Investigation of the effects of welding variables on the welding defects of the friction stir welded high density polyethylene sheets

2021 ◽  
pp. 009524432110588
Author(s):  
Mustafa Kemal Bilici
Keyword(s):  
Friction Stir Welding ◽  
High Density Polyethylene ◽  
Welding Process ◽  
High Strength ◽  
High Density ◽  
Welding Parameters ◽  
Friction Stir ◽  
Wide Range ◽  
Welding Defects ◽  
Welding Processes

Modern thermoplastic materials are used in an expanding range of engineering applications, such as in the automotive industry, due to their enhanced stress-to-weight ratios, toughness, a very short time of solidification, and a low thermal conductivity. Recently, friction stir welding has started to be used in joining processes in these areas. There are many factors that affect weld performance and weld quality in friction stir welding (FSW). These factors must be compatible with each other. Due to the large number of welding variables in friction stir welding processes, it is very difficult to achieve high strength FSW joints, high welding performance, and control the welding process. Welding variables that form the basis of friction stir welding; machine parameters, tool variables, and material properties are divided into three main groups. Each welding variable has different effects on the weld joint. In this study, friction stir welds were made on high density polyethylene (HDPE) sheets with factors selected from machine parameters and welding tool variables. Although the welding performance, quality, and strength gave good results in some conditions, successful joints could not be realized in some conditions. In particular, welding defects occurring in the combination of HDPE material with FSW were investigated. Welding quality, defects, and performances were examined with macrostructure. In addition, the tensile strength values of some the joints were determined. The main purpose of this study is to determine the welding defects that occur at the joints. The causes of welding defects, prevention methods, and which weld variables caused were investigated. Welding parameters and welding defects caused by welding tools were examined in detail. In addition, the factors causing welding defects were changed in a wide range and the changes in the defects were observed.

A Study of Friction Stir Welding of High Density Polyethylene

2018 ◽  
Author(s):  
Jamal Sheikh-Ahmad ◽  
Dima Ali ◽  
Firas Jarrar ◽  
Suleyman Deveci
Keyword(s):  
Friction Stir Welding ◽  
High Density Polyethylene ◽  
Elevated Temperatures ◽  
Welding Process ◽  
High Density ◽  
Weld Quality ◽  
Welding Zone ◽  
Friction Stir ◽  
Welding Processes ◽  
Material Temperature

Friction stir welding of high density polyethylene sheets was performed at different rotational and welding speeds and the material temperature close to the welding zone was monitored by infrared thermography and thermocouple measurements. Welding quality was evaluated by macrostructure analysis and tensile testing. Fracture surfaces of the tensile specimens were also analyzed. It was found that weld quality is highly dependent on the temperature of the material in the welding zone. For some specific welding conditions the welding process was unstable due to elevated temperatures reaching the melting point of HDPE. Instability of the welding processes was characterized by cyclic material temperatures and down forces. Decreasing the welding speed and increasing the rotational speed was found to improve weld quality.

Influence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li Alloy

2016 ◽  
Vol 857 ◽  
pp. 228-231
Author(s):  
Ho Sung Lee ◽  
Ye Rim Lee ◽  
Kyung Ju Min
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Space Shuttle ◽  
Welding Process ◽  
High Strength ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Friction Stir ◽  
Mechanical And Microstructural Properties ◽  
Tool Rotation

Aluminum-Lithium alloys have been found to exhibit superior mechanical properties as compared to the conventional aerospace aluminum alloys in terms of high strength, high modulus, low density, good corrosion resistance and fracture toughness at cryogenic temperatures. Even though they do not form low-melting eutectics during fusion welding, there are still problems like porosity, solidification cracking, and loss of lithium. This is why solid state friction stir welding is important in this alloy. It is known that using Al-Cu-Li alloy and friction stir welding to super lightweight external tank for space shuttle, significant weight reduction has been achieved. The objective of this paper is to investigate the effect of friction stir tool rotation speed on mechanical and microstructural properties of Al-Cu-Li alloy. The plates were joined with friction stir welding process using different tool rotation speeds (300-800 rpm) and welding speeds (120-420 mm/min), which are the two prime welding parameters in this process.

scholarly journals Parametric Study Of Friction Stir Spot Welding (FSSW) For Polymer Materials Case Of High Density Polyethylene Sheets: Experimental And Numerical Study

2020 ◽  
Vol 15 (55) ◽  
Author(s):  
Djilali Benyerou ◽  
El Bahri Ould Chikh ◽  
Habib Khellafi ◽  
Hadj Miloud Meddah ◽  
Ali Benhamena ◽  
...  
Keyword(s):  
Finite Element ◽  
Numerical Modeling ◽  
High Density Polyethylene ◽  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
High Density ◽  
Polymer Materials ◽  
Friction Stir ◽  
Welding Processes

Friction stir spot welding (FSSW) is a very important part of conventional friction stir welding (FSW) which can be a replacement for riveted assemblies and resistance spot welding. This technique provides high quality joints compared to conventional welding processes. Friction stir spot welding (FSSW) is a new technology adopted to join various types of metals such as titanium, aluminum, magnesium. It is also used for welding polymer materials which are difficult to weld by the conventional welding process. In various industrial applications, high density polyethylene (HDPE) becomes the most used material. The parameters and mechanical properties of the welds are the major problems in the welding processes. In this paper, we have presented a contribution in finite element modeling of the friction stir spot welding process (FSSW) using Abaqus as a finite element solver. The objective of this paper is to study the HDPE plates resistance of stir spot welding joints (FSSW). First, we show the experimental tests results of high-density polyethylene (HDPE) plates assembled by friction stir spot welding (FSSW). Three-dimensional numerical modeling by the finite element method makes it possible to determine the best representation of the weld joint for a good prediction of its behavior. Comparison of the results shows that there is a good agreement between the numerical modeling predictions and the experimental results.

Influence of Friction Stir Welding Parameters on the Mechanical Properties of EN AW-7075 Weld Joints

2016 ◽  
Vol 835 ◽  
pp. 210-215
Author(s):  
Máté Nagy ◽  
Mária Behúlová
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Ultimate Strength ◽  
Base Material ◽  
High Strength ◽  
Welding Parameters ◽  
Micro Hardness ◽  
Friction Stir ◽  
Weld Joints ◽  
Welding Processes

The paper deals with the friction stir welding (FSW) of the high strength EN AW 7075-T651 aluminium alloy with the aim to analyze the influence of welding parameters on the mechanical properties of Al-weld joints. FSW represents relatively novel solid-state technology of material joining which can be successfully applied for welding of several metallic alloys including the high-strength aluminium alloys that are hard to weld by conventional fusion welding processes. In cooperation with VÚZ - PI SR Bratislava, nine experimental weld joints of samples with dimensions of 300 × 150 × 10 mm were prepared using the welding machine of the FSW-LM-060 type and different parameters of welding – the welding speed from 60 to 120 mm/min and the tool rotation rate from 600 to 1000 rpm in clockwise direction. The quality of weld joints was evaluated by static tensile tests and micro-hardness measurements. According to obtained results of tensile testing, the average values of ultimate strength of weld joints are by 32.2 % lower comparing with the ultimate strength of the base material. On the other hand, the ductility increased by 7.2 %. The highest micro-hardness of weld joints at the level of 129 HV was measured in thermo-mechanically affected zone on the retreating side.

Analysis of the Temperature Distribution in Friction Stir Welding Using the Finite Element Method

2013 ◽  
Vol 758 ◽  
pp. 11-19 ◽  
Author(s):  
Mauricio Rangel Pacheco ◽  
Pedro Manuel Calas Lopes Pacheco
Keyword(s):  
Finite Element ◽  
Friction Stir Welding ◽  
Temperature Distribution ◽  
Plastic Strain ◽  
Heat Source ◽  
Translational Motion ◽  
Welding Process ◽  
Welding Parameters ◽  
Friction Stir ◽  
Welding Processes

Welding is a fabrication process widely used in several industrial areas. The welding of metallic alloys presents some basic characteristics as the presence of a localized intensive heat input that promotes mechanical and metallurgical changes. Different from conventional welding processes, where macroscopic fusion is observed, friction welding is a solid state welding process where the joint is produced by the relative rotational and/or translational motion of two pieces under the action of compressive forces producing heat and plastic strain on the friction surfaces. Friction Stir Welding (FSW) process has received much attention for its special characteristics, like the high quality of the joints. Although there are several experimental works on the subject, numerical modeling is not well stated, as the process is very complex involving the coupling of several non-linear phenomena. In this contribution a tridimensional finite element model is presented to study the temperature distribution in plates welded by the FSW process. A weld heat source is proposed to represent the heat generated during the process. The heat source model considers several contributions present in the process as the friction between the tool and the piece and the plastic power associated to the plastic strain developed. Numerical results show that the model is in close agreement with experimental results, indicating that the model is capable of capturing the main characteristics of the process. The proposed model can be used to predict important process characteristics, like the TAZ (Thermal Affected Zone), as a function of the welding parameters.

scholarly journals Comprehensive Analysis of the Microstructure and Mechanical Properties of Friction-Stir-Welded Low-Carbon High-Strength Steels with Tensile Strengths Ranging from 590 MPa to 1.5 GPa

2021 ◽  
Vol 11 (12) ◽  
pp. 5728
Author(s):  
HyeonJeong You ◽  
Minjung Kang ◽  
Sung Yi ◽  
Soongkeun Hyun ◽  
Cheolhee Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Joint Strength ◽  
Solid Phase ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Low Carbon ◽  
Friction Stir ◽  
Welding Processes

High-strength steels are being increasingly employed in the automotive industry, requiring efficient welding processes. This study analyzed the materials and mechanical properties of high-strength automotive steels with strengths ranging from 590 MPa to 1500 MPa, subjected to friction stir welding (FSW), which is a solid-phase welding process. The high-strength steels were hardened by a high fraction of martensite, and the welds were composed of a recrystallized zone (RZ), a partially recrystallized zone (PRZ), a tempered zone (TZ), and an unaffected base metal (BM). The RZ exhibited a higher hardness than the BM and was fully martensitic when the BM strength was 980 MPa or higher. When the BM strength was 780 MPa or higher, the PRZ and TZ softened owing to tempered martensitic formation and were the fracture locations in the tensile test, whereas BM fracture occurred in the tensile test of the 590 MPa steel weld. The joint strength, determined by the hardness and width of the softened zone, increased and then saturated with an increase in the BM strength. From the results, we can conclude that the thermal history and size of the PRZ and TZ should be controlled to enhance the joint strength of automotive steels.

Study of the Key Issues of Friction Stir Welding of Titanium Alloy

2010 ◽  
Vol 638-642 ◽  
pp. 1185-1190 ◽  
Author(s):  
Hui Jie Liu ◽  
Li Zhou ◽  
Yong Xian Huang ◽  
Qi Wei Liu
Keyword(s):  
Titanium Alloy ◽  
Friction Stir Welding ◽  
Melting Point ◽  
Titanium Alloys ◽  
Welding Process ◽  
High Strength ◽  
Liquid Cooling ◽  
Friction Stir ◽  
Key Issues ◽  
Aluminum And Magnesium Alloys

As a new solid-state welding process, friction stir welding (FSW) has been successfully used for joining low melting point materials such as aluminum and magnesium alloys, but the FSW of high melting point materials such as steels and titanium alloys is still difficult to carry out because of their strict requirements for the FSW tool. Especially for the FSW of titanium alloys, some key technological issues need to solve further. In order to accomplish the FSW of titanium alloys, a specially designed tool system was made. The system was composed of W-Re pin tool, liquid cooling holder and shielding gas shroud. Prior to FSW, the Ti-6Al-4V alloy plates were thermo-hydrogen processed to reduce the deformation resistance and tool wear during the FSW. Based on this, the thermo-hydrogen processed Ti-6Al-4V alloy with different hydrogen content was friction stir welded, and the microstructural characterizations and mechanical properties of the joints were studied. Experimental results showed that the designed tool system can fulfill the requirements of the FSW of titanium alloys, and excellent weld formation and high-strength joint have been obtained from the titanium alloy plates.

Sign in / Sign up

Export Citation Format

Share Document