Effect of compression ratio variation and waste cooking oil methyl ester on the combustion and emission characteristics of an engine

2019 ◽  
Vol 31 (7) ◽  
pp. 1257-1280 ◽  
Author(s):  
Abbas Hojati ◽  
Alireza Shirneshan
Keyword(s):  
Methyl Ester ◽  
Compression Ratio ◽  
Diesel Fuel ◽  
Release Rate ◽  
Experimental Tests ◽  
Waste Cooking Oil ◽  
Cylinder Pressure ◽  
Fuel Blend ◽  
Cooking Oil ◽  
Fuel Blends

In this research, a thermodynamic zero-dimensional model has been done to predict performance characteristics (in-cylinder pressure, heat released, and the thermal efficiency) of a diesel engine with the use of biodiesel–diesel fuel blends (B0, B20, B50, B80, and B100) at different compression ratios (14, 15, 16, 17, and 18). The corresponding mathematical and thermodynamic relationships have been solved in MATLAB. Based on the experimental tests, it was found that the developed model can predict the engine variables sufficiently. According to the results, the heat release rate and the cylinder pressure increased for all fuel blends by an increase in the compression ratio. Moreover, with the increasing biodiesel amount in the fuel blend (up to 50%) heat release rate and the cylinder pressure increased but these variables have a reduction when biodiesel percentage increases from 50 to 100 due to the lower heating value of waste cooking oil methyl ester in comparison with neat diesel fuel. Moreover, according to the experimental tests, carbon monoxide emission was reduced when biodiesel proportion increased in the fuel blend but the nitrogen oxides emitted from the engine enhanced when biodiesel amount in the fuel mixture increased. According to the results, it can be concluded that B50 has better combustion characteristics among all fuel blends.

Performance Characteristics of C.I. Engine with Bio-diesel Blends of Jatropha, Soya Bean Oil and Waste Cooking Oil at Fixed Compression Ratio

2018 ◽  
Vol 10 (3) ◽  
Author(s):  
Dinesh Ramchandani ◽  
Yogendra Rathore ◽  
R.K. Pandey
Keyword(s):  
Vegetable Oil ◽  
Compression Ratio ◽  
Diesel Fuel ◽  
Waste Cooking Oil ◽  
Performance Characteristics ◽  
Fuel Blend ◽  
Cooking Oil ◽  
Potential Alternative ◽  
Performance Check ◽  
A Performance

In this paper raw oil (jatropha, soybean and waste cooking fuel) is taken as potential alternative fuel for C.I. engines. The best distinction between these 3 kinds of oils and diesel fuel is viciousness. Every vegetable oil is blended with diesel in variable proportion (20% - 50%). Two sets of experiments are conducted for every fuel blend. First experiment is focussed on a performance check for pure diesel fuel. Second experiment is focussed on a performance check using many blends for each of Jatropha-diesel, soybean-diesel and waste cooking oil-diesel at fixed compression ratio of 18. The results of performance characteristics such as brake specific fuel consumption and brake thermal efficiency for every vegetable oil-diesel blends are compared with that using diesel fuel alone.

Impact of Diesel-Butanol-Waste Cooking Oil Biodiesel Blends on Stationary Diesel Engine Performance and Emission Characteristics

2020 ◽  
pp. 173-192
Author(s):  
H. Sharon ◽  
Joel Jackson R. ◽  
Prabha C.
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Specific Energy Consumption ◽  
Waste Cooking Oil ◽  
Nox Emission ◽  
Performance And Emission ◽  
Cooking Oil ◽  
Fuel Blends ◽  
Hydrocarbon Emission ◽  
Smoke Opacity

Feed stock cost and NOX emission are the major barriers for commercialization of biodiesel. Waste cooking oil is well identified as one of the cheapest feed stocks for biodiesel production. This chapter reduces NOX emission of waste cooking oil biodiesel. Test fuel blends are prepared by mixing diesel (20 to 50 v/v%), butanol (5 v/v%), and waste cooking oil biodiesel (45 to 75 v/v%). Fuel properties of waste cooking oil biodiesel are enhanced due to addition of diesel and butanol. Brake specific energy consumption of the blends is higher than diesel fuel. Harmful emissions like carbon monoxide, nitrous oxide, and smoke opacity are lower for blends than diesel fuel. Increasing biodiesel concentration in blend also reduces hydrocarbon emission to a significant extent. The obtained results justify the suitability of proposed cheap blends for diesel engine emission reduction.

scholarly journals Performance Measure of CI Engine by Varyingblends with Different Proportions and Parameters

2019 ◽  
Vol 8 (4) ◽  
pp. 12595-12598
Keyword(s):  
Methyl Ester ◽  
Alternative Fuels ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Performance Measure ◽  
Cooking Oil ◽  
Fuel Blends ◽  
Nozzle Injection ◽  
Automobile Engines ◽  
Ci Engine

Many researchers have been working on alternative fuels and it blends in order to enhance the performance of automobiles. There are number of alternative fuel blends have been tested on automobile engines and their performances have been analyzed. In this present work, Methyl Ester from Waste cooking oil to be prepared and going to blend with Diesel with different ratios, is an alternative fuel. The experiment is going to be conducted on the air cooled four stroke Diesel engine using these blends with different proportions and nozzle injection pressures, finally its performance characteristics to be analyzed.

AN ASSESSMENT OF VARIOUS NANOADDITIVES AND TRIBO-CORROSION WITH WASTE COOKING BIODIESEL FUELED IN A DIESEL ENGINE

2021 ◽  
Author(s):  
Yogaraj D ◽  
Jaichandar S
Keyword(s):  
Steady State ◽  
Diesel Fuel ◽  
Peak Load ◽  
Nox Emissions ◽  
Cylinder Pressure ◽  
Flash Temperature ◽  
Wear Scar Diameter ◽  
Fuel Blend ◽  
Fuel Blends ◽  
Temperature Parameter

The waste cooking biodiesel's steady-state coefficient of friction rate of fuel blends are B90 (18.2%), B60 (7.2%), B20 (16.72%), B10 (30.8%), and diesel (38.77%) higher compared with B40 fuel blend and wear scar diameter of the fuel blends from B40 to B100 had a minimal range of 0.5mm. The flash temperature parameter results higher from B40 to B100 fuel blends, and the corrosion rate was minimal for B40 and B50 fuel blends. Afterward, the fuel blend B40 (40% WCO+60% Diesel fuel) was chosen as fuel, along with Cerium (25ppm), Zinc (25ppm), and Titanium nanoparticles (25ppm) were selected as fuel additives. The B40+D60+Titanium (25ppm) blend resulted in improved BTE and 3.83% lowered BSEC comparison with diesel fuel. Then the fuel blend, B40+D80+Titanium (25ppm), resulted in 2.08% reduced HC, 36.36% CO, and 16.25% smoke emissions, along with marginally 8.5% higher NOx emissions comparison with diesel fuel. Also, the fuel blend, B40+D80+Titanium (25ppm) combustions characteristics are the equivalent trend of cylinder pressure (58.82 bar) and HRR (66.65 J/deg CA) related to diesel fuel at peak load.

scholarly journals Diesel Engine Performance, Emissions and Combustion Characteristics of Biodiesel and Its Blends Derived from Catalytic Pyrolysis of Waste Cooking Oil

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5708
Author(s):  
Mohamed Mohamed ◽  
Chee-Keong Tan ◽  
Ali Fouda ◽  
Mohammed Saber Gad ◽  
Osayed Abu-Elyazeed ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Potassium Hydroxide ◽  
Catalytic Pyrolysis ◽  
Pyrolysis Temperature ◽  
Waste Cooking Oil ◽  
Biodiesel Fuel ◽  
Engine Load ◽  
Cooking Oil ◽  
Fuel Blends ◽  
Blend Ratios

This paper first describes a slow catalytic pyrolysis process used for synthesizing biodiesel from waste cooking oil (WCO) as a feedstock. The influence of variations in the catalyst type (sodium hydroxide and potassium hydroxide), and catalyst concentration (0.5, 1.0, 3.0, 5.0, 7.0 and 10.0% by weight) on both the pyrolysis temperature range and biodiesel yield were investigated. The results suggested that sodium hydroxide (NaOH) was more effective than potassium hydroxide (KOH) as catalysts and that the highest yield (around 70 wt.%) was observed for a NaOH concentration of about 1 wt.% The resultant pyrolysis temperature range was also significantly lower for NaOH catalyst, thus suggesting overall lower energy consumption. Compared to conventional diesel, the synthesized biodiesel exhibited relatively similar physical properties and calorific value. The biodiesel was subsequently blended with diesel fuel in different blend ratios of 0, 20, 40, 60, 80 and 100% by volume of biodiesel and were later tested in a compression ignition engine. Brake thermal efficiency and specific fuel consumption were observed to be worse with biodiesel fuel blends particularly at higher engine load above 50%. However, NOx emission generally decreased with increasing blend ratio across all engine load, with greater reduction observed at higher engine load. Similar observation can also be concluded for CO emission. In contrast, lower hydrocarbon (HC) emission from the biodiesel fuel blends was only observed for blend ratios no higher than 40%. Particulate emission from the biodiesel fuel blends did not pose an issue given its comparable smoke opacity to diesel observed during the engine test. The in-cylinder peak pressures, temperature and heat release rate of biodiesel fuel blends were lower than diesel. Overall, biodiesel fuel blends exhibited shorter ignition delays when compared to diesel fuel.

scholarly journals Effect of Adding RON97 Into Waste Cooking Oil as an Alternative Fuel for Diesel Engine

2018 ◽  
Vol 7 (3.11) ◽  
pp. 113
Author(s):  
Idris Saad ◽  
Wardatul Hayah Ab Rashid ◽  
Nur Hidayah Saidon
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Calorific Value ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Fuel Blend ◽  
Cooking Oil ◽  
Blended Fuel ◽  
Blended Fuels ◽  
Conventional Diesel Fuel

Petroleum-based fuel reserves are drastically depleting due to a high demand on sustaining a better lifestyle. This paper presents the utilization of waste cooking oil (WCO) as an alternative fuel for diesel engine. Although WCO and conventional diesel fuel have similar physiochemical properties, the properties of WCO is considered inferior than conventional diesel fuel. It is due to higher viscosity and density of WCO while its calorific value is lower than conventional diesel fuel. In this research, unmodified WCO was blended with petrol fuel grade RON97.  Five blended fuels samples were prepared from five to 25 percent volume base with five percent step increment. The density and calorific value of all fuel blend samples together with unmodified WCO were measured and compared to the conventional diesel and RON97 fuels. Each of the blended fuel and conventional diesel were used to run a single cylinder diesel engine. The performance characteristic of the engine was recorded at different engine speeds ranging between 1500 and 3000 rpm. Results showed that the properties of blended fuel were inferior compared to the conventional diesel fuel; however, by adding 15 percent of RON97 into the unmodified WCO, the results were comparable to the conventional diesel fuel.  

Sign in / Sign up

Export Citation Format

Share Document