Measurement and analysis for frequency domain error of ultra-precision spindle in a flycutting machine tool

2016 ◽  
Vol 232 (9) ◽  
pp. 1501-1507 ◽  
Author(s):  
Guoda Chen ◽  
Yazhou Sun ◽  
Chenhui An ◽  
Feihu Zhang ◽  
Zhiji Sun ◽  
...  
Keyword(s):  
Machine Tool ◽  
Frequency Domain ◽  
Frequency Domain Analysis ◽  
Frequency Characteristics ◽  
Machining Process ◽  
Machining Accuracy ◽  
Machined Surface ◽  
Ultra Precision ◽  
Machining Process Planning ◽  
Aerostatic Spindle

The ultra-precision spindle is the key component of ultra-precision machine tool, which largely influences the machining accuracy. Its frequency characteristics mainly affect the frequency domain error of the machined surface. In this article, the error measurement setup for the ultra-precision aerostatic spindle in a flycutting machine tool is established. The dynamic and multi-direction errors of the spindle are real-time measured under different rotation speeds. Then, frequency domain analysis is carried out to obtain its regularity characteristics based on the measurement result. Through the analysis, the main synchronous and asynchronous errors with relatively large amplitude of the spindle errors are found, and the amplitude change law of these main spindle errors is obtained. Besides, the cause of the main synchronous and asynchronous errors is also analyzed and indicated. This study deepens the understanding of ultra-precision spindle dynamic characteristics and plays the important role in the spindle frequency domain errors’ control, machining process planning, frequency characteristics analysis and oriented control of the machined surface errors.

scholarly journals A prediction model of the surface topography due to the unbalance of the spindle system in ultra-precision fly-cutting machining

2018 ◽  
Vol 10 (1) ◽  
pp. 168781401774714
Author(s):  
Dongju Chen ◽  
Xianxian Cui ◽  
Ri Pan ◽  
Jinwei Fan ◽  
Chenhui An
Keyword(s):  
Prediction Model ◽  
Surface Topography ◽  
Rotation Speed ◽  
Surface Generation ◽  
Machining Accuracy ◽  
Machined Surface ◽  
Spindle System ◽  
Fly Cutting ◽  
Ultra Precision ◽  
Aerostatic Spindle

In ultra-precision fly-cutting machining, the aerostatic spindle is the key component, which has significant influence on the machined surface quality. The unbalanced spindle directly affects the machining accuracy. In this article, a prediction model of machining surface topography is proposed which involves the effect of the gas film performance of spindle in microscale. With the Weierstrass function, unstable transient response of the aerostatic spindle system is derived by the motion model of the spindle, which response signal represents the surface profile in the ultra-precision machining. Meanwhile, the experiment is performed with different rotation speed of the spindle. And the effect of the unbalanced aerostatic spindle on the surface generation is discussed in time and frequency domain. The conclusion shows that the similar cyclical surface ripple of the workpiece is independent of the spindle speed, and the rotation speed of the spindle and unbalanced spindle directly affects the machining surface topography. This study is quite meaningful for deeply understanding the influence rule of spindle unbalanced error from the viewpoint of machined surface and vibration frequency.

Measurement and Evaluation of Temperature Change of Water Driven Spindle

2016 ◽  
Author(s):  
Akio Hayashi ◽  
Yohichi Nakao
Keyword(s):  
Thermal Stability ◽  
Machine Tool ◽  
Temperature Change ◽  
Thermal Deformation ◽  
Single Point ◽  
Machining Process ◽  
Machining Accuracy ◽  
Precision Machine ◽  
Ultra Precision ◽  
Thermal Stability Of

Recently, various precision products such as lenses or mirrors are produced by the ultra-precision machine tools. Then, the single-point diamond cutting is mainly carried out using the ultra-precision machine tool. In order to generate the high accuracy and high quality machined surfaces, the high stiffness and precise rotational accuracy of the spindle is required for the ultra-precision machining tools. The water driven spindle had been developed for the precision machine tool spindle. This spindle is driven by the generated torque due to the water flow power. Then, the rotational speed can be controlled by the supplied flow rate of water. In addition, the spindle has the water hydrostatic bearings that achieve the high bearing stiffness and precise motion accuracy. Furthermore, it is expected that the water driven spindle has the high thermal stability since the water with low viscosity is used as a coolant media. If the thermal deformation of the spindle is caused during the machining process, the deformation degrades the machining accuracy, accordingly. Thus, it is desirable that the thermal deformation and the temperature change of each part of the spindle and machine tool structure can be controlled and minimized during machining process. In this paper, in order to investigate the thermal stability of the water driven spindle, the measurement tests of the temperature of the water driven spindle were carried out. In addition, the power loss due to the water viscosity between the rotor and the casing of the spindle is calculated. As a result, this paper considers the temperature change and considers the thermal stability of the water driven spindle from the results of experiments.

Dynamic optimization method with applications for machine tools based on approximation model

2017 ◽  
Vol 232 (11) ◽  
pp. 2009-2022 ◽  
Author(s):  
TJ Li ◽  
XH Ding ◽  
K Cheng ◽  
T Wu
Keyword(s):  
Machine Tool ◽  
Performance Optimization ◽  
Machine Tools ◽  
Optimization Design ◽  
Natural Frequencies ◽  
Dynamic Performance ◽  
Machining Process ◽  
Machining Accuracy ◽  
Approximation Model ◽  
Dynamic Behaviors

Natural frequencies and modal shapes of machine tools have position-dependent characteristics owing to their dynamic behaviors changing with the positions of moving parts. It is time-consuming and difficult to evaluate the dynamic behaviors of machine tools and their machining accuracy at different positions. In this paper, a Kriging approximation model coupled with finite element method is proposed to substitute the dynamic equations for obtaining the position-dependent natural frequencies of a machine tool, as well as relative positions between the tool and the workpiece during the machining process. Based on the proposed method, dynamic performance optimization design of the machine tool is conducted under the condition of minimum relative positions. Three case studies are illustrated to demonstrate the implementation of the proposed method.

Research of the Technological Parameters Influencing on the Surface Quality of Micro Complex Surface

2005 ◽  
Vol 291-292 ◽  
pp. 513-518 ◽  
Author(s):  
Ming Jun Chen ◽  
Ying Chun Liang ◽  
Ya Zhou Sun ◽  
W.X. Guo ◽  
Wen Jun Zong
Keyword(s):  
Machine Tool ◽  
Three Dimensional ◽  
Complex Surface ◽  
Cutting Parameters ◽  
Numerical Control ◽  
Tool Geometry ◽  
Machining Accuracy ◽  
Technological Parameters ◽  
Machined Surface ◽  
Machining Errors

In order to machine complex free surface parts, a micro NC (numerical control) three-dimensional machine tool is developed, integrated the PMAC control. Based on this NC machine tool, the influencing of the technological and tool’s parameters on machining accuracy of micro complex surface parts are analyzed, and the cause to lead to the machining errors is explained. Therefore, the cutting parameters and tool geometry parameters to machine micro complex surface, such as the human’s face, can be selected optimally. Finally, the micro complex human’s face is machined on this developed micro machine tool under optimal parameters. The experimental results show that the machined surface is smooth and continuous. The machined quality is satisfied.

To Identify Key Geometric Errors of 3-Axis NC Machine Tool by Machining Accuracy Failure Mode Analysis

2019 ◽  
Author(s):  
Baobao Qi ◽  
Qiang Cheng ◽  
Zhifeng Liu ◽  
Dongyang Sun
Keyword(s):  
Machine Tool ◽  
Failure Mode ◽  
Failure Modes ◽  
Geometric Error ◽  
Mode Analysis ◽  
Major Influence ◽  
Work Piece ◽  
Machining Accuracy ◽  
Geometric Errors ◽  
Machined Surface

Abstract Machine tools usually cut two or more surfaces after the work piece clamped on work table. In order to improve the machining accuracy and optimize accuracy design, it is hoped that the geometric errors that influence the accuracy of machined surface prominently can be known beforehand, so the adjustment will be carried out with a definite objective rather than without any clue. Because the machining accuracy of each direction in 3-D space is different value, in this paper, machining accuracy failure mode was defined as the various combination of the machining accuracy of each direction according to whether it is up to the reserved objective value or not. A three-axis machine tool was selected as an example and there were 7 machining accuracy failure modes for it. Based on the generalized correlation analysis, the correlation relationships between 7 machining accuracy failure modes were analyzed, and the main failure modes that affect the machining accuracy of work piece to be machined were identified. For each machining accuracy failure mode, key geometric error that had major influence on it was identified based on sensitivity analysis. Finally, four stepped work pieces were milled by a 3-axis machine tool to illustrate the analytical method proposed in this study.

Mini Special Issue on Machining Control and Process Monitoring

2014 ◽  
Vol 8 (6) ◽  
pp. 791-791
Author(s):  
Tojiro Aoyama
Keyword(s):  
Machine Tool ◽  
Process Monitoring ◽  
Machine Tools ◽  
Cutting Tools ◽  
Machining Process ◽  
Machining Accuracy ◽  
Special Issue ◽  
Practical Proposal ◽  
Machining Control ◽  
Novel Approaches

Control and process monitoring are key technologies supporting high machining accuracy and efficiency. This special issue features six papers taking novel approaches to controlling machine and cutting tools and monitoring the machining process. The motion control of machine tools and cutting tools are introduced. A new challenge for monitoring the machining process by referring to NC control servo signals implements a practical proposal. The precise identification of friction at driving elements of machine tool components is an important factor in improving machine tool control motion accuracy. I would like to express my sincere appreciation to the authors and reviewers whose invaluable efforts have helped make the publication of this manuscript possible.

Gyroscopic Torque Analysis and Dynamic Balance Test of the Vertical Aerostatic Spindle

2011 ◽  
Vol 697-698 ◽  
pp. 686-691
Author(s):  
Fei Hu Zhang ◽  
Peng Qiang Fu ◽  
C.H. An ◽  
Jiu Wei Sun ◽  
Sheng Fei Wang
Keyword(s):  
Dynamic Characteristics ◽  
Dynamic Pressure ◽  
Dynamic Balance ◽  
Reaction Force ◽  
Rigid Body Dynamics ◽  
Machining Accuracy ◽  
Balance Test ◽  
Close Relationship ◽  
Ultra Precision ◽  
Aerostatic Spindle

Ultra-precision flying cutting machining with a vertical milling style is an important means of ultra-precision machining. It has a close relationship between the machining accuracy and the dynamic characteristics of the aerostatic spindle. The film force acting on the spindle rotor is related to the manufacture, installation and static unbalance or dynamic imbalance or other factors. Therefore, it is necessary to analyze the dynamic pressure force caused by these factors in order to study on the rotor posture and quantitative movement of the spindle. This article derived the solution formula for the dynamic pressure reaction force of the ultra-precision machine tool spindle with vertical static film based on the basic theory of the rigid body dynamics. The gyroscopic torque of the spindle has been analyzed under different conditions with the spindle dynamic balancing tests, which provide a reference to the further analysis of the spindle dynamic characteristics.

Machined NURBS Surface Description Using On-Machine Probing Data

2013 ◽  
Vol 819 ◽  
pp. 33-37 ◽  
Author(s):  
Jin Tao Lai ◽  
Xin Hua Yao ◽  
Wen Li Yu ◽  
Jian Zhong Fu
Keyword(s):  
Machine Tool ◽  
Error Compensation ◽  
Main Idea ◽  
Error Distribution ◽  
Basis Functions ◽  
Machining Accuracy ◽  
Nurbs Surface ◽  
Machined Surface ◽  
Surface Description ◽  
Inspection Data

The error distribution of a machined NURBS surface is complex to describe since the machined surface isnt that easy to obtain. A new method for machined NURBS surface description based on inspection database of on-machine probing is presented. The main idea is to approximate the machined surface using the inspection data and the basis functions of the nominal NURBS surface and to get the error distribution of the surface. A virtual part with a NURBS surface is presented and its error caused by the interaction of the machine-tool-workpiece is obtained using the FEA method at the inspection points. A machined NURBS surface is achieved and the error distribution of the surface is expressed. This method provides a new way in error compensation and it will improve the machining accuracy of a NURBS surface.

Analysis of Reversible Fine Machining Sequence Effect on Surface Integrity

2006 ◽  
Vol 315-316 ◽  
pp. 391-395
Author(s):  
Wen Ge Wu ◽  
Si Qin Pang ◽  
Zhan Qiang Liu
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Surface Integrity ◽  
Machining Process ◽  
Processing Route ◽  
Machining Accuracy ◽  
Machining Efficiency ◽  
Micro Hardness ◽  
Rough Machining ◽  
Machined Surface

Reversible cutting method is a new research thesis proposed to shorten processing route, decrease tool number and handling time, increase machining efficiency. The aim of the presented work was to analysis the effects of reversible fine machining sequence on surface integrity in machined layer. Nonlinear hardening during reverse loading and the change of the Bauschinger effect factor with plastic strain were properly taken into account. In experiments, the residual stresses have been measured using the X-ray diffraction technique (at the surface of the workpiece and in depth). Moreover, micro-hardness and surface roughness of machined surface are presented. Experimental data for the range of cutting parameters tested showed that the reversible fine machining produce the tensile residual stresses at the surface, which are critical in the performance of the machined components. The experimental results of micro-hardness of reversible fine machining technique are smaller than that of general fine machining show that decreased plastic deformation of the surface layer and work-hardening. Surface roughness of machined surface with reversible finishing is discussed. Research results indicted that it can be adopted such planning which rough machining during advance stroke and fine machining or semi-finishing during return stroke in machining process. In this way, it has such advantages that increase machining efficiency and machining accuracy, decrease bending deformation.

Multi-scale prediction of the geometrical deviations of the surface finished by five-axis ball-end milling

2015 ◽  
Vol 231 (10) ◽  
pp. 1685-1702 ◽  
Author(s):  
Bo Li ◽  
Yanlong Cao ◽  
Xuefeng Ye ◽  
Jiayan Guan ◽  
Jiangxin Yang
Keyword(s):  
Machine Tool ◽  
End Milling ◽  
Dynamic Properties ◽  
Machining Process ◽  
Machined Surface ◽  
Multi Scale ◽  
Geometrical Errors ◽  
Macro Scale ◽  
Five Axis

Surface quality and accuracy are the main factors which affect the performance and life cycle of the products. Due to the complexity of the machining process, it is difficult to evaluate the machined surface real time. Simulation of the machining process became the main method to predict and control the quality of the machined surface. This article developed a multi-scale simulation system to predict the overall geometrical features of the milled surface. The effects of locating errors, geometrical errors of the machine tool and tool deflections on the quality of the machined surface are included in the proposed model. Also, different strategies are employed to evaluate the macro-scale and micro-scale geometrical deviations of the machined surface to balance the time cost and accuracy. In comparison with the traditional method, both the form deviations and roughness feature of the machined surface can be predicted. Since the static and dynamic properties of the machining system were considered, both the stable and unstable cutting conditions can be analyzed by using the proposed method. At the end of this article, case studies are carried out to validate the proposed method. The effects of the locating errors, geometrical errors of the machine tool and cutting parameters on the quality of the machined surface are analyzed. The significance of their influences on the quality of the machined surface was investigated.

Sign in / Sign up

Export Citation Format

Share Document