scholarly journals Slot Loaded Capacitive fed Suspended RMSA with Meandered Ground Plane

2018 ◽  
Vol 7 (1) ◽  
pp. 49
Author(s):  
Ravi M. Yadahalli ◽  
Nandini M. Ammanagi
Keyword(s):  
Radiation Pattern ◽  
Ground Plane ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Small Patch ◽  
Rectangular Patch ◽  
Broadside Radiation ◽  
Coaxial Probe

In this paper, variations in the Capacitive fed suspended RMSA configurations have been proposed. Initially, the reference antenna consists of rectangular patch of size of (35.5 X 45.6) mm<sup>2</sup> and a small rectangular feed patch of size of (1.4 X 4) mm<sup>2 </sup>residing on the same substrate suspended above the ground plane. Coaxial probe is used to feed the small patch which in turn excites the radiator patch electromagnetically, yielding a large impedance bandwidth (BW) of 39%, with good gain and broadside radiation pattern.  By, meandering the ground plane of reference antenna with three rectangular slots, the prototype antenna is fabricated and measurement has been carried out to validate the result for compact broadband response. Later, by loading a pair of rectangular slots in the radiating patch of the reference antenna in addition to the rectangular slots in the ground plane, the prototype antenna is fabricated and measurement has been carried out to validate the result for compact dual band response.

Dual-band B-shaped antenna array for satellite applications

2020 ◽  
pp. 1-8
Author(s):  
Muhammad Mateen Hassan ◽  
Muzhair Hussain ◽  
Adnan Ahmed Khan ◽  
Imran Rashid ◽  
Farooq Ahmed Bhatti
Keyword(s):  
Antenna Array ◽  
Impedance Matching ◽  
Ground Plane ◽  
Bottom Layer ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Rectangular Patch ◽  
Full Wave ◽  
Satellite Applications ◽  
Strip Lines

Abstract The paper presents a 1 × 2 B-shaped antenna array for dual-band operation at 4 and 8 GHz. The antenna design consists of a rectangular patch with two annular-strip lines fabricated on the top layer and finite ground plane on the bottom layer. The array is formed by designing an optimum T-shaped microstrip line for impedance matching. The dimensions of the antenna array are 78 × 36 × 1.6 mm3. Full-wave simulations have been conducted and the measured results are in good consent with the simulated results. The measured impedance bandwidth (reference −10 dB) has been observed at 3.84–4.16 and 7.78–8.38 GHz. Measured peak gain and radiation efficiency at 4 and 8 GHz are 8.3, 9.4 dB and 82.5 and 81.2%, respectively.

scholarly journals A Compact Dual-Band Notched UWB Antenna for Wireless Applications

Micromachines ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 12
Author(s):  
Om Prakash Kumar ◽  
Pramod Kumar ◽  
Tanweer Ali
Keyword(s):  
Radiation Pattern ◽  
Group Delay ◽  
Ground Plane ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Linear Phase ◽  
Uwb Antenna ◽  
Rectangular Slot ◽  
Wireless Applications ◽  
Phase Group

This article presents the design and analysis of a V-shaped ultrawideband (UWB) antenna and dual-band UWB notch antenna. A rectangular slot is cut into a semicircular partial ground plane of the antenna to achieve ultrawide bandwidth. A U-shape slot is etched on a V-shaped patch that radiates, and an inverted U-shape parasitic resonator is placed beside the feedline to generate dual-band notch characteristics. The overall dimension of the proposed antenna is 28×23 mm2. The proposed UWB antenna has a gain of 9.8 dB, S11 < −10 dB, impedance bandwidth in the range of 3.4 to 12.3 GHz, response with a linear phase, group delay <1 ns, and stable radiation pattern. The UWB notch antenna shows strong rejection in the WLAN band from 5.15 to 5.8 GHz with a notch at 5.6 GHz and X band from 9.1 to 10.5 GHz with a sharp notch at 9.6 GHz, having a S11 < −10 dB impedance bandwidth ranging from 3.2 to 11.7 GHz. This antenna also exhibits a stable radiation pattern, group delay <1 ns, and linear phase response throughout the bandwidth except at the rejection frequencies.

scholarly journals Triangular Slot-Loaded Wideband Planar Rectangular Antenna Array for Millimeter-Wave 5G Applications

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 778
Author(s):  
Iftikhar Ahmad ◽  
Houjun Sun ◽  
Umair Rafique ◽  
Zhang Yi
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Ground Plane ◽  
Simulated Data ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Antenna ◽  
Rectangular Patch ◽  
Half Power

This paper presents a design of a triangular slot-loaded planar rectangular antenna array for wideband millimeter-wave (mm-wave) 5G communication systems. The proposed array realizes an overall size of 35.5 × 14.85 mm2. To excite the array elements, a four-way broadband corporate feeding network was designed and analyzed. The proposed array offered a measured impedance bandwidth in two different frequency ranges, i.e., from 23 to 24.6 GHz and from 26 to 45 GHz. The single-antenna element of the array consists of a rectangular patch radiator with a triangular slot. The partial ground plane was used at the bottom side of the substrate to obtain a wide impedance bandwidth. The peak gain in the proposed array is ≈12 dBi with a radiation efficiency of >90%. Furthermore, the array gives a half-power beamwidth (HPBW) of as low as 12.5°. The proposed array has been fabricated and measured, and it has been observed that the measured results are in agreement with the simulated data.

Dual Band Slot Antenna for 3.5 WiMAX and 5.8 WLAN

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Sahar Chagharvand ◽  
M. R. B. Hamid ◽  
M. R. Kamarudin ◽  
Mohsen Khalily
Keyword(s):  
Radiation Pattern ◽  
Coplanar Waveguide ◽  
Single Layer ◽  
Dual Band ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Gain ◽  
Dual Bandwidth ◽  
Electromagnetic Performance ◽  
Good Agreement

This paper presents a single layer planar slot antenna for dual band operation. The antenna is fed by a coplanar waveguide (CPW) with two inverted C-shaped resonators to achieve the dual band operation. The impedance bandwidth for ǀS11ǀ < -10dB is 14% in lower band and 7% in higher band. The antenna prototype’s electromagnetic performance, impedance bandwidth, radiation pattern, and antenna gain were measured. The proposed configuration offers a relatively compact, easy to fabricate and dual band performance providing gain between 2 and 4 dBi. The designed antenna has good dual bandwidth covering 3.5 WiMAX and 5.8 WLAN tasks. Experimental and numerical results also showed good agreement after comparison.

scholarly journals UWB elliptical patch monopole antenna with dual-band notched characteristics

2019 ◽  
Vol 9 (5) ◽  
pp. 3591
Author(s):  
A H Majeed ◽  
K H Sayidmarie
Keyword(s):  
Radiation Pattern ◽  
Ground Plane ◽  
Monopole Antenna ◽  
Experimental Results ◽  
Dual Band ◽  
New Approach ◽  
Compact Size

<p class="Default">In this paper, a new approach to the design of an UWB monopole antenna with dual band-notched characteristics is presented.   The antenna has the form of an elliptical monopole over a ground plane having an elliptical slot to achieve the UWB. The dual-band notch function is created by inserting a U-shaped and a C-shaped slots on the radiating patch, thus no extra size is needed. The proposed antenna shows a good omnidirectional radiation pattern across the band from 3.2 to more than 14 GHz. The dual band-rejection is for 4.88-5.79GHz centered at 5.4GHz and 7.21-8.46 GHz centered at 7.8 GHz. The antenna prototype using the FR-4 substrate with ε<sub>r</sub>=4.3 has a compact size of 25mm×25 mm ×1.45mm. The fabricated prototype showed experimental results comparable to those obtained from the simulations.</p>

scholarly journals Dual Band Notch, Compact, Low profile, Hybrid Ultra Wideband RDRA

2020 ◽  
Vol 10 (1) ◽  
pp. 166-169
Keyword(s):  
Radiation Pattern ◽  
Dielectric Resonator ◽  
Surface Current ◽  
Wide Band ◽  
Ultra Wideband ◽  
Dual Band ◽  
Ultra Wide Band ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Ground Structure

This paper presents a novel, compact Ultra Wide Band , Asymmetric Ring Rectangular Dielectric Resonator Antenna (ARRDRA), which is a unique combination of Thin Dielectric Resonator (DR), Fork shape patch and defective ground structure. The base of the proposed antenna is its Hybrid structure, which generates fundamental TM, TE and higher order modes that yields an impedance bandwidth of 119%. Proposed antenna provides a frequency range from 4.2 to 16.6 GHz with a stable radiation pattern and low cross polarization levels. Peak gain of 5.5 dB and average efficiency of 90% is obtained by the design. Antenna is elongated on a FR4 substrate of dimension 20 x 24x 2.168 mm3 and is particularly suitable for C band INSAT, Radio Altimeter, WLAN, Wi-Fi for high frequencies. Ease in fabrication due to simplicity, compactness, stable radiation pattern throughout the entire bandwidth are the key features of the presented design. Inclusion of Defective ground structure and asymmetric ring not only increases the bandwidth but also stabilize the gain and efficiency due to less surface current. Presented design launch an Ultra Wide Band antenna with sufficient band rejection at 4.48-5.34 and 5.64-8.33 GHz with stable radiation pattern and high gain.

scholarly journals Beamwidth-Enhanced Low-Profile Dual-Band Circular Polarized Patch Antenna for CNSS Applications

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Hongmei Liu ◽  
Chenhui Xun ◽  
Shaojun Fang ◽  
Zhongbao Wang
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Axial Ratio ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Coupled Line ◽  
Low Profile ◽  
Feed Network ◽  
Single Input ◽  
Half Power

A low-profile dual-band circular polarized (CP) patch antenna with wide half-power beamwidths (HPBWs) is presented for CNSS applications. Simple stacked circular patches are used to achieve dual-band radiation. To enhance the HPBW for the two operation bands, a dual annular parasitic metal strip (D-APMS) combined with reduced ground plane (R-GP) is presented. A single-input feed network based on the coupled line transdirectional (CL-TRD) coupler is also proposed to provide two orthogonal modes at the two frequency bands simultaneously. Experimental results show that the 10 dB impedance bandwidth is 32.7%. The 3 dB axial ratio (AR) bandwidths for the lower and upper bands are 4.1% and 6.5%, respectively. At 1.207 GHz, the antenna has the HPBW of 123° and 103° in the xoz and yoz planes, separately. And the values are 127° and 113° at 1.561 GHz.

Design of dual band-notched lamp-shaped antenna with UWB characteristics

2015 ◽  
Vol 9 (2) ◽  
pp. 395-402 ◽  
Author(s):  
Swati Yadav ◽  
Anil Kumar Gautam ◽  
Binod Kumar Kanaujia
Keyword(s):  
Electromagnetic Interference ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Ground Plane ◽  
Dual Band ◽  
Electrical Performance ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Impedance Mismatch ◽  
Rectangular Slot

To restrict electromagnetic interference at WiMAX (3.3–3.7 GHz) and wireless local area network (WLAN) (5.15–5.825 GHz) bands operating within ultra wide bandwidth (UWB) band, a novel design of lamp-shaped UWB microstrip antenna with dual band-notched characteristics is presented. The proposed antenna is composed of a lamp-shaped radiating patch with two rectangular ground planes on both the sides of the radiator with the gap of 0.57 mm. To improve impedance mismatch at middle frequencies, two triangular strips one at each of the ground plane are added; whereas a rectangular slot is etched in the radiating patch to remove impedance mismatch at higher frequencies of the UWB band. Furthermore, an L-shaped slot in the radiator and two L-shaped slots in the ground plane are used to restrict electromagnetic interference (EMI) at WiMAX and WLAN bands, respectively, without affecting the electrical performance of the UWB antenna. Effects of the key parameters on the frequency range of the notched bands are also investigated. The proposed design shows a measured impedance bandwidth of 12.5 GHz (2.7–14.4 GHz), with the two band-notched bands of 3.0–3.9 and 4.9–5.8 GHz. The antenna is suitable to be integrated within the portable UWB devices without EMI interference at WiMAX and WLAN bands.

scholarly journals A Compact Dielectric Resonator Antenna Excited by a Planar Monopole Patch for Wideband Applications

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Xuping Li ◽  
Yabing Yang ◽  
Fei Gao ◽  
Hanqing Ma ◽  
Xiaowei Shi
Keyword(s):  
Reflection Coefficient ◽  
Dielectric Resonator ◽  
Ground Plane ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
High Radiation ◽  
Ansoft Hfss ◽  
Measurement Results ◽  
Broadside Radiation ◽  
Operation Frequency

A compact dielectric resonator antenna (DRA) suitable for wideband applications is presented in this paper. The proposed antenna is mainly composed by a notched cylindrical dielectric resonator (DR) coated with a metal surface on the top and a finite ground plane where the presented DR is placed. This antenna is very simple in structure and has a very low overall height of0.14λminat its lowest operation frequency. A comprehensive parametric study is carried out based on Ansoft HFSS to optimize the bandwidth. The proposed antenna has been successfully simulated, optimized, fabricated, and measured. The measurement results demonstrate that the proposed design produces an impedance bandwidth of more than 75%, ranging from 2.9 GHz to 6.7 GHz for the reflection coefficient less than −10 dB. In particular, consistent broadside radiation patterns, stable gain, and high radiation efficiency are also obtained within the operation frequency band.

Circularly Polarized Rectangular Microstrip Patch Antenna with Finite Ground Plane

2015 ◽  
Vol 4 (2) ◽  
pp. 74
Author(s):  
Sanyog Rawat ◽  
Kamlesh Kumar Sharma
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Axial Ratio ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Microstrip Patch ◽  
Rectangular Patch

<p class="Abstract"><span style="font-weight: normal;">In this paper a new geometry of patch antenna is proposed with improved bandwidth and circular polarization. The radiation performance of circularly polarized rectangular patch antenna is investigated by applying IE3D simulation software and its performance is compared with that of conventional rectangular patch antenna.</span> <span style="font-weight: normal;">Finite Ground truncation technique is used to obtain the desired results. The simulated return loss, axial ratio and smith chart with frequency for the proposed antenna is reported in this paper. It is shown that by selecting suitable ground-plane dimensions, air gap and location of the slits, the impedance bandwidth can be enhanced upto 10.15 % as compared to conventional rectangular patch (4.24%) with an axial ratio bandwidth of 4.05%.</span></p><p> </p><p> </p>

Sign in / Sign up

Export Citation Format

Share Document