scholarly journals Studies on Mechanical, Thermal, and Morphological Properties of Glass Fibre Reinforced Polyoxymethylene Nanocomposite

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
K. Mohan Babu ◽  
M. Mettilda
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Glass Fibre ◽  
Morphological Properties ◽  
Flexural Properties ◽  
Moulding Process ◽  
Sem Image ◽  
Injection Moulding Process ◽  
Twin Screw ◽  
Water Absorption Property

Polyoxymethylene is a material which has excellent mechanical properties similar to Nylon-6 filled with 30% GF. 75% POM and 25% glass fibre (POMGF) were blended with nanoclay to increase the tensile and flexural properties. Samples were extruded in twin screw extruder to blend POMGF and (1%, 3%, and 5%) Cloisite 25A nanoclay and specimens were prepared by injection moulding process. The tensile properties, flexural properties, impact strength, and hardness were investigated for the nanocomposites. The fibre pull-outs, fibre matrix adhesion, and cracks in composites were investigated by using scanning electron microscopy. 1% POMGF nanocomposite has low water absorption property. Addition of nanoclay improves the mechanical properties and thermal properties marginally. Improper blending of glass fibre and nanoclay gives low tensile strength and impact strength. SEM image shows the mixing of glass fibre and nanoclay among which 1% POMGF nanocomposite shows better properties compared to others. The thermal stability decreased marginally only with the addition of nanoclay.

Effect of Reinforcement and Processing Methods in PP/MWCNTs Nanocomposites

2013 ◽  
Vol 747 ◽  
pp. 575-578 ◽  
Author(s):  
S. Arun ◽  
S. Kanagaraj
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Processing Technique ◽  
Vital Role ◽  
Melt Mixing ◽  
Processing Methods ◽  
Moulding Process ◽  
Injection Moulding Process ◽  
Twin Screw ◽  
Multi Walled Carbon Nanotubes

The usage of polymers is increased in order to replace the conventional metals because of their low cost and weight. As the processing technique of polymers plays a vital role in their properties, Polypropylene (PP) and multi walled carbon nanotubes (MWCNTs) were chosen as a matrix and reinforcement, respectively in order to confirm the effective processing method to prepare nanocomposites. The PP/MWCNTs nanocomposites with different concentration of reinforcement such as 0, 0.5, 1.0, 1.5 and 2.0 wt. % were prepared by melt mixing technique through (i) an injection molding (IM) process and (ii) the twin-screw extruder followed by an injection moulding process (TSE). It is observed that the mechanical properties of PP were found to be increased with MWCNTs concentration irrespective of the processing methods, where the optimum concentration was observed to be 1.5 wt. % of MWCNTs. It is also observed that the mechanical properties of polymer processed through TSE process was found to be less than that of the sample processed by IM process. However, an opposite trend was observed when the reinforcement was done. It is concluded that the PP/MWCNTs nanocomposites processed through TSE were found to have enhanced mechanical properties compared to that of the sample prepared through IM process.

scholarly journals Study of the Mechanical and Morphology Properties of Recycled HDPE Composite Using Rice Husk Filler

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Jia Ying Tong ◽  
Nishata Royan Rajendran Royan ◽  
Yong Chuen Ng ◽  
Mohd Hafizuddin Ab Ghani ◽  
Sahrim Ahmad
Keyword(s):  
Impact Strength ◽  
Rice Husk ◽  
Morphological Properties ◽  
Flexural Properties ◽  
Twin Screw Extrusion ◽  
Screw Extrusion ◽  
Twin Screw ◽  
The Impact ◽  
Extrusion Method ◽  
Recycled Hdpe

WPCs are being used in a large number of applications in the automotive, construction, electronic, and aerospace industries. There are an increasing number of research studies and developments in WPC technology involving rice husk as fillers. This study investigated the effects of different compositions of rice husk (RH) filler on the mechanical and morphological properties of recycled HDPE (rHDPE) composite. The composites were prepared with five different loading contents of RH fibers (0, 10, 20, 30, and 40 wt%) using the twin screw extrusion method. Maleic acid polyethylene (MAPE) was added as a coupling agent. Results showed that tensile and flexural properties improved with increasing RH loading. However, the impact strength of the composites decreased as the RH loading increased. SEM micrographs revealed good interfacial bonding between the fiber and polymer matrix.

A novel recycled polyethylene terephthalate/polyamide 11 (rPET/PA11) thermoplastic blend

2021 ◽  
pp. 147776062110010
Author(s):  
Zahid Iqbal Khan ◽  
Zurina Binti Mohamad ◽  
Abdul Razak Bin Rahmat ◽  
Unsia Habib ◽  
Nur Amira Sahirah Binti Abdullah
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Practical Implication ◽  
Polyamide 11 ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Electron Microscopy Analysis ◽  
The Impact

This work explores a novel blend of recycled polyethylene terephthalate/polyamide 11 (rPET/PA11). The blend of rPET/PA11 was introduced to enhance the mechanical properties of rPET at various ratios. The work’s main advantage was to utilize rPET in thermoplastic form for various applications. Three different ratios, i.e. 10, 20 and 30 wt.% of PA11 blend samples, were prepared using a twin-screw extruder and injection moulding machine. The mechanical properties were examined in terms of tensile, flexural and impact strength. The tensile strength of rPET was improved more than 50%, while the increase in tensile strain was observed 42.5% with the addition of 20 wt.% of PA11. The improved properties of the blend were also confirmed by the flexural strength of the blends. The flexural strength was increased from 27.9 MPa to 48 MPa with the addition of 30 wt.% PA11. The flexural strain of rPET was found to be 1.1%. However, with the addition of 10, 20 and 30 wt.% of PA11, the flexural strain was noticed as 1.7, 2.1, and 3.9% respectively. The impact strength of rPET/PA11 at 20 wt.% PA11 was upsurged from 110.53 to 147.12 J/m. Scanning electron microscopy analysis revealed a dispersed PA11 domain in a continuous rPET matrix morphology of the blends. This work practical implication would lead to utilization of rPET in automobile, packaging, and various industries.

scholarly journals Effect of Natural Fiber (NF) Mix on Mechanical Strength of NF Plastic Composites (NFPC)

2019 ◽  
Vol 9 (1) ◽  
pp. 5663-5667
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Natural Fiber ◽  
Fiber Type ◽  
Natural Fibers ◽  
Natural Fibre ◽  
Additional Advantage ◽  
Plastic Composites ◽  
Twin Screw ◽  
The Impact

Natural fibers from plants are gaining importance and may substitute wood in the production of wood plastic composites (WPC). To ensure continuity of fiber supply and sustainability of WPC industries, fibers of various types could be mixed together to obtain Mix WPC. However, research need to be carried out to identify the contribution of different fiber type collectively to the mechanical properties of Mix natural fiber polymer composite (NFPC). In this study, preliminary work on the use of natural fibre (NF) such as kenaf, sugar palm and pineapple leaf fibers in the preparation of Mix NFPC were carried out. Four different fiber mix samples with different fiber ratio and size were formulated using polypropylene (PP) as the polymer matrix. Montmorrilonite (MMT) filler was added at constant amount for enhancement of composite mechanical properties. Samples were mixed and prepared using a twin screw extruder and mini injection moulding resepectively. Individual fibers and NFPC prepared were characterized using thermogravimetric analyzer (TGA). Tensile, flexural and impact strength of the composites were determined. Generally, it was found that addition of fiber mix at 50% fiber loading enhance the tensile and flexural strength of the various NFPC with minimal exceptions. The impact strength of the composites were comparable to that of blank PP implying that addition of fiber gives additional advantage besides being eco-friendly. It was also found that higher kenaf loading and different size of fiber mix contribute positively to the various strengths measured. In addition to that, composition of individual fibers also contribute to the mechanical properties of the NFPCs

Impact strength and morphological properties of Kenaf/glass fibre/polyester hybrid composite for attenuator application

2020 ◽  
Vol 29 ◽  
pp. 119-122
Author(s):  
A.R.M. Nazim ◽  
M.N.M. Ansari ◽  
A. Atiqah
Keyword(s):  
Impact Strength ◽  
Glass Fibre ◽  
Hybrid Composite ◽  
Morphological Properties

The Effect of Thermal Aging on Mechanical Properties and Morphological Properties of Thermoplastic Vulcanizates Based on Natural Rubber and Polystyrene

2020 ◽  
Vol 990 ◽  
pp. 262-266
Author(s):  
Prathumrat Nu-Yang ◽  
Atiwat Wiriya-Amornchai ◽  
Jaehoon Yoon ◽  
Chainat Saechau ◽  
Poom Rattanamusik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Natural Rubber ◽  
Thermal Aging ◽  
Morphological Properties ◽  
Vulcanized Rubber ◽  
Thermoplastic Vulcanizates ◽  
Internal Mixer ◽  
Processing Properties

Thermoplastic vulcanizates or TPVs is a type of materials exhibiting excellent properties between thermoplastic and elastomer by combining the characteristics of vulcanized rubber with the processing properties of thermoplastics. This research aims to study the effect of thermal aging on the morphology and mechanical properties of thermoplastic vulcanizates (TPVs) based on a mixture of natural rubber (NR) and polystyrene (PS). TPVs samples were prepared using the internal mixer at a mass ratio of NR/PS 70/30, 50/50, 30/70 and 0/100. Tensile properties and impact strength showed that when the amount of NR increased tends of impact strength and elongation at break increased but tends of tensile strength decreased. On the other hand, tends of tensile strength for thermal aging at 70°C for 3 days increased when the amount of PS increase. The blending ratio of NR / PS at 70/30 is the best. It gave a worthy increase from 19.94 MPa to be 25.56 MPa (28.18%).

Structure and mechanical properties of HSS HS6-5-2- and HS12-1-5-5-type steel produced by modified powder injection moulding process

2004 ◽  
Vol 157-158 ◽  
pp. 658-668 ◽  
Author(s):  
L.A. Dobrzański ◽  
G. Matula ◽  
A. Várez ◽  
B. Levenfeld ◽  
J.M. Torralba
Keyword(s):  
Mechanical Properties ◽  
Injection Moulding ◽  
Powder Injection ◽  
Moulding Process ◽  
Type Steel ◽  
Powder Injection Moulding ◽  
Injection Moulding Process

MECHANICAL PROPERTIES AND SURFACE FREE ENERGY OF OIL PALM EMPTY FRUIT BUNCHES FIBRE REINFORCED BIOCOMPOSITES AS GLASS FIBRE SUBSTITUTION

2017 ◽  
Vol 79 (4) ◽  
Author(s):  
Gema Sukmawati Suryadi ◽  
Siti Nikmatin ◽  
Sudaryanto Sudaryanto ◽  
Irmansyah Irmansyah
Keyword(s):  
Mechanical Properties ◽  
Free Energy ◽  
Impact Strength ◽  
Surface Free Energy ◽  
Glass Fibre ◽  
Oil Palm ◽  
Short Fibre ◽  
Filler Materials ◽  
Empty Fruit Bunches ◽  
The Impact

Study of the size effect of natural fibre from oil palm empty fruit bunches (OPEFB) as filler, onto the mechanical and physical properties of fibre reinforced biocomposites based on recycled Acrylonitrile Butadiene Styrene (ABS) has been done. The OPEFB fibres were prepared by mechanical milling and sieving to obtain medium-fibre (20 mesh) and short-fibre (100 mesh). The biocomposites have been produced by extrusion using single-screw extruder method. Mechanical properties and S of biocomposites were evaluated and compared with glass fibre (GF) filled composite which is commonly used in plastics industrial applications. The result showed that the impact strength increased with the decreasing of OPEFB fibre size, while the Young’s modulus decreased. Other mechanical properties of biocomposites with short-fibre (RABS/SF) and medium-fibre (RABS/MF) filler were not significantly different at 95% confidence interval. Impact strength of short-fibre filled biocomposite was higher than glass fibre filled composites. The surface free energy of biocomposites lower than glass fibre filled composites, but its dispersive components are higher, indicating more hydrophobic feature of the surface. The fabricated micro-fibre of OPEFB can be used as viable alternative to substitute glass fibre as filler materials of composites.

Rheology, Morphology and Mechanical Properties of PA6/PP-g-MAH/POE Blends

2011 ◽  
Vol 366 ◽  
pp. 310-313
Author(s):  
Ming Tao Run ◽  
Meng Yao ◽  
Bing Tao Xing ◽  
Wen Zhou
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Screw Extruder ◽  
Reinforcing Agent ◽  
Twin Screw ◽  
Impact Tester ◽  
The Impact ◽  
Plastic Fluids ◽  
Morphology And Mechanical Properties ◽  
Toughening Agent

The rheology, morphology and mechanical properties of the PA6/PP-g-MAH/POE blends prepared by twin-screw extruder were studied by rheometer, scanning electron microscopy, universal tester and impact tester, respectively. The results suggest that the impact strength is improved by the POE acting as a toughening agent, while the compatibility of PA6 and POE is improved by the compatibilizer of PP-g-MAH. Furthermore, the PP-g-MAH component also acts as a reinforcing agent for decreasing the strength depression induced by the POE component. When POE content is about 9 wt% and PP-g-MAH content is about 10% in blends, the blend has the maximum tensile strength and impact strength. All melts of PA6/PP-g-MAH/POE blends are pseudo-plastic fluids. Both the POE and PP-g-MAH components can increase the apparent viscosity of the melt due to their facility of the linear molecular.

Effect of Compatibilizer Content on the Mechanical and Morphological Properties of PET/PP (70/30) Blends

2015 ◽  
Vol 735 ◽  
pp. 70-74
Author(s):  
Ibrahim Mohammed Inuwa ◽  
Azman Hassan ◽  
Sani Amril Samsudin
Keyword(s):  
Mechanical Properties ◽  
Triblock Copolymer ◽  
Standard Test ◽  
Morphological Properties ◽  
Screw Extruder ◽  
Elongation At Break ◽  
Young’S Moduli ◽  
Morphological Studies ◽  
Twin Screw ◽  
Pp Blends

This work investigates the effect of compatibilizer concentration on the mechanical properties of compatibilized polyethylene terephthalate (PET) /polypropylene (PP) blends. A blend containing 70 % (wt) PET, 30 % (wt) PP and 5 - 15 phr compatibilizers were compounded using counter rotating twin screw extruder and fabricated into standard test samples using injection molding. The compatibilizer used is styrene-ethylene-butylene-styrene grafted maleic anhydride triblock copolymer (SEBS-g-MAH). Morphological studies show that the particle size of the dispersed PP phase is dependent on the compatibilizer content up to 10 phr. Impact strength and elongation at break showed maximum values with the addition of 10 phr SEBS-g-MAH and a corresponding decrease in flexural and young’s moduli; and strengths.. Overall the mechanical properties of PET/PP blends depend on the control of the morphology of the blend and can be achieved by effective compatibilization using 10 phr SEBS-g-MAH.

Sign in / Sign up

Export Citation Format

Share Document