scholarly journals Basin-Scale Carbon Monoxide Distributions in the Parallel Ocean Program

2007 ◽  
Vol 11 (22) ◽  
pp. 1-30 ◽  
Author(s):  
Shaoping Chu ◽  
Scott Elliott ◽  
David Erickson
Keyword(s):  
Carbon Monoxide ◽  
Large Scale ◽  
Three Dimensional ◽  
Grazing Pressure ◽  
Dissolved Organics ◽  
Basin Scale ◽  
Processing Modes ◽  
Bacterial Uptake ◽  
Structural Influence ◽  
Parallel Ocean Program

Abstract As a primary photochemical constituent in upper-ocean and tropospheric geocycling, carbon monoxide is of interest to a variety of global change research communities. Dynamic three-dimensional simulations of its marine concentration patterns, emphasizing Pacific surface waters, are presented. Calculations were driven by nitrogen/iron ecodynamics within the Parallel Ocean Program (POP) transport framework. Photoproduction was estimated following broadband transfer of ultraviolet A radiation down to and penetrating the mixed layer. Quantum efficiency, absorption, the chromophoric fraction of dissolved organics, and related microchemical parameters were all varied, in some cases collectively. Bacterial uptake was parameterized through stages of refinement ranging from a single global average time constant to the application of steady-state zooplanktonic grazing pressure. Major features of basin-spanning ship track data can be reproduced including tropical to gyre and temperate frontal ratios. Evidence for ecosystem structural influence upon the removal kinetics is reviewed and investigated. Polar waters exhibit unique processing modes and the periphery of the ocean requires specialized handling of organic and bacterial behavior. Large-scale budgets are consistent with recent independent determinations both with respect to internal turnover and flux to the atmosphere. A parsimonious mechanism involving optimized yield is recommended for early system model efforts. Areas awaiting improvement include resolution of UV and the segregation of both light-interacting carbon compounds and microbial populations as tracers.

scholarly journals Carbon monoxide and related trace gases and aerosols over the Amazon Basin during the wet and dry seasons

2012 ◽  
Vol 12 (13) ◽  
pp. 6041-6065 ◽  
Author(s):  
M. O. Andreae ◽  
P. Artaxo ◽  
V. Beck ◽  
M. Bela ◽  
S. Freitas ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Southern Hemisphere ◽  
Biomass Burning ◽  
Large Scale ◽  
Amazon Basin ◽  
Photochemical Degradation ◽  
Wet Season ◽  
Biomass Smoke ◽  
Airborne Measurements ◽  
Basin Scale

Abstract. We present the results of airborne measurements of carbon monoxide (CO) and aerosol particle number concentration (CN) made during the Balanço Atmosférico Regional de Carbono na Amazônia (BARCA) program. The primary goal of BARCA is to address the question of basin-scale sources and sinks of CO2 and other atmospheric carbon species, a central issue of the Large-scale Biosphere-Atmosphere (LBA) program. The experiment consisted of two aircraft campaigns during November–December 2008 (BARCA-A) and May–June 2009 (BARCA-B), which covered the altitude range from the surface up to about 4500 m, and spanned most of the Amazon Basin. Based on meteorological analysis and measurements of the tracer, SF6, we found that airmasses over the Amazon Basin during the late dry season (BARCA-A, November 2008) originated predominantly from the Southern Hemisphere, while during the late wet season (BARCA-B, May 2009) low-level airmasses were dominated by northern-hemispheric inflow and mid-tropospheric airmasses were of mixed origin. In BARCA-A we found strong influence of biomass burning emissions on the composition of the atmosphere over much of the Amazon Basin, with CO enhancements up to 300 ppb and CN concentrations approaching 10 000 cm−3; the highest values were in the southern part of the Basin at altitudes of 1–3 km. The ΔCN/ΔCO ratios were diagnostic for biomass burning emissions, and were lower in aged than in fresh smoke. Fresh emissions indicated CO/CO2 and CN/CO emission ratios in good agreement with previous work, but our results also highlight the need to consider the residual smoldering combustion that takes place after the active flaming phase of deforestation fires. During the late wet season, in contrast, there was little evidence for a significant presence of biomass smoke. Low CN concentrations (300–500 cm−3) prevailed basinwide, and CO mixing ratios were enhanced by only ~10 ppb above the mixing line between Northern and Southern Hemisphere air. There was no detectable trend in CO with distance from the coast, but there was a small enhancement of CO in the boundary layer suggesting diffuse biogenic sources from photochemical degradation of biogenic volatile organic compounds or direct biological emission. Simulations of CO distributions during BARCA-A using a range of models yielded general agreement in spatial distribution and confirm the important contribution from biomass burning emissions, but the models evidence some systematic quantitative differences compared to observed CO concentrations. These mismatches appear to be related to problems with the accuracy of the global background fields, the role of vertical transport and biomass smoke injection height, the choice of model resolution, and reliability and temporal resolution of the emissions data base.

scholarly journals Double-Diffusive Recipes. Part I: Large-Scale Dynamics of Thermohaline Staircases

2014 ◽  
Vol 44 (5) ◽  
pp. 1269-1284 ◽  
Author(s):  
T. Radko ◽  
A. Bulters ◽  
J. D. Flanagan ◽  
J.-M. Campin
Keyword(s):  
Numerical Simulations ◽  
Large Scale ◽  
Density Ratio ◽  
Three Dimensional ◽  
Flux Ratio ◽  
Double Diffusion ◽  
Spontaneous Generation ◽  
Computational Domain ◽  
The North ◽  
Basin Scale

Abstract Three-dimensional dynamics of thermohaline staircases are investigated using a series of basin-scale staircase-resolving numerical simulations. The computational domain and forcing fields are chosen to reflect the size and structure of the North Atlantic subtropical thermocline. Salt-finger transport is parameterized using the flux-gradient formulation based on a suite of recent direct numerical simulations. Analysis of the spontaneous generation of thermohaline staircases suggests that thermohaline layering is a product of the gamma instability, associated with the variation of the flux ratio with the density ratio . After their formation, numerical staircases undergo a series of merging events, which systematically increase the size of layers. Ultimately, the system evolves into a steady equilibrium state with pronounced layers 20–50 m thick. The size of the region occupied by thermohaline staircases is controlled by the competition between turbulent mixing and double diffusion. Assuming, in accordance with observations, that staircases form when the density ratio is less than the critical value of , the authors arrive at an indirect estimate of the characteristic turbulent diffusivity in the subtropical thermocline.

scholarly journals Carbon monoxide and related trace gases and aerosols over the Amazon Basin during the wet and dry seasons

2012 ◽  
Vol 12 (3) ◽  
pp. 8107-8168 ◽  
Author(s):  
M. O. Andreae ◽  
P. Artaxo ◽  
V. Beck ◽  
M. Bela ◽  
S. Freitas ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Southern Hemisphere ◽  
Biomass Burning ◽  
Large Scale ◽  
Amazon Basin ◽  
Photochemical Degradation ◽  
Wet Season ◽  
Biomass Smoke ◽  
Airborne Measurements ◽  
Basin Scale

Abstract. We present the results of airborne measurements of carbon monoxide (CO) and aerosol particle number concentration (CN) made during the Balanço Atmosférico Regional de Carbono na Amazônia (BARCA) program. The primary goal of BARCA is to address the question of basin-scale sources and sinks of CO2 and other atmospheric carbon species, a central issue of the Large-scale Biosphere-Atmosphere (LBA) program. The experiment consisted of two aircraft campaigns during November–December 2008 (BARCA-A) and May 2009 (BARCA-B), which covered the altitude range from the surface up to about 4500 m, and spanned most of the Amazon Basin. Based on meteorological analysis and measurements of the tracer, SF6, we found that airmasses over the Amazon Basin during the late dry season (BARCA-A, November 2008) originated predominantly from the Southern Hemisphere, while during the late wet season (BARCA-B, May 2009) low-level airmasses were dominated by northern-hemispheric inflow, and mid-tropospheric airmasses were of mixed origin. In BARCA-A we found strong influence of biomass burning emissions on the composition of the atmosphere over much of the Amazon Basin, with CO enhancements up to 300 ppb and CN concentrations approaching 10 000 cm−3; the highest values were in the southern part of the Basin at altitudes of 1–3 km. The ΔCN/ΔCO ratios were diagnostic for biomass burning emissions, and were lower in aged than in fresh smoke. Fresh emissions indicated CO/CO2 and CN/CO emission ratios in good agreement with previous work, but our results also highlight the need to consider the residual smoldering combustion that takes place after the active flaming phase of deforestation fires. During the late wet season, in contrast, there was little evidence for a significant presence of biomass smoke. Low CN concentrations (300–500 cm−3) prevailed basinwide, and CO mixing ratios were enhanced by only ~10 ppb above the mixing line between Northern and Southern Hemisphere air. There was no detectable trend in CO with distance from the coast, but there was a small enhancement of CO in the boundary layer suggesting diffuse biogenic sources from photochemical degradation of biogenic volatile organic compounds or direct biological emission. Simulations of CO distributions during BARCA-A using a range of models yielded general agreement in spatial distribution and confirm the important contribution from biomass burning emissions, but the models evidence some systematic quantitative differences compared to observed CO concentrations. These mismatches appear to be related to problems with the accuracy of the global background fields, the role of vertical transport and biomass smoke injection height, the choice of model resolution, and reliability and temporal resolution of the emissions data base.

scholarly journals A Review on Additive Manufacturing Possibilities for Electrical Machines

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1940
Author(s):  
Muhammad Usman Naseer ◽  
Ants Kallaste ◽  
Bilal Asad ◽  
Toomas Vaimann ◽  
Anton Rassõlkin
Keyword(s):  
Additive Manufacturing ◽  
Large Scale ◽  
Three Dimensional ◽  
Electrical Machines ◽  
Electromagnetic Properties ◽  
Scale Production ◽  
Performance Parameters ◽  
Large Scale Production ◽  
One Step ◽  
Manufacturing Techniques

This paper presents current research trends and prospects of utilizing additive manufacturing (AM) techniques to manufacture electrical machines. Modern-day machine applications require extraordinary performance parameters such as high power-density, integrated functionalities, improved thermal, mechanical & electromagnetic properties. AM offers a higher degree of design flexibility to achieve these performance parameters, which is impossible to realize through conventional manufacturing techniques. AM has a lot to offer in every aspect of machine fabrication, such that from size/weight reduction to the realization of complex geometric designs. However, some practical limitations of existing AM techniques restrict their utilization in large scale production industry. The introduction of three-dimensional asymmetry in machine design is an aspect that can be exploited most with the prevalent level of research in AM. In order to take one step further towards the enablement of large-scale production of AM-built electrical machines, this paper also discusses some machine types which can best utilize existing developments in the field of AM.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

scholarly journals Shell-crossing in a ΛCDM Universe

2020 ◽  
Vol 501 (1) ◽  
pp. L71-L75
Author(s):  
Cornelius Rampf ◽  
Oliver Hahn
Keyword(s):  
Dark Matter ◽  
Perturbation Theory ◽  
Large Scale ◽  
Cold Dark Matter ◽  
Three Dimensional ◽  
Random Initial Data ◽  
Recursion Relations ◽  
Indispensable Tool ◽  
First Time ◽  
Very High

ABSTRACT Perturbation theory is an indispensable tool for studying the cosmic large-scale structure, and establishing its limits is therefore of utmost importance. One crucial limitation of perturbation theory is shell-crossing, which is the instance when cold-dark-matter trajectories intersect for the first time. We investigate Lagrangian perturbation theory (LPT) at very high orders in the vicinity of the first shell-crossing for random initial data in a realistic three-dimensional Universe. For this, we have numerically implemented the all-order recursion relations for the matter trajectories, from which the convergence of the LPT series at shell-crossing is established. Convergence studies performed at large orders reveal the nature of the convergence-limiting singularities. These singularities are not the well-known density singularities at shell-crossing but occur at later times when LPT already ceased to provide physically meaningful results.

scholarly journals Advancing Drug Discovery for Neurological Disorders Using iPSC-Derived Neural Organoids

2021 ◽  
Vol 22 (5) ◽  
pp. 2659
Author(s):  
Gianluca Costamagna ◽  
Giacomo Pietro Comi ◽  
Stefania Corti
Keyword(s):  
Drug Discovery ◽  
Drug Screening ◽  
Neural Development ◽  
Neurological Disorders ◽  
Large Scale ◽  
Three Dimensional ◽  
Induced Pluripotent Stem Cell ◽  
Cellular Level ◽  
Complex Data ◽  
Complex Data Sets

In the last decade, different research groups in the academic setting have developed induced pluripotent stem cell-based protocols to generate three-dimensional, multicellular, neural organoids. Their use to model brain biology, early neural development, and human diseases has provided new insights into the pathophysiology of neuropsychiatric and neurological disorders, including microcephaly, autism, Parkinson’s disease, and Alzheimer’s disease. However, the adoption of organoid technology for large-scale drug screening in the industry has been hampered by challenges with reproducibility, scalability, and translatability to human disease. Potential technical solutions to expand their use in drug discovery pipelines include Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) to create isogenic models, single-cell RNA sequencing to characterize the model at a cellular level, and machine learning to analyze complex data sets. In addition, high-content imaging, automated liquid handling, and standardized assays represent other valuable tools toward this goal. Though several open issues still hamper the full implementation of the organoid technology outside academia, rapid progress in this field will help to prompt its translation toward large-scale drug screening for neurological disorders.

Sign in / Sign up

Export Citation Format

Share Document