High Strain Rate Blow Formability of Newly Developed Al-Mg-High-Mn Alloy

2012 ◽  
Vol 735 ◽  
pp. 271-277 ◽  
Author(s):  
Tomoyuki Kudo ◽  
Akira Goto ◽  
Kazuya Saito
Keyword(s):  
Grain Size ◽  
High Strain Rate ◽  
Strain Rate ◽  
Mass Production ◽  
High Strain ◽  
Mg Alloy ◽  
Strain Rates ◽  
Fine Grain ◽  
Aa5083 Alloy ◽  
Complex Parts

Blow forming accompanied with superplasticity makes possible the forming of complex parts, which cannot be formed by cold press forming. The conventional superplastic AA5083 alloy ‘ALNOVI-1’ developed by the Furukawa-Sky Aluminum Corp. shows high superplasticity because of its fine grain and is widely used for blow forming. However, for mass production of components, an Al-Mg alloy with finer-sized grains is needed. In this research, the newly developed high Mn version of the Al-Mg alloy ‘ALNOVI-U’ is used, and this material possesses grains finer than those of the conventional AA5083 alloy. The effects of finer grain size on the blow formability at high strain rates over 10-2/s and the properties of the resulting moldings were studied.

Hot Deformation Resistance of an AA5083 Alloy under High Strain Rate

2014 ◽  
Vol 626 ◽  
pp. 553-560
Author(s):  
Shi Rong Chen ◽  
Chung Yung Wu ◽  
Yi Liang Ou ◽  
Yen Liang Yeh
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Hot Deformation ◽  
High Strain ◽  
Load Cell ◽  
Deformation Resistance ◽  
Strain Rates ◽  
Flow Curves ◽  
Aa5083 Alloy ◽  
Temperature Strain

Axisymmetric compression tests using Gleeble 3800 simulator were carried out to investigate hot deformation behaviors of an AA5083 alloy under high strain rate conditions. Sharp temperature rise and load cell ringing characterized by severely vibrational load responses were encountered at strain rates higher than 20 s-1 and sample buckling occurred at low temperatures. The load cell ringing was corrected using a moving average method with a two-way filtering operation to correct phase distortion. Isothermal flow curves were obtained by fitting the instantaneous temperatures into a binomial function, while buckling was correlated with sample height and Young’s modulus. After the corrections, hyperbolic sine equation was successfully used to extend from the hot tensile data having strain rates lower than 3 s-1 to 100 s-1. Quantitative analyses were accordingly made over the effects of temperature, strain rate and work hardening behavior on the flow curves. The previous constitutive equation in form of temperature, strain and strain rate was modified to predict the hot deformation resistance of the AA5083 alloy at temperatures of 250-450oC under the high strain rate operations.

Impact tensile behavior and frequency response of 3D braided composites

2011 ◽  
Vol 82 (3) ◽  
pp. 280-287 ◽  
Author(s):  
Xuehui Gan ◽  
Jianhua Yan ◽  
Bohong Gu ◽  
Baozhong Sun
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Strain ◽  
Tensile Modulus ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Braided Composites ◽  
3D Braided Composites

The uniaxial tensile properties of 4-step 3D braided E-glass/epoxy composites under quasi-static and high-strain rate loadings have been investigated to evaluate the tensile failure mode at different strain rates. The uniaxial tensile properties at high strain rates from 800/s to 2100/s were tested using the split Hopkinson tension bar (SHTB) technique. The tensile properties at quasi-static strain rate were also tested and compared with those in high strain rates. Z-transform theory is applied to 3D braided composites to characterize the system dynamic behaviors in frequency domain. The frequency responses and the stability of 3D braided composites under quasi-static and high-strain rate compression have been analyzed and discussed in the Z-transform domain. The results indicate that the stress-strain curves are rate sensitive, and tensile modulus, maximum tensile stress and corresponding tensile strain are also sensitive to the strain rate. The tensile modulus, maximum tensile stress of the 3D braided composites are linearly increased with the strain rate. With increasing of the strain rate (from 0.001/s to 2100/s), the tensile failure of the 3D braided composite specimens has a tendency of transition from ductile failure to brittle failure. The magnitude response and phase response is very different in quasi-static loading with that in high-strain rate loading. The 3D braided composite system is more stable at high strain rate than quasi-static loading.

Research on Numerical Algorithm of Constitutive Equation under High Speed Deformation in Hadfield Steel

2012 ◽  
Vol 562-564 ◽  
pp. 688-692 ◽  
Author(s):  
Deng Yue Sun ◽  
Jing Li ◽  
Fu Cheng Zhang ◽  
Feng Chao Liu ◽  
Ming Zhang
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Speed ◽  
High Strain ◽  
Equivalent Stress ◽  
Hadfield Steel ◽  
Stress And Strain ◽  
Strain Rates ◽  
The Finite Element Method

The influence of the strain rate on the plastic deformation of the metals was significant during the high strain rate of loading. However, it was very difficult to obtain high strain rate data (≥ 104 s-1) by experimental techniques. Therefore, the finite element method and iterative method were employed in this study. Numerical simulation was used to characterise the deformation behavior of Hadfield steel during explosion treatment. Base on experimental data, a modified Johnson-Cook equation for Hadfield steel under various strain rate was fitted. The development of two field variables was quantified during explosion hardening: equivalent stress and strain rates.

Microstructural Design for Attaining High-Strain-Rate Superplasticity in Oxide Materials

2006 ◽  
Vol 45 ◽  
pp. 923-932
Author(s):  
Keijiro Hiraga ◽  
Byung Nam Kim ◽  
Koji Morita ◽  
Tohru Suzuki ◽  
Yoshio Sakka
Keyword(s):  
Grain Size ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Spinel Phase ◽  
Tetragonal Zirconia ◽  
Secondary Phases ◽  
Cavitation Damage ◽  
Size Refinement ◽  
Dynamic Grain Growth

Factors limiting the strain rate of superplastic deformation in oxide ceramics are discussed from existing knowledge about the mechanisms of high-temperature plastic deformation and intergranular cavitation. The discussion leads to the following guide: simultaneously controlling the initial grain size, diffusivity, dynamic grain growth, homogeneity of microstructure and the number of residual defects is essential to attain high-strain-rate superplasticity. Along this guide, high-strain-rate superplasticity (HSRS) is attainable in some oxides consisting of tetragonal zirconia, α-alumina and a spinel phase: tensile ductility reached 300-2500% at a strain rate of 0.01-1.0 s-1. Post-deformation microstructure indicates that some secondary phases may suppress cavitation damage and thereby enhance HSRS. The guide is also essential to lower the limit of deformation temperature for a given strain rate. In monolithic tetragonal zirconia, grain-size refinement combined with doping of aliovalnt cations such as Mg2+, Ti4+ and Al3+ led to HSRS at 1350 °C.

Numerical Simulation of Hot High Strain Rate Torsion Tests for Al-Based Alloys

2019 ◽  
Vol 822 ◽  
pp. 66-71
Author(s):  
Anton Naumov ◽  
Anatolii Borisov ◽  
Anastasiya Y. Doroshchenkova
Keyword(s):  
Numerical Simulation ◽  
High Strain Rate ◽  
Strain Rate ◽  
Visual Analysis ◽  
Physical Simulation ◽  
High Strain ◽  
Torsion Test ◽  
Strain Rates ◽  
Deform 3D

The present research describes the comparison of numerical and physical simulation of hot high strain rate torsion tests for Al-based alloys in order to clarify the accuracy of calculations using basic grades of materials in Deform-3DTM software. A comparative visual analysis of the results is presented. Obtained data on the distribution of temperatures, strains, stresses and strain rates during the torsion test are discussed.

Medium to High Strain-Rate Characterization of Lead Free Solder Alloys Through Metal Cutting Experiments

2019 ◽  
Author(s):  
Yuvraj Singh ◽  
Anirudh Udupa ◽  
Srinivasan Chandrasekar ◽  
Ganesh Subbarayan
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Metal Cutting ◽  
High Strain ◽  
Lead Free ◽  
Strain Rates ◽  
Lead Free Solder ◽  
Orthogonal Metal Cutting ◽  
Free Solder

Abstract Studies on medium to high strain-rate characterization (≥ 0.1s−1) of lead-free solder are relatively few, primarily due to the lack of available methods for testing. Prior work in literature uses Split Hopkinson Bar (SPHB) experiments for high strain-rate characterization (≥ 300s−1) [1,2], while a modified micro-scale tester is used for medium strain-rate characterization (0.005s−1 to 300s−1) [3] and an impact hammer test setup for testing in a strain-rate regime from 1s−1 to 100s−1 [4]. However, there is still limited data in strain-rate regimes of relevance, specifically for drop shock applications. In this paper, we present orthogonal metal cutting as a novel method to characterize lead-free solder alloys. Experiments are carried out using a wedgelike tool that cuts through a work piece at a fixed depth and rake angle while maintaining a constant cutting velocity. These experiments are conducted at room temperature on Sn1.0Ag0.5Cu bulk test specimens with strain-rates varying from 0.32 to 48s−1. The range of strain-rates is only limited by the ball screw driven slide allowing higher strain-rates if needed. The strains and strain-rates are captured through Particle Image Velocimetry (PIV) using sequential images taken from a high-speed camera just ahead of the cutting tool. The PIV enables non-contact recording of high strain-rate deformations, while the dynamometer on the cutting head allows one to capture the forces exerted during the cutting process. Results for the stress-strain response obtained through the experiments are compared to prior work for validation. Orthogonal metal cutting is shown to be a potentially attractive method for characterization of solder at higher strain-rates.

scholarly journals Effect of Stress-Relieving Heat Treatment on the High Strain Rate Dynamic Compressive Properties of Additively Manufactured Ti6Al4V (ELI)

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 653
Author(s):  
Amos Muiruri ◽  
Maina Maringa ◽  
Willie du Preez ◽  
Leonard Masu
Keyword(s):  
Plastic Strain ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Deformation Behaviour ◽  
Test System ◽  
Strain Rates ◽  
Stress Relieving ◽  
Strain Rate Compression

A study was undertaken on the compressive high strain rate properties and deformation behaviour of Direct Metal Laser-Sintered (DMLS) Ti6Al4V (ELI) parts in two separate forms: as-built (AB) and stress relieved (SR). The high strain rate compression tests were carried out using a Split Hopkinson Pressure Bar test system at ambient temperature. The average plastic strain rates attained by the system were 400 s−1 and 700 s−1. Comparative analyses of the performance (flow stresses and fracture strains) of AB and SR specimens were carried out based on the results obtained at these two plastic strain rates. Microstructural analyses were performed to study the failure mechanisms of the deformed specimens and fracture surfaces. Vickers microhardness test values were obtained before and after high strain rate compression testing. The results obtained in both cases showed the strain rate sensitivity of the stress-relieved samples to be higher in comparison to those of as-built ones, at the same value of true strain.

scholarly journals High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2098 ◽  
Author(s):  
Olga Yakovtseva ◽  
Maria Sitkina ◽  
Ahmed O. Mosleh ◽  
Anastasia Mikhaylovskaya
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Superplastic Deformation ◽  
High Strain ◽  
Flow Behavior ◽  
Constant Strain Rate ◽  
Superplastic Forming ◽  
High Strength ◽  
Strain Rate Range ◽  
Strain Rates

Increasing the strain rate at superplastic forming is a challenging technical and economic task of aluminum forming manufacturing. New aluminum sheets exhibiting high strain rate superplasticity at strain rates above 0.01 s−1 are required. This study describes the microstructure and the superplasticity properties of a new high-strength Al-Zn-Mg-based alloy processed by a simple thermomechanical treatment including hot and cold rolling. The new alloy contains Ni to form Al3Ni coarse particles and minor additions of Zr (0.19 wt.%) and Sc (0.06 wt.%) to form nanoprecipitates of the L12-Al3 (Sc,Zr) phase. The design of chemical and phase compositions of the alloy provides superplasticity with an elongation of 600–800% in a strain rate range of 0.01 to 0.6/s and residual cavitation less than 2%. A mean elongation-to-failure of 400% is observed at an extremely high constant strain rate of 1 s−1. The strain-induced evolution of the grain and dislocation structures as well as the L12 precipitates at superplastic deformation is studied. The dynamic recrystallization at superplastic deformation is confirmed. The superplastic flow behavior of the proposed alloy is modeled via a mathematical Arrhenius-type constitutive model and an artificial neural network model. Both models exhibit good predictability at low and high strain rates of superplastic deformation.

Sign in / Sign up

Export Citation Format

Share Document