scholarly journals Effect of talc and diatomite on compatible, morphological, and mechanical behavior of PLA/PBAT blends

e-Polymers ◽  
2021 ◽  
Vol 21 (1) ◽  
pp. 234-243
Author(s):  
Yue Ding ◽  
Cai Zhang ◽  
Congcong Luo ◽  
Ying Chen ◽  
Yingmei Zhou ◽  
...  
Keyword(s):  
Poly Lactic Acid ◽  
Melt Blending ◽  
Rheological Measurement ◽  
Elongation At Break ◽  
Biodegradable Poly ◽  
Green Packaging ◽  
Biodegradable Nanocomposites ◽  
Two Phases ◽  
The Impact ◽  
Good Possibility

Abstract Biodegradable nanocomposites were prepared by melt blending biodegradable poly(lactic acid) (PLA) and poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30, w/w) with diatomite or talc (1–7%). From the SEM test, the particles were transported to the interface of two phases, which acted as an interface modifier to strengthen the interfacial adhesion between PLA and PBAT. Talc and diatomite acted as nucleating agents to improve the crystallization of PBAT in the blends by DSC analysis. Moreover, adding the particles improved the tensile and impact toughness of the blends. The elongation at break with 5% talc was 78% (vs ∼21%) and the impact strength was 15 kJ/m2 (vs ∼6.5 kJ/m2). The rheological measurement revealed that the talc and diatomite reduced the viscosity of the blends. The results showed a good possibility of using talc- and diatomite-filled PLA/PBAT blends with high toughness for green-packaging and bio-membranes application.

scholarly journals The combined plasticization of jute and tung oil anhydride for jute fiber reinforced poly(lactic acid) composites

2021 ◽  
pp. 096739112110576
Author(s):  
Ying Zhou ◽  
Can Chen ◽  
Lan Xie ◽  
Xiaolang Chen ◽  
Guangqiang Xiao ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Physical And Mechanical Properties ◽  
Complex Viscosity ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Sem Images ◽  
Pseudoplastic Fluid ◽  
Tung Oil ◽  
Biodegradable Poly ◽  
The Impact

In this work, novel plasticizing biodegradable poly (lactic acid) (PLA) composites were prepared by melt blending of jute and tung oil anhydride (TOA), and the physical and mechanical properties of PLA/jute/TOA composites were tested and characterized. The impact strength of PLA/jute/TOA composites significantly increases with increasing the content of TOA. The SEM images of fracture surface of PLA/jute/TOA composites become rough after the incorporation of TOA. In addition, TOA changes the crystallization temperature and decomposition process of PLA/jute/TOA composites. With increasing the amount of TOA, the value of storage modulus (E′) of PLA/jute/TOA composites gradually increases. The complex viscosity (η*) values for all samples reduce obviously with increasing the frequency, which means that the pure PLA and PLA/jute/TOA composites is typical pseudoplastic fluid. This is attributed to the formation of crosslinking, which restricts the deformation of the composites.

Effect of chain extender on morphologies and properties of PBAT/PLA composites

2021 ◽  
pp. 089270572110514
Author(s):  
Jing Sun ◽  
Anrong Huang ◽  
Shanshan Luo ◽  
Min Shi ◽  
Jiling Song ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Rheological Properties ◽  
Chain Extender ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Elongation At Break ◽  
Increasing Trend ◽  
Biodegradable Poly ◽  
Interfacial Compatibility

Biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) (PBAT/PLA) composites were prepared by melt blending, and chain extender was used to improve the compatibility of PBAT/PLA blends through the chemical reaction. The influence of PLA and chain extender contents on mechanical properties, morphology, and rheological properties of PBAT/PLA composites was systematically investigated. The results revealed that the Young’s modulus and stress values gradually increased under the same strain, whereas the elongation at break decreased with the increase of chain extender content for PBAT/PLA (80/20) composites. Noteworthy, the presence of chain extender improves the interfacial compatibility between PLA and PBAT phases. At the chain extender content of 0.4, 0.6, and 0.8 wt.%, the extensional viscosity of the composites exhibited an increasing trend, whereas an obvious strain-hardening phenomenon emerged in the uniaxial extensional curves.

Compatibility Enhancement of Poly(lactic Acid)/Crosslinked Starch Composite by Vacuum Heating Treatment

2011 ◽  
Vol 236-238 ◽  
pp. 207-215
Author(s):  
Xiao Gang Liu ◽  
Li Wang ◽  
Chen Yu Fan ◽  
Shi Zhong Li
Keyword(s):  
Lactic Acid ◽  
Solid Phase ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Heating Treatment ◽  
Two Phases ◽  
Vacuum Heating ◽  
The Cost ◽  
The Impact ◽  
Positive Effect

Compositing with starch is an effective way to lower the cost of the poly (lactic acid)(PLA)-based biodegradable materials, while the compatibility of these two phases needs to be enhanced. Here reports an improvement based on vacuum heating treatment(VHT), hence a solid-phase esterification between PLA and crosslinked starch（CST） is enhanced. This research also studied the impact by esterified catalysts and starch proportion on thermal stability, surface morphology and mechanical properties of the composite. The result indicated that VHT shows positive effect on all aspects. Especially, sample with 20% CST shows optimized tensile strength of 62.6 MPa, and elongation at break was as high as 69.8%.

Preparation and Properties Research of PA6/PLA Blends Toughening Modified by TPU

2012 ◽  
Vol 200 ◽  
pp. 278-281 ◽  
Author(s):  
Yi Chen ◽  
Wei Jian Xu ◽  
Guang Sheng Zeng ◽  
Xiao Hong Zeng ◽  
Wen Yong Liu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Fracture Behavior ◽  
Thermoplastic Polyurethane ◽  
Polyamide 6 ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Thermal And Mechanical Properties ◽  
Elongation At Break ◽  
The Impact

Polyamide 6/Poly(lactic acid) (PA6/PLA) blends introduce the degradability of PLA to high performance PA6, but the bad toughness of both PA6 and PLA limits the application of blends. Aiming at this deficiency, thermoplastic polyurethane (TPU) was used as an additive for modifying the toughness of PA6/PLA blends. PA6/PLA/TPU blends at various compositions were prepared by melt blending, the effects of blend compositions on the morphology, thermal and mechanical properties of blends were investigated. The results showed that the addition of TPU improves the compatibilization between PA6 and PLA and makes the blends show more obvious plastic fracture behavior than PA6/PLA.When the content of PLA in PA6/PLA increases, the impact and tensile strength of blends decrease slightly with the intense decrease of the elongation at break, adding TPU into PA6/PLA blends strengthens the toughness of blends, but the tensile strength of blends decreases. Moreover, the crystallinity of PA6 /PLA blend is hampered by TPU.

Mechanical, Thermal, and Morphological Properties of Thermoplastic Starch/Poly(lactic acid/Poly(butylene adipate-co-terephthalate) Blends

2014 ◽  
Vol 970 ◽  
pp. 312-316
Author(s):  
Sujaree Tachaphiboonsap ◽  
Kasama Jarukumjorn
Keyword(s):  
Lactic Acid ◽  
Impact Strength ◽  
Interfacial Adhesion ◽  
Tensile Modulus ◽  
Thermoplastic Starch ◽  
Morphological Properties ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Elongation At Break ◽  
Blending Method

Thermoplastic starch (TPS)/poly (lactic acid) (PLA) blend and thermoplastic starch (TPS)/poly (lactic acid) (PLA)/poly (butylene adipate-co-terephthalate) (PBAT) blend were prepared by melt blending method. PLA grafted with maleic anhydride (PLA-g-MA) was used as a compatibilizer to improve the compatibility of the blends. As TPS was incorporated into PLA, elongation at break was increased while tensile strength, tensile modulus, and impact strength were decreased. Tensile properties and impact properties of TPS/PLA blend were improved with adding PLA-g-MA indicating the enhancement of interfacial adhesion between PLA and TPS. With increasing PBAT content, elongation at break and impact strength of TPS/PLA blends were improved. The addition of TPS decreased glass transition temperature (Tg), crystallization temperature (Tc), and melting temperature (Tm) of PLA. Tgand Tcof TPS/PLA blend were decreased by incorporating PLA-g-MA. However, the presence of PBAT reduced Tcof TPS/PLA blend. Thermal properties of TPS/PLA/PBAT blends did not change with increasing PBAT content. SEM micrographs revealed that the compatibilized TPS/PLA blends exhibited finer morphology when compared to the uncompatibilized TPS/PLA blend.

scholarly journals Impact Toughness and Ductility Enhancement of Biodegradable Poly(lactic acid)/Poly(ε-caprolactone) Blends via Addition of Glycidyl Methacrylate

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Wei Kit Chee ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Mohd Faizal Abd Rahman ◽  
Buong Woei Chieng
Keyword(s):  
Lactic Acid ◽  
Impact Strength ◽  
Glycidyl Methacrylate ◽  
Interfacial Adhesion ◽  
Tensile Modulus ◽  
Sem Analysis ◽  
Poly Lactic Acid ◽  
Biodegradable Poly ◽  
Interfacial Compatibility ◽  
The Impact

Poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blends were prepared via melt blending technique. Glycidyl methacrylate (GMA) was added as reactive compatibilizer to improve the interfacial adhesion between immiscible phases of PLA and PCL matrices. Tensile test revealed that optimum in elongation at break of approximately 327% achieved when GMA loading was up to 3wt%. Slight drop in tensile strength and tensile modulus at optimum ratio suggested that the blends were tuned to be deformable. Flexural studies showed slight drop in flexural strength and modulus when GMA wt% increases as a result of improved flexibility by finer dispersion of PCL in PLA matrix. Besides, incorporation of GMA in the blends remarkably improved the impact strength. Highest impact strength was achieved (160% compared to pure PLA/PCL blend) when GMA loading was up to 3 wt%. SEM analysis revealed improved interfacial adhesion between PLA/PCL blends in the presence of GMA. Finer dispersion and smooth surface of the specimens were noted as GMA loading increases, indicating that addition of GMA eventually improved the interfacial compatibility of the nonmiscible blend.

scholarly journals Investigation on compatibility of PLA/PBAT blends modified by epoxy-terminated branched polymers through chemical micro-crosslinking

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Bo Wang ◽  
Yujuan Jin ◽  
Kai’er Kang ◽  
Nan Yang ◽  
Yunxuan Weng ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Glass Transition ◽  
Sem Analysis ◽  
Branched Polymers ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
The Difference ◽  
Physical And Chemical ◽  
The Impact

AbstractIn this study, a type of epoxy-terminated branched polymer (ETBP) was used as an interface compati- bilizer to modify the poly lactic acid (PLA)/poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30) blends. Upon addition of ETBP, the difference in glass transition temperature between PLA and PBAT became smaller. By adding 3.0 phr of ETBP, the elongation at break of the PLA/PBAT blends was found increased from 45.8% to 272.0%; the impact strength increased from 26.2 kJ·m−2 to 45.3 kJ·m−2. In SEM analysis, it was observed that the size of the dispersed PBAT particle decreased with the increasing of ETBP content. These results indicated that the compatibility between PLA and PBAT can be effectively enhanced by using ETBP as the modifier. The modification mechanism was discussed in detail. It proposes that both physical and chemical micro-crosslinking were formed, the latter of which was confirmed by gel content analysis.

Toughening Modification of Poly(butylene terephthalate)/Polycarbonate Blends by Poly(ethylene-co-octene)

2005 ◽  
Vol 13 (4) ◽  
pp. 385-394
Author(s):  
Huiyu Bai ◽  
Yong Zhang ◽  
Yinxi Zhang ◽  
Xiangfu Zhang ◽  
Wen Zhou
Keyword(s):  
Average Diameter ◽  
Melt Blending ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Bisphenol A Polycarbonate ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
Twin Screw ◽  
Poly Ethylene ◽  
The Impact

New toughened poly(butylene terephthalate) (PBT)/bisphenol A polycarbonate (PC) blends were obtained by melt blending with commercial poly(ethylene-co-octene) copolymer (POE), varying the POE content up to 10 wt%, in a twin screw extruder, followed by injection moulding. The influence of POE on the properties of the PBT/PC blends was investigated in terms of mechanical testing, dynamic mechanical thermal (DMTA) analysis, differential scanning calorimetry (DSC), and scanning electronic microscopy (SEM). The results showed that addition of POE led to remarkable increases in the impact strength, elongation at break and Vicat temperature, and a reduction in the tensile strength and flexural properties of PBT/PC blends. The morphology of the blends was observed using SEM and the average diameter of the dispersed phase was determined by image analysis. The critical inter-particle distance for PBT/PC was determined.

Structure-property relationship of biodegradable poly(butylene succinate)/polycaprolactone coated inorganic particle composites

2013 ◽  
Vol 33 (2) ◽  
pp. 111-119
Author(s):  
Yiming Liu ◽  
Qing Liu ◽  
Bing Meng ◽  
Zhihua Wu
Keyword(s):  
Impact Strength ◽  
High Speed ◽  
Complex Viscosity ◽  
Structure Property ◽  
Scanning Calorimetry ◽  
Butylene Succinate ◽  
Elongation At Break ◽  
Inorganic Particle ◽  
Biodegradable Poly ◽  
The Impact

Abstract Polycaprolactone (PCL)-coated micro kaolin and nano-titania were prepared by high-speed hybrid mechanical coating. Poly(butylene succinate) (PBS)-coated inorganic particle composites were prepared by the melt-blending process. The influence of coated kaolin microparticles on the dynamic rheological behavior, non-isothermal crystallization behavior, micromorphology, and mechanical behavior were investigated. The effect of coated nano-titania on the mechanical properties of PBS-coated kaolin composites was also studied. A dynamic rheological property indicates that the complex viscosity of PBS-coated kaolin microcomposites is higher than neat PBS. Differential scanning calorimetry (DSC) implies that the micrometric size of kaolin particles restrains the crystallization of PBS. Scanning electronic microscopy (SEM) reveals a well dispersed state of coated kaolin in the polymer matrix. The impact strength of PBS-coated kaolin microcomposites is improved, while the tensile strength and elongation at break is decreased, but still appreciable. The introduction of coated nano-titania improves the impact strength dramatically, and the elongation at break of composites is considerable.

scholarly journals A study on the mechanical, thermal properties and crystallization behavior of poly(lactic acid)/thermoplastic poly(propylene carbonate) polyurethane blends

RSC Advances ◽  
2017 ◽  
Vol 7 (73) ◽  
pp. 46183-46194 ◽  
Author(s):  
Jia Yang ◽  
Hongwei Pan ◽  
Xin Li ◽  
Shulin Sun ◽  
Huiliang Zhang ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Thermal Properties ◽  
Impact Strength ◽  
Propylene Carbonate ◽  
Crystallization Behavior ◽  
Raw Materials ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Poly Propylene ◽  
The Impact

PPCU was prepared by using PPC and polyols as the raw materials and diphenyl-methane-diisocyanate (MDI) as the extender chain. The impact strength and elongation at break of PLA were remarkably enhanced by blending with PPCU.

Sign in / Sign up

Export Citation Format

Share Document