword(s):  
Calcium Oxide ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
X Ray ◽  
Cooking Oil ◽  
Biodiesel Synthesis ◽  
Cooking Oils ◽  
The Cost ◽  
Percentage Conversion

Due to the high cost of feedstock and catalyst in biodiesel production, the viability of the biodiesel industry has been dependent on government subsidies or tax incentives. In order to reduce the cost of production, food wastes including eggshells and oyster shells have been used to prepare calcium oxide (CaO) catalysts for the transesterification reaction of biodiesel synthesis. The shells were calcined at 1000 °C for 4 hours to obtain CaO powders which were investigated as catalysts for the transesterification of waste cooking oil. The catalysts were characterized by Fourier Transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), X-ray powder diffraction (XRD), and X-ray fluorescence (XRF) spectroscopy. Reaction parameters such as methanol-to-oil molar ratio, CaO catalyst concentration, and reaction time were evaluated and optimized for the percentage conversion of cooking oil to biodiesel esters. The oyster-based CaO showed better catalytic activity when compared to the eggshell-based CaO under the same set of reaction conditions.

Genetic Algorithm Approach to Optimize Biodiesel Production by Ultrasonic System

2014 ◽  
Vol 9 (1) ◽  
pp. 59-70 ◽  
Author(s):  
Ebrahim Fayyazi ◽  
Barat Ghobadian ◽  
Gholamhassan Najafi ◽  
Bahram Hosseinzadeh
Keyword(s):  
Genetic Algorithm ◽  
Catalyst Concentration ◽  
Ultrasonic Method ◽  
Research Work ◽  
Optimization Method ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Genetic Algorithm Approach ◽  
Mixing Method

Abstract Ultrasonic processing is an effective tool to attain required mixing while providing the necessary activation energy in the field of biofuels. In this regard, optimization of fast transesterification of waste cooking oil is very important. The goal of this research paper is therefore to determine the effect of important parameters such as methanol to oil molar ratio, catalyst concentration (potassium hydroxide), temperature, and horn position on oil conversion to methyl ester in ultrasonic mixing method. Result of experiments showed that the optimum conditions for the transesterification process have been obtained as molar ratio of alcohol to oil as 6:1, catalyst concentration of 1 wt.%, temperature as 45°C, and horn position at the interface of methanol to oil. The results show that the ultrasonic method decreases the reaction time as much as up to eight times compare to the conventional stirring. For practically evaluating the theoretical optimum point using genetic algorithm, the obtained values were verified experimentally. In order to perform this, the catalyst concentration, temperature, and the time of reaction were determined, and the values are 1%, 48°C, and 449s, respectively. For the obtained values, the biodiesel conversion was 93.2%, so that the experimental optimum value is closed to that of the theoretical values. As a result, experimental data confirmed the obtained values from optimization method in this research work.

Current scenario of catalysts for biodiesel production: a critical review

2018 ◽  
Vol 34 (2) ◽  
pp. 267-297 ◽  
Author(s):  
Farrukh Jamil ◽  
Lamya Al-Haj ◽  
Ala’a H. Al-Muhtaseb ◽  
Mohab A. Al-Hinai ◽  
Mahad Baawain ◽  
...  
Keyword(s):  
Heterogeneous Catalysts ◽  
Low Cost ◽  
Bifunctional Catalyst ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalysts ◽  
Animal Fats ◽  
Current Scenario ◽  
Short Chain Alcohol

AbstractDue to increasing concerns about global warming and dwindling oil supplies, the world’s attention is turning to green processes that use sustainable and environmentally friendly feedstock to produce renewable energy such as biofuels. Among them, biodiesel, which is made from nontoxic, biodegradable, renewable sources such as refined and used vegetable oils and animal fats, is a renewable substitute fuel for petroleum diesel fuel. Biodiesel is produced by transesterification in which oil or fat is reacted with short chain alcohol in the presence of a catalyst. The process of transesterification is affected by the mode of reaction, molar ratio of alcohol to oil, type of alcohol, nature and amount of catalysts, reaction time, and temperature. Various studies have been carried out using different oils as the raw material; different alcohols (methanol, ethanol, butanol); different catalysts; notably homogeneous catalysts such as sodium hydroxide, potassium hydroxide, sulfuric acid, and supercritical fluids; or, in some cases, enzymes such as lipases. This article focuses on the application of heterogeneous catalysts for biodiesel production because of their environmental and economic advantages. This review contains a detailed discussion on the advantages and feasibility of catalysts for biodiesel production, which are both environmentally and economically viable as compared to conventional homogeneous catalysts. The classification of catalysts into different categories based on a catalyst’s activity, feasibility, and lifetime is also briefly discussed. Furthermore, recommendations have been made for the most suitable catalyst (bifunctional catalyst) for low-cost oils to valuable biodiesel and the challenges faced by the biodiesel industry with some possible solutions.

Green Catalyzing Transesterification of Soybean Oil with Methanol for Biodiesel Based on the Reuse of Waste River-Snail Shell

2010 ◽  
Vol 148-149 ◽  
pp. 794-798 ◽  
Author(s):  
Xiao Hua Liu ◽  
Hai Xin Bai ◽  
Dong Jie Zhu ◽  
Geng Cao
Keyword(s):  
Soybean Oil ◽  
Low Cost ◽  
Production Costs ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Solid Base ◽  
X Ray Diffraction ◽  
Green Catalyst ◽  
Snail Shell ◽  
Diffraction Effects

In this paper, calcined river-snail shell was used as a novel solid base catalyst in the transesterification of soybean oil with methanol for biodiesel production. The calcined river-snail shell was characterized using field emission scanning electron microscope and X-ray diffraction. Effects of transesterification process variables were investigated. The results indicated that river-snail shell calcined at 800 °C catalyzed the transesterification of soybean oil for biodiesel with a yield over 98 % under the conditions including catalyst of 3.0% (w/w), a molar ratio of methanol/oil of 9:1, reaction time of 3 h, and reaction temperature of 65 °C. As a low-cost green catalyst, calcined river-snail shell could not only minimize the environmental wastes resulted from the solid shell, but also reduce the production costs of biodiesel.

scholarly journals Waste cooking oil processing for fatty acid methyl ester and mono glycerides production with magnetite catalyst

Food Research ◽  
2020 ◽  
Vol 4 (S1) ◽  
pp. 220-226
Author(s):  
Widayat ◽  
Hadiyanto ◽  
D.A. Putra ◽  
Nursafitri I. ◽  
H. Satriadi ◽  
...  
Keyword(s):  
Acid Methyl Ester ◽  
Chemical Precipitation ◽  
Waste Cooking Oil ◽  
Acid Number ◽  
Biodiesel Production ◽  
National Standard ◽  
Molar Ratio ◽  
Oil Processing ◽  
Cooking Oil ◽  
Acid Methyl

The objective of this research was to produce biodiesel using waste cooking oil and various magnetite catalysts with the esterification-transesterification process. Magnetite catalysts tested were α- Fe2O3, α- Fe2O3/Al2O3, α- Fe2O3/ZSM-5 catalysts. Catalysts were prepared through chemical precipitation and calcination. The esterificationtransesterification process was carried out with the conditions WCO: methanol molar ratio of 15:1, catalyst (1% wt of oil), heated at 65℃ for 3 hrs. The results showed biodiesel production using α- Fe2O3-ZSM-5 catalyst obtained higher %FAME (83.28%), yield (91.915%) and monoglyceride content (16.72%) compared to others due to larger pore volume. Biodiesel produced passed the requirement of Indonesian National Standard (SNI) based on density, acid number and viscosity.

Sign in / Sign up

Export Citation Format

Share Document