Study on Hot Deformation Behavior of Spray-Forming and Nano-Sized Al–Cu–Mg Alloy

2021 ◽  
Vol 21 (6) ◽  
pp. 3274-3282
Author(s):  
Tong Shen ◽  
Caihe Fan ◽  
Ling Ou ◽  
Zeyi Hu ◽  
Jianjun Yang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Power Dissipation ◽  
Deformation Behavior ◽  
Dynamic Recovery ◽  
High Strain ◽  
Electron Backscatter Diffraction ◽  
Spray Forming ◽  
Mg Alloy ◽  
Strain Rates ◽  
Backscatter Diffraction

Spray-forming Al–Cu–Mg alloy was compressed to 70% deformation at 300–450 °C and strain rates of 0.01–10.00 s−1 on a Gleeble-3180 system. The microstructures of the hot deformed, sprayforming, nano-sized Al–Cu–Mg alloys were studied through electron backscatter diffraction. Constitutive equation and parameter Z were established to describe the deformation behavior of the alloy at high temperature, and the Q value was 155.67 KJ·mol−1. 3D power dissipation and processing maps were analyzed under strain values of 0.3, 0.6, 0.9, and 1.2. When the strain was increased from 0.6 to 0.9, the processing performance changed remarkably. Dynamic recovery occurred at low temperature and high strain rate, whereas dynamic recrystallization took place at increased temperature and low strain rate. The region in 400–450 °C and 0.01 s−1–0.08 s−1 exhibited an improved processing performance.

scholarly journals High Strain Rate Properties of Various Forms of Ti6Al4V(ELI) Produced by Direct Metal Laser Sintering

2021 ◽  
Vol 11 (17) ◽  
pp. 8005
Author(s):  
Amos Muiruri ◽  
Maina Maringa ◽  
Willie du Preez
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Electron Backscatter Diffraction ◽  
Dynamic Strength ◽  
Strain Rates ◽  
Direct Metal Laser Sintering ◽  
Heat Treated ◽  
Electron Backscatter ◽  
Backscatter Diffraction

For analysis of engineering structural materials to withstand harsh environmental conditions, accurate knowledge of properties such as flow stress and failure over conditions of high strain rate and temperature plays an essential role. Such properties of additively manufactured Ti6Al4V(ELI) are not adequately studied. This paper documents an investigation of the high strain rate and temperature properties of different forms of heat-treated Ti6Al4V(ELI) samples produced by the direct metal laser sintering (DMLS). The microstructure and texture of the heat-treated samples were analysed using a scanning electron microscope (SEM) equipped with an electron backscatter diffraction detector for electron backscatter diffraction (EBSD) analysis. The split Hopkinson pressure bar (SHPB) equipment was used to carry out tests at strain rates of 750, 1500 and 2450 s−1, and temperatures of 25, 200 and 500 °C. The heat-treated samples of DMLS Ti6Al4V(ELI) alloys tested here were found to be sensitive to strain rate and temperature. At most strain rates and temperatures, the samples with finer microstructure exhibited higher dynamic strength and lower strain, while the dynamic strength and strain were lower and higher, respectively, for samples with coarse microstructure. The cut surfaces of the samples tested were characterised by a network of well-formed adiabatic shear bands (ASBs) with cracks propagating along them. The thickness of these ASBs varied with the strain rate, temperature, and various alloy forms.

Dynamic Deformation Behavior of As-Extruded Mg-Gd-Y Magnesium Alloy and the Microstructural Evolution

2011 ◽  
Vol 284-286 ◽  
pp. 1579-1583
Author(s):  
Ping Li Mao ◽  
Zheng Liu ◽  
Chang Yi Wang ◽  
Feng Wang
Keyword(s):  
Magnesium Alloy ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Deformation ◽  
Strain Rates ◽  
Compression Axis ◽  
Deformation Localization ◽  
Dynamic Deformation Behavior

The dynamic deformation behavior of an as-extruded Mg-Gd-Y magnesium alloy was studied by using Split Hopkinson Pressure Bar (SHPB) apparatus under high strain rates of 102 s-1 to 103s-1 in the present work, in the mean while the microstructure evolution after deformation were inspected by OM and SEM. The results demonstrated that the material is not sensitive to the strain rate and with increasing the strain rate the yield stress of as-extruded Mg-Gd-Y magnesium alloy has a tendency of increasing. The microstructure observation results shown that several deformation localization areas with the width of 10mm formed in the strain rates of 465s-1 and 2140s-1 along the compression axis respectively, and the grain boundaries within the deformation localization area are parallel with each other and are perpendicular to the compression axis. While increasing the strain rate to 3767s-1 the deformation seems become uniform and all the grains are compressed flat in somewhat. The deformation mechanism of as-extruded Mg-Gd-Y magnesium alloy under high strain rate at room temperature was also discussed.

scholarly journals Effect of strain rate on α-lath thickness of TC17 alloy after deformation and subsequent heat treatment

2020 ◽  
Vol 321 ◽  
pp. 13003
Author(s):  
Zimin Lu ◽  
Jiao Luo ◽  
Miaoquan Li
Keyword(s):  
Heat Treatment ◽  
Strain Rate ◽  
Electron Backscatter Diffraction ◽  
Phase Region ◽  
Subsequent Heat Treatment ◽  
Strain Rates ◽  
Optical Micrograph ◽  
Β Phase ◽  
Electron Backscatter ◽  
Backscatter Diffraction

Effect of strain rate on α-lath thickness of TC17 alloy with a basketweave microstructure was studied in the present work. For this purpose, this alloy was deformed in the β phase region and subsequently soluted and aged in α+β phase region. Moreover, optical micrograph (OM) and electron backscatter diffraction (EBSD) were applied to analyze the change of lath thickness at different strain rates. The result showed that α-lath thickness increased with increasing strain rate. This phenomenon was possibly attributed to the higher degree of variant selection (DVS) at higher strain rate (0.1 s-1). The higher DVS was beneficial for the formation of parallel α-lath colonies during cooling after deformation. And, these parallel α-lath colonies would more easily grow up and coarsen during subsequent heat treatment. Therefore, α-lath at higher strain rate is more thick.

Research on Numerical Algorithm of Constitutive Equation under High Speed Deformation in Hadfield Steel

2012 ◽  
Vol 562-564 ◽  
pp. 688-692 ◽  
Author(s):  
Deng Yue Sun ◽  
Jing Li ◽  
Fu Cheng Zhang ◽  
Feng Chao Liu ◽  
Ming Zhang
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Speed ◽  
High Strain ◽  
Equivalent Stress ◽  
Hadfield Steel ◽  
Stress And Strain ◽  
Strain Rates ◽  
The Finite Element Method

The influence of the strain rate on the plastic deformation of the metals was significant during the high strain rate of loading. However, it was very difficult to obtain high strain rate data (≥ 104 s-1) by experimental techniques. Therefore, the finite element method and iterative method were employed in this study. Numerical simulation was used to characterise the deformation behavior of Hadfield steel during explosion treatment. Base on experimental data, a modified Johnson-Cook equation for Hadfield steel under various strain rate was fitted. The development of two field variables was quantified during explosion hardening: equivalent stress and strain rates.

High Strain Rate Blow Formability of Newly Developed Al-Mg-High-Mn Alloy

2012 ◽  
Vol 735 ◽  
pp. 271-277 ◽  
Author(s):  
Tomoyuki Kudo ◽  
Akira Goto ◽  
Kazuya Saito
Keyword(s):  
Grain Size ◽  
High Strain Rate ◽  
Strain Rate ◽  
Mass Production ◽  
High Strain ◽  
Mg Alloy ◽  
Strain Rates ◽  
Fine Grain ◽  
Aa5083 Alloy ◽  
Complex Parts

Blow forming accompanied with superplasticity makes possible the forming of complex parts, which cannot be formed by cold press forming. The conventional superplastic AA5083 alloy ‘ALNOVI-1’ developed by the Furukawa-Sky Aluminum Corp. shows high superplasticity because of its fine grain and is widely used for blow forming. However, for mass production of components, an Al-Mg alloy with finer-sized grains is needed. In this research, the newly developed high Mn version of the Al-Mg alloy ‘ALNOVI-U’ is used, and this material possesses grains finer than those of the conventional AA5083 alloy. The effects of finer grain size on the blow formability at high strain rates over 10-2/s and the properties of the resulting moldings were studied.

Dynamic Testing at High Strain Rates of AZ31 Magnesium Alloys on SHPB Equipment

2013 ◽  
Vol 303-306 ◽  
pp. 2648-2651
Author(s):  
Xu Qing Chang ◽  
Tie Hua Ma
Keyword(s):  
Strain Rate ◽  
Optical Microscopy ◽  
Strain Hardening ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Mg Alloy ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
High Strain Rates ◽  
Az31 Mg Alloy

The mechanical behaviour of as-cast AZ31 Mg alloy has been investigated at strain rates up to 2.0×103s-1. Dynamic tests were carried out at room temperature using a Split Hopkinson Pressure Bar (SHPB) apparatus. Microstructural characteristic were analysed by Image MAT A1 optical microscopy. The results demonstrated that AZ31 Mg alloy exhibited obvious yield phenomena and strain hardening behaviour at high strain rates. The basically same curvature of stress-strain curves exhibited an similar strain hardening rate. The dynamic yield strength changes little and the peak stress increases with the strain rates. An examination by optical microscopy after high strain rate deformation reveals the occurrence of twinning and twin area percentage increases with the strain rate increasing.

scholarly journals Hot Deformation Behavior and Constitutive Modeling of H13-Mod Steel

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 846 ◽  
Author(s):  
Changmin Li ◽  
Yuan Liu ◽  
Yuanbiao Tan ◽  
Fei Zhao
Keyword(s):  
Constitutive Equation ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
High Strain ◽  
Flow Behavior ◽  
Peak Stress ◽  
Strain Rates ◽  
Hot Deformation Behavior ◽  
Stress Strain

The H13-mod steel optimized by composition and heat treatment has reached the performance index of the shield machine hob. The hot deformation behavior of the H13-mod steel was investigated by compression tests in the temperature range from 900 to 1150 °C and the strain rate range from 0.01 to 10 s−1. The true stress-strain curve showed that the rising stress at the beginning of deformation was mainly caused by work hardening. After the peak stress was attained, the curve drop and the flow softening phenomenon became more obvious at low strain rates. The flow behavior of the H13-mod steel was predicted by a strain-compensated Arrhenius-type constitutive equation. The relationship between the material constant in the Arrhenius-type constitutive equation and the true strain was established by a sixth-order polynomial. The correlation coefficient between the experimental value and the predicted value reached 0.987, which indicated that the constitutive equation can accurately estimate the flow stress during the deformation process. A good linear correlation was achieved between the peak stress (strain), critical stress (strain) and the Zener‒Hollomon parameters. The processing maps of the H13-mod steel under different strains were established. The instability region was mainly concentrated in the high-strain-rate region; however, the microstructure did not show any evidence of instability at high temperatures and high strain rates. Combined with the microstructure and electron backscattered diffraction (EBSD) test results under different deformations, the optimum hot working parameters were concluded to be 998–1026 °C and 0.01–0.02 s−1 and 1140–1150 °C and 0.01–0.057 s−1.

Deformation Behavior of Polycrystalline Fe-Ga-B Alloy at Elevated Temperature

2011 ◽  
Vol 687 ◽  
pp. 467-473
Author(s):  
Ji Heng Li ◽  
Xue Xu Gao ◽  
Jie Zhu ◽  
Xiaoqian Bao ◽  
Mao Cai Zhang
Keyword(s):  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Dynamic Recovery ◽  
High Strain ◽  
Strain Rate Range ◽  
Test Machine ◽  
Compression Tests ◽  
Simulation Test ◽  
Deformation Activation Energy

In this work, the hot deformation behavior of Fe83Ga17alloy with 1.0 at.% B addition was investigated by plane strain compression tests on a Gleeble-1500 hot simulation test machine in the deformation temperature range of 350 to 900 °C. The effects of strain rate range 0.1-10 s-1on flow stress and microstructure were also studied. It was indicated that as the temperature increases, significant softening of the material occurred, and significant dynamic recovery at low strain rate (0.1 s-1) and recrystallization at high strain rate (10 s-1) occurred during deformation at 900 °C. The results also suggested that deformation mechanism under low temperature (~500°C) was twinning. The hot deformation activation energy (Q) of the Fe83Ga17with 1.0 at.%B alloy was calculated to be 295.3 kJ/mol.

scholarly journals Comparison in Deformation Behavior, Microstructure, and Failure Mechanism of Nickel Base Alloy 625 under Two Strain Rates

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2652
Author(s):  
Meng Liu ◽  
Quanyi Wang ◽  
Yifan Cai ◽  
Dong Lu ◽  
Tianjian Wang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Base Alloy ◽  
Inconel 625 ◽  
Tensile Fracture ◽  
Nickel Base Superalloy ◽  
Strain Rates ◽  
Tensile Fracture Surface ◽  
Nickel Base

Tensile deformation behavior and microstructure of nickel-base superalloy Inconel 625 are investigated under different strain rates of 5 × 10−4 s−1 and 5 × 10−5 s−1. According to the experimental results, yield strength and ultimate tensile strength of the alloy increase with the increase in strain rate in room temperature. Microstructure results indicate that the size of dimples is smaller in the tensile fracture surface at low strain rate than the high strain rate, and the number of dimples is also related to the strain rates and twins appear earlier in the specimens with higher strain rates. Apart from Hollomon and Ludwik functions, a new formula considering the variation trend of strength in different deformation stages is deduced and introduced, which fit closer to the tensile curves of the 625 alloy used in the present work at both strain rates. Furthermore, the Schmid factors of tensile samples under two strain rates are calculated and discussed. In the end, typical work hardening behavior resulting from the dislocations slip behavior under different strain rates is observed, and a shearing phenomenon of slip lines cross through the δ precipitates due to the movement of dislocations is also be note.

Sign in / Sign up

Export Citation Format

Share Document