The tensile properties of weft-knitted biaxial tubular fabrics and reinforced composites

2021 ◽  
pp. 004051752110648
Author(s):  
Mengmeng Zhou ◽  
Gaoming Jiang ◽  
Zhe Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Properties ◽  
Deformation Behavior ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Reinforced Composites ◽  
Fiber Volume ◽  
Second Stage ◽  
Infusion Technique

Weft-knitted biaxial tubular (WKBT) fabrics have been infiltrated via a resin film infusion technique to fabricate reinforced composites. To understand the mechanical properties of WKBT fabrics and the reinforced composites, the strength efficiency of insertion yarns and insertion fiber volume fraction are used to evaluate the tensile strength. The tensile properties of WKBT fabrics and the reinforced composites are studied in the 0° and 90° directions. The results show that both have two failure stages. The first stage is the fracture of insertion yarns which provide the main tensile strength, and the second stage is the fracture of stitch yarns which have significant effect on the tensile strength of WKBT fabrics and the reinforced composites. It is observed that the deformation behavior and failure mechanism of WKBT fabric reinforced composites are closely related to the structure of WKBT fabric, which can be used to predict the failure mode and morphology of WKBT fabric reinforced composites.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

scholarly journals Variation of the Mechanical Properties for Natural Fiber Reinforced Composites with Different Weight Ratio of Ziziphus Nummularia’s (Ber) Fibers

2020 ◽  
Vol 8 (6) ◽  
pp. 5393-5397
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Young Modulus ◽  
Fiber Volume

In the present era, Natural fibers are favored for the formation of composites due to their low density, high strength, biodegradability, easy production, low carbon foot, environment friendly nature in comparison of synthetic fibers. This Paper deals with NFRC made from natural fibers obtained from the plants of arid region of Western Rajasthan on which a few researchers are focusing. This paper discuss on the extraction process of fiber from the ber’s stems, manufacturing of composites by using epoxy resin & ber’s fibers then testing of its mechanical properties e.g. tensile strength, young modulus, yield strength , and percentage elongation. Six Sample were made having weight ratio - 0.1, 0.2, 0.3, 0.4, 0.45, & 0. 6. Dog bone samples were prepared according to the ASTM D638 (Type IV) standard. Tensile strength varies from 12.19 MPa to 25 MPa, while young modulus varies from 1.4GPa to 2.9GPa for different weight ratios. Yield strength varies from 10.77 MPa to 21.16 MPa. Percentage of Elongation varies from 1 to 3%. These results shows that ber’s stems can be used for fiber extraction to manufacture composites materials & for better mechanical properties minimum fiber volume fraction percentage is 13% and maximum fiber fraction is 31%.This data can be used further when optimum value of fiber volume fraction is required to form composites from ber’s fibers.

Mechanical Properties of Interface Layers in SiC/TiAl Composite

2021 ◽  
Vol 1016 ◽  
pp. 151-155
Author(s):  
Keizo Hashimoto ◽  
Jiang Jin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Volume ◽  
Sic Fiber ◽  
Pull Out ◽  
Interface Layers ◽  
Properties Of Composites

Although metal matrix composites (MMC) for the high temperature structural material have been investigated extensively for many years, applications of MMC have been still limited. Among many combinations between the ceramic fibers and the matrix materials, combination of SiC fiber and TiAl based intermetallic compounds has been expected to be one of the best combination, since both SiC fiber and TiAl have demonstrated the capabilities of the low density heat resistant materials. SiC fiber reinforced TiAl composites have been successfully fabricated using hot press method. Optimum temperature and pressure have been determined. SiC/TiAl composite having relatively low fiber volume fraction shows nearly an ideal elastic property applying the law of mixture. Effects of interface layers on the mechanical properties of composites have been studied in detail. Micro-indentation on a single fiber was carried out to examine the pull out strength of SiC fiber quantitatively. Estimated shear stress on the interface was 145-195MPa, those values are quite reasonable since the tensile strength of TiAl matrix was 420MPa and the maximum shear stress would be the half of tensile strength according to Schmid law. Three-point bending tests have been carried out to evaluate the mechanical properties of composites. Fiber volume fraction 8.9% specimen shows ideal bending stiffness compare with the calculated values based on the low of mixture. Reaction layers and the interface between SiC fiber and TiAl have been analyzed by SEM-EDS and XRD. At least two or more reaction layers have been identified. These reaction layers can be explained based on the Si-Ti-C ternary equilibrium phase diagram at 1373K. Optimum conditions of interface structure will be discussed

scholarly journals KARAKTERISTIK SIFAT TARIK DAN MODE PATAHAN KOMPOSIT POLYESTER BERPENGUAT SERAT TAPIS KELAPA

2014 ◽  
Vol 4 (2) ◽  
Author(s):  
I Made Astika ◽  
I Gusti Komang Dwijana
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
High Price ◽  
Fiber Volume ◽  
Production Methods ◽  
Fiber Treatment ◽  
Research Show

The purpose of this study is to investigate the mechanical properties i.e. tensile strength of composites coconut filter fiber. In the future this material can be used to replace the wood, bamboo and gipsun which are high price and lower water resistance.The research material made with coconut filter fiber as reinforcement and matrix resin unsaturated polyester (UPRs) type Yukalac BQTN 157, with 1% hardener types MEKPO (Methyl Ethyl Ketone Peroxide) and fiber treatment by  0.5% KMnO4. Production methods are poltrusion and the variations of fiber volume fraction are 20, 25 and 30% and fiber length are 5, 10 and 15 mm. Testing of mechanical properties is tensile test (ASTM D3039-76) The results of research show  that  the longer of fiber and the bigger of fiber volume fraction, the higher of tensile strength are obtained. The fracture mode are overload, debonding, pullout and crack deflection 

Effect of Polypropylene Fiber on Mechanical Properties of Concrete Containing Fly Ash

2011 ◽  
Vol 346 ◽  
pp. 26-29 ◽  
Author(s):  
Hong Wei Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Modulus Of Elasticity ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Splitting Tensile Strength ◽  
Fiber Volume

A designed experimental study has been conducted to investigate the effect of the fiber fraction of polypropylene fiber on the mechanical properties of concrete containing fly ash, a large number of experiments have been carried out in this study. The mechanical properties include compressive strength, splitting tensile strength and compressive modulus of elasticity. On the basis of the experimental results of the specimens of six sets of mix proportions, the mechanism of action of polypropylene fiber on these mechanical properties has been analyzed in details. The results indicate that there is a tendency of increase in the compressive strength and splitting tensile strength, and the modulus of elasticity of concrete containing fly ash decrease gradually with the increase of fiber volume fraction with appropriate content.

An Experimental Investigation on Suitability of Using Sisal Fibers in Reinforced Concrete Composites

2022 ◽  
Author(s):  
John K. Makunza ◽  
G. Senthil Kumaran
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Fiber Volume ◽  
Sisal Fibers

Fiber reinforcement is widely used in construction engineering to improve the mechanical properties of concrete such as compressive and tensile strengths. Concrete is strong in compression but weak in tension and is a brittle material. In the construction industry, strength, durability and cost are among the major factors for selecting the suitable construction materials. During this investigation, the mechanical properties of sisal fibers reinforced concrete (SFRC) were assessed namely, flexural strength, tensile strength ad interfacial bond strength. The said properties were assessed in two types of reinforcement namely, randomly oriented sisal fibers and parallel oriented sisal fibers reinforcement. In both cases the sisal fibers were varied in volume fractions so as to establish the optimum value. The mechanical properties of flexural and tensile strengths were found to increase considerably with increasing fiber volume fractions until an optimum volume fraction is reached, thereafter, the strengths were found to decrease continuously. The prominent increment of 32.4% in flexural strength at fiber volume fraction of 2.0% parallel reinforced fiber concrete composite was observed. There was very small increment on both flexural and tensile strength for randomly oriented chopped sisal fibers reinforced concrete (SFRC). The Interfacial bond strength was found to be 0.12 N/mm2 and was observed to be prominent for chopped sisal fibers reinforced concrete specimens tested for flexural strength. During failure, fiber pull-out was observed and the composite was observed to behave in a ductile manner whereby the fibers were able to carry more load while full fracture had occurred on the specimen. The water absorption capacity of the SFRC was found to increase with increasing sisal fiber volume fraction.

Monitoring of mechanical properties of prestressed glass fiber epoxy composites over 12 months after fabrication

2021 ◽  
pp. 002199832110047
Author(s):  
Mahmoud Mohamed ◽  
Siddhartha Brahma ◽  
Haibin Ning ◽  
Selvum Pillay
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Flexural Strength ◽  
Compressive Residual Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Initial Increase ◽  
Fiber Volume

Fiber prestressing during matrix curing can significantly improve the mechanical properties of fiber-reinforced polymer composites. One primary reason behind this improvement is the generated compressive residual stress within the cured matrix, which impedes cracks initiation and propagation. However, the prestressing force might diminish progressively with time due to the creep of the compressed matrix and the relaxation of the tensioned fiber. As a result, the initial compressive residual stress and the acquired improvement in mechanical properties are prone to decline over time. Therefore, it is necessary to evaluate the mechanical properties of the prestressed composites as time proceeds. This study monitors the change in the tensile and flexural properties of unidirectional prestressed glass fiber reinforced epoxy composites over a period of 12 months after manufacturing. The composites were prepared using three different fiber volume fractions 25%, 30%, and 40%. The results of mechanical testing showed that the prestressed composites acquired an initial increase up to 29% in the tensile properties and up to 32% in the flexural properties compared to the non-prestressed counterparts. Throughout the 12 months of study, the initial increase in both tensile and flexural strength showed a progressive reduction. The loss ratio of the initial increase was observed to be inversely proportional to the fiber volume fraction. For the prestressed composites fabricated with 25%, 30%, and 40% fiber volume fraction, the initial increase in tensile and flexural strength dropped by 29%, 25%, and 17%, respectively and by 34%, 26%, and 21%, respectively at the end of the study. Approximately 50% of the total loss took place over the first month after the manufacture, while after the sixth month, the reduction in mechanical properties became insignificant. Tensile modulus started to show a very slight reduction after the fourth/sixth month, while the flexural modulus reduction was observed from the beginning. Although the prestressed composites displayed time-dependent losses, their long-term mechanical properties still outperformed the non-prestressed counterparts.

scholarly journals Effect of Zr Addition on the Mechanical Properties and Superplasticity of a Forged SP700 Titanium Alloy

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 906
Author(s):  
Dong Han ◽  
Yongqing Zhao ◽  
Weidong Zeng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Titanium Alloy ◽  
Tensile Properties ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Tensile Elongation ◽  
Β Phase ◽  
Zr Addition ◽  
Fine Microstructure

The present study focuses on the effect of 1% Zr addition on the microstructure, tensile properties and superplasticity of a forged SP700 alloy. The results demonstrated that Zr has a significant effect on inhibiting the microstructural segregation and increasing the volume fraction of β-phase in the forged SP700 alloy. After annealing at 820 °C for 1 h and aging at 500 °C for 6 h, the SP700 alloy with 1% Zr showed a completely globular and fine microstructure. The yield strength, ultimate tensile strength and tensile elongation of the alloy with optimized microstructure were 1185 MPa, 1296 MPa and 10%, respectively. The superplastic deformation was performed at 750 °C with an elongation of 1248%. The improvement of tensile properties and superplasticity of the forged SP700 alloy by Zr addition was mainly attributed to the uniform and fine globular microstructures.

Effects of Fiber Volume Fraction on Mechanical Properties of SiC-Fiber/Si3N4-Matrix Composites

1994 ◽  
Vol 77 (7) ◽  
pp. 1897-1900 ◽  
Author(s):  
Hockin H. K. Xu ◽  
Claudia P. Ostertag ◽  
Linda M. Braun ◽  
Isabel K. Lloyd
Keyword(s):  
Mechanical Properties ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Matrix Composites ◽  
Fiber Volume ◽  
Sic Fiber ◽  
Si3n4 Matrix

scholarly journals Tensile Mechanical Properties and Failure Modes of a Basalt Fiber/Epoxy Resin Composite Material

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Jingjing He ◽  
Junping Shi ◽  
Xiaoshan Cao ◽  
Yifeng Hu
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Fiber Volume Fraction ◽  
Failure Modes ◽  
Volume Fraction ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Fiber Volume ◽  
Fiber Clustering ◽  
Fiber Orientation Angle

Uniaxial tensile tests of basalt fiber/epoxy (BF/EP) composite material with four different fiber orientations were conducted under four different fiber volume fractions, and the variations of BF/EP composite material failure modes and tensile mechanical properties were analyzed. The results show that when the fiber volume fraction is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all decrease with increasing fiber orientation angle. When the fiber orientation angle is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all increase with increasing fiber volume fraction. A certain degree of fiber clustering appears in the epoxy resin when the basalt fiber volume fraction is >1.2%. The fiber equidistribution coefficient and clustering fiber content were used to characterize the basalt fiber clustering effect. With the increase of fiber volume fraction, the clustering fiber content gradually increased, but the fiber equidistribution coefficient decreased. Meanwhile, based on Tsai theory, a geometric model and a tensile mechanical model of the clustering fiber are established. By considering the fiber clustering effect, the BF/EP composite material tensile strength is calculated, and the calculated values are close to the experimental results.

Sign in / Sign up

Export Citation Format

Share Document