scholarly journals The Influence of an EPS Concrete Buffer Layer Thickness on Debris Dams Impacted by Massive Stones in the Debris Flow

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Xianbin Yu ◽  
Xiaoqing Chen ◽  
Wanyu Zhao ◽  
Jiangang Chen
Keyword(s):  
Debris Flow ◽  
Buffer Layer ◽  
Structural Design ◽  
Impact Force ◽  
Three Dimensional ◽  
Time History ◽  
Expanded Polystyrene ◽  
Debris Dams ◽  
The Impact ◽  
Debris Dam

The failure of debris dams impacted by the massive stones in a debris flow represents a difficult design problem. Reasonable materials selection and structural design can effectively improve the resistance impact performance of debris dams. Based on the cushioning properties of expanded polystyrene (EPS) concrete, EPS concrete as a buffer layer poured on the surface of a rigid debris dam was proposed. A three-dimensional numerical calculation model of an EPS concrete buffer layer/rigid debris dam was established. The single-factor theory revealed change rules for the thickness of the buffer layer concerning the maximal impact force of the rigid debris dam surface through numerical simulation. Moreover, the impact force-time/history curves under different calculation conditions for the rigid debris dam surface were compared. Simulation results showed that the EPS concrete buffer layer can not only effectively extend the impact time of massive stones affecting the debris dam but also reduce the impact force of the rigid debris dam caused by massive stones in the debris flow. The research results provide theoretical guidance for transferring the energy of the massive stone impact, creating a structural design and optimizing debris dams.

scholarly journals Dynamic Response Analysis of Retaining Dam under the Impact of Solid-Liquid Two-Phase Debris Flow Based on the Coupled SPH-DEM-FEM Method

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Bailong Li ◽  
Changming Wang ◽  
Yanying Li ◽  
Yiao Liu ◽  
Nan Jiang ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Debris Flow ◽  
Impact Force ◽  
Time History ◽  
Impact Behavior ◽  
Response Analysis ◽  
Two Phase ◽  
Fem Method ◽  
Solid Liquid ◽  
The Impact

Based on the coupled SPH-DEM-FEM numerical method, this paper analyzes the dynamic interaction of solid debris flow particle-liquid debris flow slurry-retaining dam in order to explore the dynamic response of retaining dam under the impact of the solid-liquid two-phase debris flow and delves into the process of the debris flow impact on the dam, the impact force of debris flow, and the elastic-plastic time-history characteristics of the dam under different slopes of trapezoidal grooves. The calculation results show that the coupled SPH-DEM-FEM method can vividly simulate the impact behavior of the solid-liquid two-phase debris flow on the dam, reproduce the impact, climbing, and siltation in the process of the debris flow impact; the dynamic time-history curve of the retaining dam is consistent with the law of the literature, and the result of the debris flow impact force obtained is close to that of the empirical formula. Moreover, this paper studies the impact force distribution of the debris flow impact process. The results have a certain reference value for the study of the dynamic response of the retaining dam under the impact of the solid-liquid two-phase debris flow and the engineering design of the debris flow-retaining dam.

Study on the Impact Properties of a New Debris Flow Dam Based on Steel-Concrete Composite Structure

2014 ◽  
Vol 638-640 ◽  
pp. 2056-2059 ◽  
Author(s):  
Ya Xiong Liang ◽  
Xiu Li Wang ◽  
Chang Wu ◽  
Zhi Gang Lv
Keyword(s):  
Finite Element ◽  
Debris Flow ◽  
Impact Force ◽  
Impact Load ◽  
Weak Link ◽  
Time History ◽  
Type Model ◽  
Finite Element Software ◽  
New Type ◽  
The Impact

The impact force is one of the most weak link of the dynamics studies of debris flow for many years. To make the structure or components are better able to suffer the impact load such as debris flow, explosions, a new debris flow dam is designed by introducing this new type model with spring. It is simulated under boulder impact by using finite element software LS-DYNA.The stress distribution, impact and displacement time history curve under typical conditions are obtained. The results show that the resist impact effect of new debris flow dam is very obvious.

scholarly journals Effects of Barrier Stiffness on Debris Flow Dynamic Impact—II: Numerical Simulation

Water ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 182
Author(s):  
Yu Huang ◽  
Xiaoyan Jin ◽  
Junji Ji
Keyword(s):  
Debris Flow ◽  
Smoothed Particle Hydrodynamics ◽  
Impact Force ◽  
Time History ◽  
Appreciable Effect ◽  
Engineering Structures ◽  
Dynamic Component ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
The Impact

The destructive and impactful forces of debris flow commonly causes local damage to engineering structures. The effect of a deformable barrier on the impact dynamics is important in engineering design. In this study, a flow–structure coupled with Smoothed Particle Hydrodynamics model was presented to investigate the effects of barrier stiffness on the debris impact. A comparison of the results of physical tests and simulation results revealed that the proposed smoothed particle hydrodynamics model effectively reproduces the flow kinematics and time history of the impact force. Even slight deflections of the deformable barrier lead to obvious attenuation of the peak impact pressure. Additionally, deformable barriers with lower stiffness tend to deform more downstream upon loading, shifting the deposited sand toward the active failure mode and generating less static earth pressure. When the debris flow has a higher frontal velocity, the impact force on the barrier is dominated by the dynamic component and there is an appreciable effect of the stiffness of the deformable barrier on load attenuation.

The Effects of Upstream Flexible Barrier on the Debris Flow Entrainment and Impact Dynamics on a Terminal Barrier

2021 ◽  
Author(s):  
Hervé Vicari ◽  
C.W.W. Ng ◽  
Steinar Nordal ◽  
Vikas Thakur ◽  
W.A. Roanga K. De Silva ◽  
...  
Keyword(s):  
Debris Flow ◽  
Debris Flows ◽  
Impact Force ◽  
Dynamic Pressure ◽  
Pressure Coefficient ◽  
Flexible Barrier ◽  
Impact Forces ◽  
Flexible Barriers ◽  
The Impact ◽  
Bed Entrainment

The destructive nature of debris flows is mainly caused by flow bulking from entrainment of an erodible channel bed. To arrest these flows, multiple flexible barriers are commonly installed along the predicted flow path. Despite the importance of an erodible bed, its effects are generally ignored when designing barriers. In this study, three unique experiments were carried out in a 28 m-long flume to investigate the impact of a debris flow on both single and dual flexible barriers installed in a channel with a 6 m-long erodible soil bed. Initial debris volumes of 2.5 m<sup>3</sup> and 6 m<sup>3</sup> were modelled. For the test setting adopted, a small upstream flexible barrier before the erodible bed separates the flow into several surges via overflow. The smaller surges reduce bed entrainment by 70% and impact force on the terminal barrier by 94% compared to the case without an upstream flexible barrier. However, debris overflowing the deformed flexible upstream barrier induces a centrifugal force that results in a dynamic pressure coefficient that is up to 2.2 times higher than those recommended in guidelines. This suggests that although compact upstream flexible barriers can be effective for controlling bed entrainment, they should be carefully designed to withstand higher impact forces.

scholarly journals Experimental Study of the Debris Flow Slurry Impact and Distribution

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Haixin Zhao ◽  
Lingkan Yao ◽  
Yong You ◽  
Baoliang Wang ◽  
Cong Zhang
Keyword(s):  
Debris Flow ◽  
Debris Flows ◽  
Impact Force ◽  
Influence Factors ◽  
Flume Experiment ◽  
Middle Point ◽  
Laboratory Flume ◽  
Critical Issues ◽  
Maximum Impact Force ◽  
The Impact

In this study, we present a new method to calculate debris flow slurry impact and its distribution, which are critical issues for designing countermeasures against debris flows. There is no unified formula at present, and we usually design preventive engineering according to the uniform distribution of the maximum impact force. For conducting a laboratory flume experiment, we arrange sensors at different positions on a dam and analyze the differences on debris flow slurry impact against various densities, channel slopes, and dam front angles. Results show that the force of debris flow on the dam distributes unevenly, and that the impact force is large in the middle and decreases gradually to the both sides. We systematically analyze the influence factors for the calculation of the maximum impact force in the middle point and give the quantitative law of decay from the middle to the sides. We propose a method to calculate the distribution of the debris flow impact force on the whole section and provide a case to illustrate this method.

scholarly journals Study on the Impact Resistance of Metal Flexible Net to Rock fall

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Gaosheng Wang ◽  
Yunhou Sun ◽  
Ao Zhang ◽  
Lei Zheng ◽  
Yuzheng Lv ◽  
...  
Keyword(s):  
Finite Element ◽  
Impact Force ◽  
Impact Resistance ◽  
Time History ◽  
Rock Fall ◽  
Fe Model ◽  
Element Analysis ◽  
Inclination Angles ◽  
Fall Protection ◽  
The Impact

Based on experiments and finite element analysis, the impact resistance of metal flexible net was studied, which can provide reference for the application of metal flexible net in rock fall protection. The oblique (30 degrees) impact experiment of metal flexible net was carried out, the corresponding finite element (FE) to the experiment was established, and the FE model was verified by simulation results to the experimental tests from three aspects: the deformation characteristics of metal flexible net, the time history curves of impact force on supporting ropes, and the maximum instantaneous impact force on supporting ropes. The FE models of metal flexible nets with inclination angles of 0, 15, 30, 45, 60, and 75 degrees were established, and the impact resistance of metal flexible nets with different inclination angles was analyzed. The research shows that the metal flexible net with proper inclination can bounce the impact rock fall out of the safe area and prevent rock fall falling on the metal flexible net, thus realizing the self-cleaning function. When the inclination angle of the metal flexible net is 15, 30, and 45 degrees, respectively, the bounce effect after impact is better, the remaining height is improved, the protection width is improved obviously, and the impact force is reduced. Herein, the impact force of rock fall decreases most obviously at 45 degrees inclination, and the protective performance is relatively good.

scholarly journals Debris Flow Damage Assessment by Considering Debris Flow Direction and Direction Angle of Structure in South Korea

Water ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 328 ◽  
Author(s):  
Dong Nam ◽  
Man-Il Kim ◽  
Dong Kang ◽  
Byung Kim
Keyword(s):  
South Korea ◽  
Debris Flow ◽  
Debris Flows ◽  
Impact Force ◽  
Mountainous Areas ◽  
Mountainous Regions ◽  
Impact Forces ◽  
The Impact

Recently, human and property damages have often occurred due to various reasons—such as landslides, debris flow, and other sediment-related disasters—which are also caused by regional torrential rain resulting from climate change and reckless development of mountainous areas. Debris flows mainly occur in mountainous areas near urban living communities and often cause direct damages. In general, debris flows containing soil, rock fragments, and driftwood temporarily travel down to lower parts along with a mountain torrent. However, debris flows are also often reported to stream down from the point where a slope failure or a landslide occurs in a mountain directly to its lower parts. The impact of those debris flows is one of the main factors that cause serious damage to structures. To mitigate such damage of debris flows, a quantitative assessment of the impact force is thus required. Moreover, technologies to evaluate disaster prevention facilities and structures at disaster-prone regions are needed. This study developed two models to quantitatively analyze the damages caused by debris flows on structures: Type-1 model for calculating the impact force, which reflected the flow characteristics of debris flows and the Type-2 model, which calculated the impact force based on the topographical characteristics of mountainous regions. Using RAMMS a debris flow runoff model, the impact forces assessed through Type-1 and Type-2 models were compared to check reliability. Using the assessed impact forces, the damage ratio of the structures was calculated and the amount of damage caused by debris flows on the structures was ultimately assessed. The results showed that the Type-1 model overestimated the impact force by 10% and the Type-2 model by 4% for Mt. Umyeon in Seoul, compared to the RAMMS model. In addition, the Type-1 model overestimated the impact force by 3% and Type-2 by 2% for Mt. Majeok in Chuncheon, South Korea.

Finite Element Analysis of a Single-Layer Reticulated Dome under Impact Loading

2010 ◽  
Vol 163-167 ◽  
pp. 327-331 ◽  
Author(s):  
Liang Zheng ◽  
Zhi Hua Chen
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Impact Force ◽  
Impact Load ◽  
Residual Deformation ◽  
Time History ◽  
Single Layer ◽  
Element Analysis ◽  
Deformation Stage ◽  
The Impact

Finite element model of both the single-layer Schwedler reticulated dome with the span of 50m and a Cuboid impactor were developed, incorporating ANSYS/LS-DYNA. PLASTIC_KINEMATIC (MAT_003) material model which takes stain rate into account was used to simulate steel under impact load. The automatic point to surface contact (NODES TO SURFACE) was applied between the dome and impact block. Three stages of time history curve of the impact force on the apex of the single-layer Scheduler reticulated dome including the impact stage, stable stalemate stage, the decaying stage were generalized according to its dynamic response. It must be pointed out that the peak of the impact force of the single-layer reticulated dome increase with the increase of the weight and the velocity of the impact block, but the change of the velocity of the impact block is more sensitive than the change of weight of the impact block for the effect of the peak of the impact force, and a platform value of the impact force of the single-layer reticulated dome change near a certain value, and the duration time of the impact gradually increase. Then four stages of time history curve of the impact displacement were proposed according to the dynamic response of impact on the apex of the single-layer reticulated dome based on numerical analysis. Four stages include in elastic deformation stage, plastic deformation stage, elastic rebound stage, free vibration stage in the position of the residual deformation.

scholarly journals Transient Response of an Impacted Beam and Indirect Impact Force Identification Using Strain Measurements

1994 ◽  
Vol 1 (3) ◽  
pp. 267-278 ◽  
Author(s):  
Hyungsoon Park ◽  
Youn-sik Park
Keyword(s):  
Impulse Response ◽  
Impact Force ◽  
Impulse Response Function ◽  
Time History ◽  
Impulse Response Functions ◽  
Transverse Impact ◽  
History Of ◽  
Convolution Approach ◽  
The Time Domain ◽  
The Impact

The impulse response functions (force-strain relations) for Euler–Bernoulli and Timoshenko beams are considered. The response of a beam to a transverse impact force, including reflection at the boundary, is obtained with the convolution approach using the impulse response function obtained by a Laplace transform and a numerical scheme. Using this relation, the impact force history is determined in the time domain and results are compared with those of Hertz's contact law. In the case of an arbitrary impact, the location of the impact force and the time history of the impact force can be found. In order to verify the proposed algorithm, measurements were taken using an impact hammer and a drop test of a steel ball. These results are compared with simulated ones.

Research of the Installation Angle of New Rotor Impact Plate Based on EDEM

2011 ◽  
Vol 80-81 ◽  
pp. 1133-1137
Author(s):  
De Rong Duan ◽  
Fang Zhao ◽  
Song Wang ◽  
Xian Xin Chen
Keyword(s):  
Dynamic Simulation ◽  
Impact Force ◽  
Three Dimensional ◽  
Substantial Effect ◽  
Maximum Speed ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Installation Angle ◽  
Impact Plate ◽  
The Impact

The three-dimensional model of new rotor was imported into EDEM for dynamic simulation, the maximum speed and force were analysied in the EDEM,indicating that the material along the deterministic trajectory collide with the impact plate for second acceleration after the first acceleration in new rotor, the velocity after second acceleration was 2.3 times than the first acceleration.The impact force and angle did not substantial effect on the second acceleration by comprehensive comparing,the 69m/s speed and less impact force were generated in the new rotor with 2° impact plate installation angle.

Sign in / Sign up

Export Citation Format

Share Document