scholarly journals Efficacy of Natural Zeolite and Metakaolin as Partial Alternatives to Cement in Fresh and Hardened High Strength Concrete

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Iswarya Gowram ◽  
Beulah M ◽  
MR Sudhir ◽  
Mothi Krishna Mohan ◽  
Deekshith Jain
Keyword(s):  
High Strength Concrete ◽  
Natural Zeolite ◽  
Environmental Concern ◽  
Concrete Strength ◽  
High Strength ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Split Tensile Strength ◽  
Carbon Footprints ◽  
Strength Concrete

Urbanization and industrialization have dramatically increased the manufacture of cement causing substantial pollution of the environment. The primary global concern related to cement manufacture has been the management of the large carbon footprints. The usages of environmentally friendly cementitious materials in the construction of structures have proved to be a viable option to deal with this environmental concern. Therefore, it is necessary to further explore the usage of cementitious materials which can replace cement albeit partially. In this direction of research, two such cementitious materials, namely, natural zeolite and metakaolin have been investigated in this study. High-strength concrete M60 with natural zeolite and metakaolin as the partial replacements for the cement has been prepared in this work. Polycarboxylic ether-based superplasticizer solution has been used to enhance workability. The test specimen cast and cured for 3, 7, 28, 60, and 90 days at ambient room temperature has been tested for compressive strength, split tensile strength, and flexural strength as per the Indian standards. The optimum mix of high-strength concrete thus manufactured has met the Indian standards, and the combination of cement +5% natural zeolite +10% metakaolin has exhibited the highest compressive, split tensile, and flexural strengths at 90 days of curing. Natural zeolite and metakaolin when used in smaller proportions have increased the concrete strength, and these materials are recommended for partial replacement of cement.

Properties of High Strength Fibre Reinforced Concrete Using Ultra Fine Slag

2016 ◽  
Vol 857 ◽  
pp. 183-188
Author(s):  
C. Mohan Lal ◽  
Vontary Sai Srujan Reddy
Keyword(s):  
High Strength Concrete ◽  
Steel Fibre ◽  
High Strength ◽  
Target Strength ◽  
Partial Replacement ◽  
Fibre Reinforced Concrete ◽  
Test Results ◽  
Design Requirement ◽  
Split Tensile Strength ◽  
Strength Concrete

High strength concrete has become a design requirement in recent years due to increase in number of infrastructure projects. This paper presents the effect of incorporating Ultra Fine Slag (UFS) and steel fibre to obtain high strength concrete. To achieve target strength of about 80 MPa, it is proposed to the replacement of cement of 10%, 20% and 30% with UFS and incorporating 0.5% and 1.0% fibre in concrete. An experimental investigation is carried out to find the mechanical properties of the concrete. From the test results, it was observed that a compressive strength of 95 MPa was achieved at 30% replacement of cement with UFS and 1.0% fibre content. In addition, there was a significant improvement in split tensile strength and flexural strength of the concrete. This study demonstrates that a high strength concrete can be obtained from partial replacement of cement with UFS and addition of steel fibre.

scholarly journals Effects of Scrap Rubber TYRE Aggregates as Partial Replacement of Natural Aggregates in High Strength Concrete

2020 ◽  
Vol 9 (4) ◽  
pp. 2039-2043 ◽  
Keyword(s):  
High Strength Concrete ◽  
Research Work ◽  
High Strength ◽  
Partial Replacement ◽  
Experimental Program ◽  
Rubberized Concrete ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Strength Concrete ◽  
Natural Aggregates

This research work mainly focus on feasibility of incorporating rubber tyre cubical chips as a partial replacement or natural aggregates in concrete. Little work is done using rubberized concrete for normal strength. Here an attempt is made to compare the strength of high strength concrete for different % of rubber aggregates. Experimental program consists of testing the different parameter of the materials used like cement, sand, and aggregate. In the present investigation the mechanical strength like compressive strength, flexural strength, split tensile strength are compared with the rubberized concrete using 20mm single size rubber pieces as replacement to natural aggregate. Replacing by 5%, 10%, 15% and 20%. And there results were checked with reference to conventional concrete and the amount of variation in the strength is studied.

scholarly journals Experimental Study on the Torsional Behaviour of Prestressed HSC Hollow Beams

2020 ◽  
Vol 10 (2) ◽  
pp. 642 ◽  
Author(s):  
Luís Bernardo ◽  
Sérgio Lopes ◽  
Mafalda Teixeira
Keyword(s):  
Experimental Study ◽  
High Strength Concrete ◽  
Concrete Beams ◽  
Concrete Strength ◽  
High Strength ◽  
Experimental Program ◽  
Pure Torsion ◽  
Strength Concrete ◽  
Hollow Beams

This article describes an experimental program developed to study the influence of longitudinal prestress on the behaviour of high-strength concrete hollow beams under pure torsion. The pre-cracking, the post-cracking and the ultimate behaviour are analysed. Three tests were carried out on large hollow high-strength concrete beams with similar concrete strength. The variable studied was the level of longitudinal uniform prestress. Some important conclusions on different aspects of the beams’ behaviour are presented. These conclusions, considered important for the design of box bridges, include the influence of the level of prestress in the cracking and ultimate behaviour.

Bond behavior of high strength concrete under reversed pull-out cyclic loading

2002 ◽  
Vol 29 (2) ◽  
pp. 191-200 ◽  
Author(s):  
M Alavi-Fard ◽  
H Marzouk
Keyword(s):  
Cyclic Loading ◽  
Bond Strength ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Displacement Curve ◽  
Bond Slip ◽  
Strength Concrete ◽  
Pull Out ◽  
Normal Strength

Structures located in seismic zones require significant ductility. It is necessary to examine the bond slip characteristics of high strength concrete under cyclic loading. The cyclic bond of high strength concrete is investigated under different parameters, including load history, confining reinforcement, bar diameter, concrete strength, and the rate of pull out. The bond strength, cracking, and deformation are highly dependent on the bond slip behavior between the rebar and the concrete under cyclic loading. The results of cyclic testing indicate that an increase in cyclic displacement will lead to more severe bond damage. The slope of the bond stress – displacement curve can describe the influence of the rate of loading on the bond strength in a cyclic test. Specimens with steel confinement sustained a greater number of cycles than the specimens without steel confinement. It has been found that the maximum bond strength increases with an increase in concrete strength. Cyclic loading does not affect the bond strength of high strength concrete as long as the cyclic slip is less than the maximum slip for monotonic loading. The behavior of high strength concrete under a cyclic load is slightly different from that of normal strength concrete.Key words: bond, high strength, cyclic loading, bar spacing, loading rate, failure mechanism.

scholarly journals Cyclical Behavior of Concrete-Encased Composite Frame Joints with High Strength Concrete

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Lei Zeng ◽  
Zhenkun Cui ◽  
Yunfeng Xiao ◽  
Siqian Jin ◽  
Yuanyuan Wu
Keyword(s):  
Cyclic Loading ◽  
High Strength Concrete ◽  
Joint Strength ◽  
Concrete Strength ◽  
Outer Part ◽  
High Strength ◽  
Crack Pattern ◽  
Experimental Program ◽  
Strength Concrete ◽  
Composite Frame

This paper presents an application of high strength concrete to concrete-encased composite frame building based on an experimental program. The work emphasized joints behavior under reverse cyclic loading caused by earthquakes to provide information for seismic design. To investigate the internal mechanisms and seismic performance, cyclic loading tests were carried out on five half-scale interior joints. Two design variables were addressed in the research: concrete strength and axial column load. Frame joints performance including crack pattern, failure mode, deformation, ductility, strain distribution, and energy dissipation capacity was investigated. It was found that all joint specimens behaved in a manner with joint panel shear failure. Using high strength concrete increased the joint strength and had relatively little effect on the stiffness and ductility. The axial column load helped the joint strength by better mobilizing the outer part of the joint, but it had an obvious influence on the ductility and energy-dissipating capacity, which can be improved by providing enough transverse reinforcement. A typical crack pattern was also provided which can well reflect mechanical character and damage process. This research should contribute to the future engineering applications of high strength concrete to concrete-encased composite structure.

scholarly journals High-strength concrete eccentrically compressed elements

2019 ◽  
Vol 140 ◽  
pp. 02017
Author(s):  
Anastasia Vasilenko ◽  
Dmitry Chernogorsky ◽  
Dmitry Strakhov ◽  
Leonid Sinyakov
Keyword(s):  
Economic Efficiency ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Application Domain ◽  
Strength Concrete ◽  
Steel Ratio ◽  
Material Cost ◽  
Relative Eccentricity ◽  
Load Characteristics

The article is devoted to the analysis of technical and economic efficiency of application of high-strength concrete (HSC) in the eccentrically compressed columns. In the first part of the paper, the effect of concrete grade on in-creasing the column stiffness depending on steel ratio at different values of the relative eccentricity is considered. According to the results of the calculation, application of HSC is most effective at low values of the relative ec-centricity because increasing the concrete strength leads to more intensive increasing of column stiffness than increasing of steel ratio. In the second part of the paper, the material cost of the 1 linear meter of the column is calculated at the fixed value of column stiffness and application domain of HSC is defined in the case under consideration. In addition, load characteristics providing the efficiency of HSC application in the eccentrically compressed columns are determined.

Loading Process Simulation of GFRP Tube Filled with Steel-Reinforced High-Strength Concrete Columns Subjected to Eccentric Compression

2011 ◽  
Vol 71-78 ◽  
pp. 4203-4206
Author(s):  
Le Zhou ◽  
Hong Tao Liu
Keyword(s):  
High Strength Concrete ◽  
Slenderness Ratio ◽  
Concrete Strength ◽  
High Strength ◽  
Concrete Columns ◽  
Composite Columns ◽  
Strength Concrete ◽  
Finite Strip Method ◽  
Eccentric Compression ◽  
High Strength Concrete Columns

For the further study of bearing compressive capacity of GFRP tube filled with SHC（steel-reinforced high-strength concrete）columns subjected to eccentric compression, and analysis its whole bearing compressive process under eccentric compression. Based on the flat section assumption finite strip method, the calculating program of bearing eccentric compressive capacity of GFRP tube filled with SHC columns is proposed according to existing retrofit theory and related technical procedures. The relation curves of load-deformation is gotten using this calculating program, at the same time it can get the effect curves of concrete strength, slenderness ratio, eccentricity and containing bone rate to load-deformation. Calculations show that the ultimate bearing compressive capacity of composite column decreases with the increase of slenderness ratio, and elastic stage of component curve gradually shortens and stiffness gradually loses; The ultimate bearing compressive capacity of composite columns decreases with the increase of eccentricity; component ductility improves; the ultimate bearing compressive capacity of composite columns increases with the increase of concrete strength. The calculated results agree well with the experimental results and this study provides a basis for practical design.

scholarly journals Fire Performance of Columns Made of Normal and High Strength Concrete: A Comparative Analysis

2016 ◽  
Vol 711 ◽  
pp. 564-571 ◽  
Author(s):  
Thomas Gernay
Keyword(s):  
Bearing Capacity ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Strength Loss ◽  
Fire Performance ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Strength Concrete ◽  
The Impact

The use of high strength concrete (HSC) in multi-story buildings has become increasingly popular. Selection of HSC over normal strength concrete (NSC) allows for reducing the dimensions of the columns sections. However, this reduction has consequences on the structural performance in case of fire, as smaller cross sections lead to faster temperature increase in the section core. Besides, HSC experiences higher rates of strength loss with temperature and a higher susceptibility to spalling than NSC. The fire performance of a column can thus be affected by selecting HSC over NSC. This research performs a comparison of the fire performance of HSC and NSC columns, based on numerical simulations by finite element method. The thermal and structural analyses of the columns are conducted with the software SAFIR®. The variation of concrete strength with temperature for the different concrete classes is adopted from Eurocode. Different configurations are compared, including columns with the same load bearing capacity and columns with the same cross section. The relative loss of load bearing capacity during the fire is found to be more pronounced for HSC columns than for NSC columns. The impact on fire resistance rating is discussed. These results suggest that consideration of fire loading limits the opportunities for use of HSC, especially when the objective is to reduce the dimensions of the columns sections.

Sign in / Sign up

Export Citation Format

Share Document