scholarly journals The combined plasticization of jute and tung oil anhydride for jute fiber reinforced poly(lactic acid) composites

2021 ◽  
pp. 096739112110576
Author(s):  
Ying Zhou ◽  
Can Chen ◽  
Lan Xie ◽  
Xiaolang Chen ◽  
Guangqiang Xiao ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Physical And Mechanical Properties ◽  
Complex Viscosity ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Sem Images ◽  
Pseudoplastic Fluid ◽  
Tung Oil ◽  
Biodegradable Poly ◽  
The Impact

In this work, novel plasticizing biodegradable poly (lactic acid) (PLA) composites were prepared by melt blending of jute and tung oil anhydride (TOA), and the physical and mechanical properties of PLA/jute/TOA composites were tested and characterized. The impact strength of PLA/jute/TOA composites significantly increases with increasing the content of TOA. The SEM images of fracture surface of PLA/jute/TOA composites become rough after the incorporation of TOA. In addition, TOA changes the crystallization temperature and decomposition process of PLA/jute/TOA composites. With increasing the amount of TOA, the value of storage modulus (E′) of PLA/jute/TOA composites gradually increases. The complex viscosity (η*) values for all samples reduce obviously with increasing the frequency, which means that the pure PLA and PLA/jute/TOA composites is typical pseudoplastic fluid. This is attributed to the formation of crosslinking, which restricts the deformation of the composites.

scholarly journals Impact Toughness and Ductility Enhancement of Biodegradable Poly(lactic acid)/Poly(ε-caprolactone) Blends via Addition of Glycidyl Methacrylate

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Wei Kit Chee ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Mohd Faizal Abd Rahman ◽  
Buong Woei Chieng
Keyword(s):  
Lactic Acid ◽  
Impact Strength ◽  
Glycidyl Methacrylate ◽  
Interfacial Adhesion ◽  
Tensile Modulus ◽  
Sem Analysis ◽  
Poly Lactic Acid ◽  
Biodegradable Poly ◽  
Interfacial Compatibility ◽  
The Impact

Poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blends were prepared via melt blending technique. Glycidyl methacrylate (GMA) was added as reactive compatibilizer to improve the interfacial adhesion between immiscible phases of PLA and PCL matrices. Tensile test revealed that optimum in elongation at break of approximately 327% achieved when GMA loading was up to 3wt%. Slight drop in tensile strength and tensile modulus at optimum ratio suggested that the blends were tuned to be deformable. Flexural studies showed slight drop in flexural strength and modulus when GMA wt% increases as a result of improved flexibility by finer dispersion of PCL in PLA matrix. Besides, incorporation of GMA in the blends remarkably improved the impact strength. Highest impact strength was achieved (160% compared to pure PLA/PCL blend) when GMA loading was up to 3 wt%. SEM analysis revealed improved interfacial adhesion between PLA/PCL blends in the presence of GMA. Finer dispersion and smooth surface of the specimens were noted as GMA loading increases, indicating that addition of GMA eventually improved the interfacial compatibility of the nonmiscible blend.

scholarly journals A review on graft compatibilizer for thermoplastic elastomer blend

2021 ◽  
Vol 2080 (1) ◽  
pp. 012003
Author(s):  
K.K. Nitiyah ◽  
Luqman Musa ◽  
M.S.M. Rasidi ◽  
Shayfull Zamree Abd Rahim ◽  
Rozyanty Rahman ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Natural Rubber ◽  
Thermoplastic Elastomer ◽  
Synthetic Polymers ◽  
The Other ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Internal Mixer ◽  
The Impact ◽  
Elastomer Blend

Abstract A biodegradable thermoplastic elastomer (TPE) blend is developed by blending poly (lactic acid) (PLA) and natural rubber (NR) or epoxidized natural rubber (ENR) and it is a sustainable substitution in recent years for synthetic polymers. PLA is high in mechanical strength and compostable, but it is highly stiff and brittle. The incorporation of NR or ENR to PLA increases the impact strength and toughness of PLA. However, the disparity in polarity between PLA and elastomer phase like NR and ENR results in TPE blend being incompatible. Hence, compatibilization is essential to improve its polarity and develop interactions. Compatibilizer that composed of two different polymer is known is graft compatibilizer with the aid of grafting agent. The graft compatibilizers are divided into two categories. The first type is made up of one polymer and grafting agent and, the other one is composed of two polymer groups and grafting agent. These two types of graft compatibilizer can be prepared via two different method such as direct melt blending and solution. Apart from this, the TPE blend is produced via the melt blending technique with mixing machines such as internal mixer and extruder. This article has reviewed the preparation of the graft compatibilizer and blending technique of TPE. Based on the findings, the graft compatibilizers has a significant role in improving miscibility and compatibility across blend composed of different phase.

Effect of chain extender on morphologies and properties of PBAT/PLA composites

2021 ◽  
pp. 089270572110514
Author(s):  
Jing Sun ◽  
Anrong Huang ◽  
Shanshan Luo ◽  
Min Shi ◽  
Jiling Song ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Rheological Properties ◽  
Chain Extender ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Elongation At Break ◽  
Increasing Trend ◽  
Biodegradable Poly ◽  
Interfacial Compatibility

Biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) (PBAT/PLA) composites were prepared by melt blending, and chain extender was used to improve the compatibility of PBAT/PLA blends through the chemical reaction. The influence of PLA and chain extender contents on mechanical properties, morphology, and rheological properties of PBAT/PLA composites was systematically investigated. The results revealed that the Young’s modulus and stress values gradually increased under the same strain, whereas the elongation at break decreased with the increase of chain extender content for PBAT/PLA (80/20) composites. Noteworthy, the presence of chain extender improves the interfacial compatibility between PLA and PBAT phases. At the chain extender content of 0.4, 0.6, and 0.8 wt.%, the extensional viscosity of the composites exhibited an increasing trend, whereas an obvious strain-hardening phenomenon emerged in the uniaxial extensional curves.

Biodegradable poly (lactic acid)/poly (butylene succinate) fibers with high elongation for health care products

2017 ◽  
Vol 88 (15) ◽  
pp. 1735-1744 ◽  
Author(s):  
Elwathig AM Hassan ◽  
Salah Eldin Elarabi ◽  
You Wei ◽  
Muhuo Yu
Keyword(s):  
Lactic Acid ◽  
Melt Spinning ◽  
Strength Loss ◽  
Poly Lactic Acid ◽  
Butylene Succinate ◽  
Morphological Studies ◽  
Biodegradable Poly ◽  
Spinning Process ◽  
High Elongation ◽  
The Impact

Poly (lactic acid)/poly (butylene succinate) (PLA/PBS) blend fibers with high miscibility and improved elongation with comparable mechanical strength were fabricated using the melt spinning process in order to reduce the impact on the environment by long-lasting plastics-based composites. The PLA/PBS blend fibers produced in different ratios have revealed high miscibility, which has been confirmed by morphological studies. The thermal properties showed the melting temperature of PLA at 167.13℃ and PLA/PBS blends at 169.18℃, and an increased content of PBS in blends also led to improved crystallinity. Importantly, during tensile testing, it is observed that the fracture behavior of the specimen changed from brittle fracture of neat PLA to ductile fracture of the blends, as demonstrated by the significant increase in the elongation at break with comparable tensile strength and modulus. Furthermore, the washing fastness, rubbing fastness, exhaustion values, strength loss, and shade depth ( K/ S value) for the knitted and dyed fibers were explored. It was found that the exhaustion and K/ S value increased when the temperature increased, but the strength decreased. The exhaustion and K/ S value of PLA/PBS blend fabrics improved compared to pure PLA fabric, with excellent washing and rubbing fastness.

scholarly journals Characterization of biodegradable poly(lactic acid) porous scaffolds prepared using selective enzymatic degradation for tissue engineering

RSC Advances ◽  
2017 ◽  
Vol 7 (54) ◽  
pp. 34063-34070 ◽  
Author(s):  
Ziqi Guo ◽  
Cheng Yang ◽  
Zuping Zhou ◽  
Shan Chen ◽  
Fan Li
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Enzymatic Degradation ◽  
Poly Lactic Acid ◽  
Porous Scaffolds ◽  
Sem Images ◽  
Biodegradable Poly

SEM images of MEF cells on PLA scaffolds prepared by selective enzymatic degradation after 7 days of culture. The results demonstrated that MEF cells attached more easily to the surface than in the interior of the PLA scaffolds.

Mechanical Properties and Phase Morphology of Poly(Lactic Acid)/Acrylonitrile-Butadiene Rubber/Organoclay Nanocomposites Prepared by Melt Blending

2018 ◽  
Vol 775 ◽  
pp. 13-19
Author(s):  
Sirirat Wacharawichanant ◽  
Kasana Chomphunoi ◽  
Chawisa Wisuttrakarn ◽  
Manop Phankokkruad
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Impact Strength ◽  
Phase Morphology ◽  
Poly Lactic Acid ◽  
Butadiene Rubber ◽  
Melt Blending ◽  
Acrylonitrile Butadiene Rubber ◽  
Internal Mixer ◽  
The Impact

This work investigated the mechanical properties and phase morphology of poly(lactic acid) (PLA)/acrylonitrile-butadiene rubber (NBR) blends and nanocomposites, which prepared by melt blending in an internal mixer. The contents of NBR were 5, 10, 15 and 20 wt% and the content of organoclay was 3 phr. The impact test showed that the impact strength of PLA/NBR blends increased with an increase of NBR content and the impact strength of the blends was more than eight times by adding NBR 10 wt% when compared with neat PLA. The tensile test showed that Young’s modulus and tensile strength of PLA/NBR blends and nanocomposites decreased after adding NBR and organoclay. While the strain at break of the NBR blends increased with increasing NBR content. This result is attributed to the rubber phase in NBR in a cause the increment of elongation and elasticity in PLA/NBR blends. The morphology of PLA/NBR blends observed the fractured surface was rougher than that of pure PLA. This observation indicates that the addition of NBR in PLA can change the brittle fracture of PLA to ductile fracture, which has an effect to the strain at break or elongation of PLA. However, the morphology of the PLA/NBR blends were also observed the phase separation of the dispersed NBR phase and PLA matrix phase, and appeared the voids in a polymer matrix. The addition of organoclay had an effect slightly on the morphology of the blends. From X-ray diffraction, results found that PLA/organoclay and PLA/NBR/organoclay nanocomposites showed the intercalated structure, which PLA chains were inserted into the interlayer of clay due to the increase of d-spacing.

scholarly journals Effect of talc and diatomite on compatible, morphological, and mechanical behavior of PLA/PBAT blends

e-Polymers ◽  
2021 ◽  
Vol 21 (1) ◽  
pp. 234-243
Author(s):  
Yue Ding ◽  
Cai Zhang ◽  
Congcong Luo ◽  
Ying Chen ◽  
Yingmei Zhou ◽  
...  
Keyword(s):  
Poly Lactic Acid ◽  
Melt Blending ◽  
Rheological Measurement ◽  
Elongation At Break ◽  
Biodegradable Poly ◽  
Green Packaging ◽  
Biodegradable Nanocomposites ◽  
Two Phases ◽  
The Impact ◽  
Good Possibility

Abstract Biodegradable nanocomposites were prepared by melt blending biodegradable poly(lactic acid) (PLA) and poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30, w/w) with diatomite or talc (1–7%). From the SEM test, the particles were transported to the interface of two phases, which acted as an interface modifier to strengthen the interfacial adhesion between PLA and PBAT. Talc and diatomite acted as nucleating agents to improve the crystallization of PBAT in the blends by DSC analysis. Moreover, adding the particles improved the tensile and impact toughness of the blends. The elongation at break with 5% talc was 78% (vs ∼21%) and the impact strength was 15 kJ/m2 (vs ∼6.5 kJ/m2). The rheological measurement revealed that the talc and diatomite reduced the viscosity of the blends. The results showed a good possibility of using talc- and diatomite-filled PLA/PBAT blends with high toughness for green-packaging and bio-membranes application.

Sign in / Sign up

Export Citation Format

Share Document