scholarly journals Mining-Induced Stress-Fissure Field Evolution and the Disaster-Causing Mechanism in the High Gas Working Face of the Deep Hard Strata

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Litong Dou ◽  
Ke Yang ◽  
Wenjie Liu ◽  
Xiaolou Chi ◽  
Zhijie Wen
Keyword(s):  
Coal Seam ◽  
In Situ Monitoring ◽  
Gas Content ◽  
Hard Roof ◽  
Induced Stress ◽  
Field Evolution ◽  
Working Face ◽  
Dynamic Disaster ◽  
Seam Mining ◽  
The Impact

The compound dynamic disaster of coal and gas outbursts and rockburst is a typical hazard jeopardizing the mining of the high gas content coal seam under a hard roof condition. In this study, the hard roof’s mechanism inducing this hazard is analyzed. Physical analog modeling experiments and in situ monitoring of mining-induced stress were performed during coal seam mining under a hard roof condition. The pattern of hard roof breakage effect on the stress-fissure field evolution was revealed. The elastic energy was released and propagated on both sides immediately after the hard roof breaking, leading to energy accumulation. Meanwhile, expansive roof collapse resulted in the intense weighting of the working face and rockburst. Thus, the coal and gas outburst occurred under the joint action of the impact energy generated by breaking the hard roof and gas expansion energy. In other words, the compound dynamic disaster happened. Synergistic stereoextraction integrating cross-seam drilling and along-seam drilling was combined with deep hole advanced presplitting blasting technology to cope with the compound dynamic disaster in the high gas coal seam under a hard roof condition.

Dynamic Disaster Forecasting Technology of the Island Working Face in Outburst Coal Seam

2014 ◽  
Vol 962-965 ◽  
pp. 914-918
Author(s):  
Rong Xi Shen ◽  
En Yuan Wang ◽  
Shao Bin Hu ◽  
Jun Jun Feng
Keyword(s):  
Coal Seam ◽  
Electromagnetic Radiation ◽  
Gas Content ◽  
Ratio Method ◽  
Safety Level ◽  
Gas Concentration ◽  
Working Face ◽  
Dynamic Disaster ◽  
Outburst Coal Seam ◽  
Hydraulic Supports

Coal and gas outburst and rock burst are the main threats of the island working face in outburst coal seam. According to the characteristic of No. 11061 island face in outburst coal seam, Liangbei coal mine, China, the dynamic disaster mechanism of island working face in outburst coal seam was analyzed. Based on the monitor of gas concentration and electromagnetic radiation and hydraulic supports resistance in the 11061 island face, the comprehensive forecasting technology of the island face in outburst coal seam was built, then the critical values of gas concentration and electromagnetic radiation and hydraulic supports resistance are calculated by three-ratio method. Finally, the comprehensive forecasting technology is used in the island working face. The results show that the combined action of gas content and stress induces the dynamic disaster of the island working face in outburst coal seam, and the comprehensive forecasting technology can forecast accurately dynamic disaster in the 11061 island face, which has brought successful engineering experience and distinct economic benefit. It can improve significantly the mine production safety level to research the forecasting technology of the island working face in outburst coal seam.

Numerical Modeling of Subsidence-Induced Stress on the Pipeline in Steep Seam Mining

2013 ◽  
Vol 448-453 ◽  
pp. 3863-3868
Author(s):  
Guo Ming Cheng ◽  
Tong Zu Liu ◽  
Bin Zhi
Keyword(s):  
Numerical Modeling ◽  
Numerical Model ◽  
Coal Seam ◽  
Maximum Stress ◽  
Measurement Data ◽  
Steep Seam ◽  
Safe Operation ◽  
Induced Stress ◽  
Seam Mining ◽  
The Impact

In China, surface subsidence caused by steep coal seam mining has affected the safe operation of pipelines in recent years. The study site is one coal mine, where the gas pipeline from Shanshan to Urumqi is across. FLAC3D was adopted to study subsidence-induced stress on the pipeline, and the numerical model was calibrated with the measurement data. Visualization of alarm levels on the pipeline was obtained by integrating the usage of Fish function embedded in FLAC3D and Tecplot. The simulations reveal that the stress on the pipeline is closely related to the excavation depth. The stress on the pipeline increases with the excavation depth increasing when mining the 1st, 2nd, and 3rd levels, whereas the stress on the pipeline decreases slightly with the excavation depth increasing when mining the fourth, fifth, and sixth levels. The maximum stress on the pipeline occurs after mining the 3rd level. The possible damage to the pipe is at the upper-right side. Therefore, the results are helpful to prevent and reduce the impact of subsidence on the pipeline.

scholarly journals In Situ Studies on the Characteristics of Strata Structures and Behaviors in Mining of a Thick Coal Seam with Hard Roofs

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2470 ◽  
Author(s):  
Yiwen Lan ◽  
Rui Gao ◽  
Bin Yu ◽  
Xiangbin Meng
Keyword(s):  
Coal Seam ◽  
Cantilever Beam ◽  
Layer Structure ◽  
Test Method ◽  
Thick Coal Seam ◽  
Hard Roof ◽  
Working Face ◽  
High Layer ◽  
Seam Mining

The movements of overburden induced by mining a thick coal seam with a hard roof extend widely. The effects of breakages in the hard strata on the strata behaviors might vary with the overlying strata layers. For this reason, we applied a test method that integrated a borehole TV tester, borehole-based monitoring of strata movement, and monitoring of support resistance for an in situ investigation of a super-thick, 14–20 m coal seam mining in the Datong mining area in China. The results showed that the range of the overburden movement was significantly high, which could reach to more than 300 m. The key strata (KS) in the lower layer main roof were broken into a ‘cantilever beam and voussoir beam’ structure. This structure accounted for the ‘long duration and short duration’ strata behaviors in the working face. On the other hand, the hard KS in the upper layer broke into a ‘high layer structure’. The structural instability induced intensive and wide-ranging strata behaviors that lasted for a long time (two to three days). Support in the working face were over-pressured by large dynamic factors and were widely crushed, while the roadways were violently deformed. Hence, the structure of a thick coal seam with a hard roof after mining will form a ‘cantilever beam and voussoir beam and high layer structure’, which is unique to a large space stope.

scholarly journals The Mechanism and Control Technology of Strong Strata Behavior in Extra-Thick Coal Seam Mining Influenced by Overlying Coal Pillar

2019 ◽  
Vol 11 (1) ◽  
pp. 452-461
Author(s):  
Rui Gao ◽  
Tiejun Kuang ◽  
Yiwen Lan
Keyword(s):  
Coal Seam ◽  
Coal Pillar ◽  
In Situ Monitoring ◽  
Thick Coal Seam ◽  
Maximum Deformation ◽  
Working Face ◽  
Strata Behavior ◽  
Seam Mining ◽  
Roadway Deformation ◽  
And Control

Abstract This work aimed at revealing the mechanism of strong strata behavior in extra-thick coal seam mining which was influenced by an overlying coal pillar (OCP). To this end, the evolution characteristics of the stress and displacement in advance coal body of the working face were studied via numerical simulation. On this basis, the mechanism of strong strata behavior in working face affected by OCP was revealed. In situ monitoring also demonstrated that, as the working face mining near to the position of OCP, severe rib spalling and roadway deformation frequently appeared. The scheme of strengthening the hydraulic supports resistance and adding anchor cables was put forward to control the surrounding rocks in the stope. As a result, the maximum deformation of the roadway height was 0.66m and could completely meet the demands for safe mining. The study on the mechanism of strong strata behavior in working face and the strengthen supporting scheme would provide a theoretical basis for similar mining conditions, thus ensure safe and efficiency coal seam mining.

scholarly journals Investigation on the Ground Pressure Induced by Hard Roof Fracturing at Different Layers during Extra Thick Coal Seam Mining

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Rui Gao ◽  
Jingxuan Yang ◽  
Tiejun Kuang ◽  
Hongjie Liu
Keyword(s):  
Coal Seam ◽  
Physical Simulation ◽  
Similarity Criterion ◽  
Thick Coal Seam ◽  
Failure Characteristics ◽  
Hard Roof ◽  
Ground Pressure ◽  
Working Face ◽  
Seam Mining ◽  
Roadway Deformation

The fracturing of hard roofs in different layers would result in complex ground pressure on the working face, such as supports collapsed and severe roadway deformation. However, the mechanism of the ground pressure induced by hard roof fracturing in different layers is still unclear. In the paper, a physical model of a 20 m extrathick coal seam mined with hard roofs existing was established based on the physical simulation similarity criterion. The overburden fracturing structure, abutment stress distribution, and failure characteristics of the coal body were monitored by a noncontact strain measurement system and resistance strain gauges, to reveal the mechanism of ground pressure induced by hard roof fracturing. Furthermore, on-site measurement was used to monitor and analyze the ground pressure affected by hard roofs in different levels. The results provide a theoretical basis for the control of ground pressure in extrathick coal seam mining with hard roofs.

scholarly journals Comprehensive technical support for safe mining in ultra-close coal seams: A case study

2021 ◽  
pp. 014459872110093
Author(s):  
Wei Zhang ◽  
Jiawei Guo ◽  
Kaidi Xie ◽  
Jinming Wang ◽  
Liang Chen ◽  
...  
Keyword(s):  
Coal Seam ◽  
Technical Support ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Deformation Control ◽  
Hard Roof ◽  
Working Face ◽  
Close Coal Seams ◽  
Safe Mining

In order to mine the coal seam under super-thick hard roof, improve the utilization rate of resources and prolong the remaining service life of the mine, a case study of the Gaozhuang Coal Mine in the Zaozhuang Mining Area has been performed in this paper. Based on the specific mining geological conditions of ultra-close coal seams (#3up and #3low coal seams), their joint systematic analysis has been performed, with the focus made in the following three aspects: (i) prevention of rock burst under super-thick hard roof, (ii) deformation control of surrounding rock of roadways in the lower coal seam, and (iii) fire prevention in the goaf of working face. Given the strong bursting tendency observed in upper coal seam and lower coal seam, the technology of preventing rock burst under super-thick hard roof was proposed, which involved setting of narrow section coal pillars to protect roadways and interleaving layout of working faces. The specific supporting scheme of surrounding rock of roadways in the #3low1101 working face was determined, and the grouting reinforcement method of local fractured zones through Marithan was further proposed, to ensure the deformation control of surrounding rock of roadways in lower coal seams. The proposed fire prevention technology envisaged goaf grouting and spraying to plug leaks, which reduced the hazard of spontaneous combustion of residual coals in mined ultra-close coal seams. The technical and economic improvements with a direct economic benefit of 5.55 million yuan were achieved by the application of the proposed comprehensive technical support. The research results obtained provide a theoretical guidance and technical support of safe mining strategies of close coal seams in other mining areas.

scholarly journals Research on Control of Rib Spalling Disaster in the Three-Soft Coal Seam

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Feng Cui ◽  
Tinghui Zhang ◽  
Xiaoqiang Cheng
Keyword(s):  
Coal Seam ◽  
Field Experiments ◽  
Simulation Experiment ◽  
Current Status ◽  
Soft Coal ◽  
Grouting Pressure ◽  
Working Face ◽  
Coal Wall ◽  
Soft Coal Seam ◽  
Seam Mining

Rib spalling disaster at the coal mining faces severely restricted the safe and efficient output of coal resources. In order to solve this problem, based on the analysis of the current status of rib spalling in the three-soft coal seam 1508 Working Face of Heyang Coal Mine, a mechanical model of sliding-type rib spalling was established and the main influencing factors that affect rib spalling are given. The mechanism of grouting technology to prevent and control rib spalling has been theoretically analyzed. A similarity simulation experiment is used to analyze the change law of roof stress under the condition of three-soft coal seam mining. The optimal grouting pressure is determined by a numerical simulation experiment. And, silicate-modified polymer grouting reinforcement materials (SMPGMs) are used in field experiments. After twice grouting operations in the 1508 Working Face, the coal wall was changed from the original soft and extremely easy rib spalling to a straight coal wall and the amount of rib spalling has been reduced by 57.45% and 48.43, respectively. And, the mining height has increased by 0.16 m and 0.23 m, respectively. The experimental results show that the rib spalling disaster of the three-soft coal seam has been effectively controlled.

scholarly journals A Mechanical Model of the Overlying Rock Masses in Undersea Coal Mining and a Stress-Seepage Coupling Numerical Simulation

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jie Fang ◽  
Lei Tian ◽  
Yanyan Cai ◽  
Zhiguo Cao ◽  
Jinhao Wen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Coal Mining ◽  
Water Inrush ◽  
Mining Area ◽  
Analysis Model ◽  
Fractured Zones ◽  
Working Face ◽  
Seam Mining ◽  
Overlying Strata

The water inrush of a working face is the main hidden danger to the safe mining of underwater coal seams. It is known that the development of water-flowing fractured zones in overlying strata is the basic path which causes water inrushes in working faces. In the engineering background of the underwater mining in the Longkou Mining Area, the analysis model and judgment method of crack propagation were created on the basis of the Mohr–Coulomb criterion. Fish language was used to couple the extension model into the FLAC3d software, in order to simulate the mining process of the underwater coal seam, as well as to analyze the initiation evolutionary characteristics and seepage laws of the fractured zones in the overlying strata during the advancing processes of the working face. The results showed that, during the coal seam mining process, the mining fractured zones which had been caused by the compression-shear and tension-shear were mainly concentrated in the overlying strata of the working face. Also, the open-off cut and mining working face were the key sections of the water inrush in the rock mass. The condition of the water disaster was the formation of a water inrush channel. The possible water inrush channels in underwater coal mining are mainly composed of water-flowing fractured zones which are formed during the excavation processes. The numerical simulation results were validated through the practical engineering of field observations on the height of water-flowing fractured zone, which displayed a favorable adaptability.

Sign in / Sign up

Export Citation Format

Share Document