Shear-flexural cracking strength of RC beams with external vertical prestressing rebars: Theoretical investigation and numerical simulation

2021 ◽  
pp. 136943322110606
Author(s):  
Zhou Junlong ◽  
Li Dongsheng
Keyword(s):  
Concrete Strength ◽  
Finite Element Models ◽  
Rc Beam ◽  
Vertical Stiffness ◽  
Shear Span ◽  
Depth Ratio ◽  
Longitudinal Tension ◽  
Pulling Force ◽  
Small Shear ◽  
Strength Improvement

This paper presents a semi-theoretical empirical formula to predict the shear-flexural cracking strength of an RC beam enhanced with the external vertical prestressing rebar (EVPR) technique. Besides, nonlinear finite element models (FEM) created by software ABAQUS were used to analyze the effect of crucial parameters on the shear-flexural cracking strength. The parameters involve shear span-to-depth ratio, concrete strength, longitudinal tension reinforcement ratio, initial pulling force and spacing of EVPRs, and the vertical stiffness of the EVPR supports. Results show that the cracking strength increased linearly with the tensile strength of the concrete and the initial pulling force. The small shear span-to-depth ratio was predominantly conducive to the cracking strength. Adequate longitudinal tension rebars contributed to the cracking strength improvement. A reasonable EVPR spacing was recommended to ensure the cracking strength. Greater vertical stiffness of the EVPR supports can ensure higher compressive stress for the RC beam to improve the cracking strength.

scholarly journals Behavior of self-compact reinforced concrete deep beams with small shear span to depth ratio

2018 ◽  
Vol 162 ◽  
pp. 04013
Author(s):  
Hassan Hassan ◽  
Mu’taz Medhlom ◽  
Mohammed Hatem
Keyword(s):  
Concrete Strength ◽  
Experimental Program ◽  
Deep Beams ◽  
Shear Span ◽  
Finite Element Software ◽  
Strut And Tie ◽  
Depth Ratio ◽  
Rc Deep Beams ◽  
Predicted Values ◽  
Small Shear

This research is devoted to investigate the experimental and theoretical behavior of deep beams under monotonic two points loading. An experimental program examining six RC deep beams is carried out. The investigated parameters include shear span to depth ratio varying from 1.0 to 0.276. A comparative study is conducted in this paper by using finite element software ANSYS. The experimental and numerical results show that concrete strength and shear span to depth ratio are the two most important parameters in controlling the behavior of RC deep beams. Comparison of experimental results was made with corresponding predicted values using the Strut and Tie procedure presented ACI 318M-11Code and with other procedures mentioned in the literature. It was found that the Strut and Tie procedure presented in ACI 318M-11Code give conservative results as compared with the experimental tested results. The results showed reliability of analysis in predicting deep beams behavior in terms of failure load, failure mode as well as crack propagation.

scholarly journals Shear behavior degradation and failure pattern of reinforced concrete beam with chloride-induced stirrup corrosion

2019 ◽  
Vol 22 (14) ◽  
pp. 2998-3010 ◽  
Author(s):  
Zhao-Hui Lu ◽  
Hai Li ◽  
Wengui Li ◽  
Yan-Gang Zhao ◽  
Zhuo Tang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Strength ◽  
Shear Behavior ◽  
Reinforced Concrete Beams ◽  
Failure Pattern ◽  
Reinforcement Corrosion ◽  
Shear Span ◽  
Depth Ratio

Reinforcement corrosion exhibits an adverse effect on the shear strength of reinforced concrete structures. In order to investigate the effects of chloride-induced corrosion of reinforcing steel on the shear behavior and failure pattern of reinforced concrete beams, a total of 24 reinforced concrete beams with different concrete strength grades and arrangements of stirrups were fabricated, among which 22 beams were subjected to accelerated corrosion to achieve different degrees of reinforcement corrosion. The failure pattern, crack propagation, load–displacement response, and ultimate strength of these beams were investigated under a standard four-point loading test in this study. Extensive comparative analysis was conducted to investigate the effects of the concrete strength, shear span-to-depth ratio, and stirrup type on the shear behavior of the corroded reinforced concrete beams. The results show that increasing the stirrup yielding strength is more effective in improving the shear strength of corroded reinforced concrete beams than that of concrete compressive strength. In terms of three types of stirrups, the shear strength of the beams with deformed HRB-335 is least sensitive to stirrup corrosion, followed by the beams with smooth HPB-235 and the beams with deformed HRB-400. The effect of the different stirrups on the shear strength depends on the corrosion degree of stirrup and shear span-to-depth ratio of the beam. The predicted results of shear strength of corroded reinforced concrete beams by a proposed analytical model are well consistent with the experimental results.

scholarly journals Experimental Study on Shear Capacity of High Strength Reinforcement Concrete Deep Beams with Small Shear Span–Depth Ratio

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1218 ◽  
Author(s):  
Jun-Hong Zhang ◽  
Shu-Shan Li ◽  
Wei Xie ◽  
Yang-Dong Guo
Keyword(s):  
High Strength ◽  
Shear Capacity ◽  
Reinforcement Ratio ◽  
Longitudinal Reinforcement ◽  
Deep Beams ◽  
Shear Span ◽  
Depth Ratio ◽  
Diagonal Compression ◽  
Web Reinforcement ◽  
Small Shear

This study aimed to investigate the shear capacity performance for eight deep beams with HTRB600 reinforced high strength concrete under concentrated load to enable a better understanding of the effects of shear span–depth ratio, longitudinal reinforcement ratio, vertical stirrup ratio and in order to improve design procedures. The dimension of eight test specimens is 1600 mm × 200 mm × 600 mm. The effective span to height ratio l0/h is 2.0, the shear span–depth ratio λ is 0.3, 0.6 and 0.9, respectively. In addition, the longitudinal reinforcement ratio ρs is set to 0.67%, 1.05%, 1.27%, and the vertical stirrup ratio is taken to be 0%, 0.25%, 0.33%, 0.5%. Through measuring the strain of steel bar, the strain of concrete and the deflection of mid-span, the characteristics of the full process of shear capacity, the failure mode and the load deflection deformation curve were examined. The test results showed that the failure mode of deep beams with small shear span–depth ratio is diagonal compression failure, which is influenced by the layout and quantity of web reinforcement. The diagonal compression failure could be classified into two forms: crushing-strut and diagonal splitting. With decreasing of shear span–depth ratio and increasing longitudinal reinforcement ratio, the shear capacity of deep beams increases obviously, while the influence of vertical web reinforcement ratio on shear capacity is negligible. Finally, the shear capacity of eight deep beams based on GB 50010-2010 is calculated and compared with the calculation results of ACI 318-14, EN 1992-1-1:2004 and CSA A23.3-04, which are based on strut-and-tie model. The obtained results in this paper show a very good agreement with GB50010-2010 and ACI 318-14, while the results of EN 1992-1-1:2004 and CSA A23.3-04 are approved to be conservative.

Numerical Verification of Strut and Tie Models and Failure Modes of Reinforced Self-Compacting Concrete Deep Beams

2021 ◽  
Vol 53 ◽  
pp. 76-100
Author(s):  
Mutiu Adelodun Akinpelu ◽  
Bilyamin Adeoye Ibitoye ◽  
Samson Olalekan Odeyemi ◽  
Kabir Opeyemi Olorede
Keyword(s):  
Failure Modes ◽  
Concrete Strength ◽  
Numerical Verification ◽  
Nonlinear Behaviour ◽  
Finite Model ◽  
Deep Beams ◽  
Self Compacting Concrete ◽  
Shear Span ◽  
Strut And Tie ◽  
Depth Ratio

This study utilized Finite Element Method (FEM) to analyse the structural behaviour and failure modes of Reinforced Self Compacting Concrete (RSCC) deep beams. Eighteen deep beam specimens subjected to four-point loadings were modelled and analyzed using Abaqus modelling tool. Damage plasticity model was used to characterised the nonlinear behaviour of concrete material while linear elastic, linear-plastic-hardening model represented the reinforcing steel material behaviour. The results of the finite model were compared with four different Strut and Tie Models (STMs) using one-way Analysis of Variance (ANOVA). Results of the numerical study revealed that the concrete strength and shear span to depth ratio mostly affect the load-deflection response of the beams. Also, the failure modes of the studied deep beams were influenced by shear span to depth ratio, concrete strength as well as web reinforcement distribution. The ANOVA results also showed that the FEM outperformed the existing STMs.

scholarly journals Influence of Patching on the Shear Failure of Reinforced Concrete Beam without Stirrup

2021 ◽  
Vol 6 (7) ◽  
pp. 97
Author(s):  
Stefanus Adi Kristiawan ◽  
Halwan Alfisa Saifullah ◽  
Agus Supriyadi
Keyword(s):  
Reinforced Concrete ◽  
Shear Failure ◽  
Numerical Study ◽  
Unsaturated Polyester ◽  
Reinforced Concrete Beam ◽  
Concrete Cover ◽  
Shear Capacity ◽  
Rc Beam ◽  
Shear Span ◽  
Shear Cracking

Deteriorated concrete cover, e.g., spalling or delamination, especially when it occurs at the web of a reinforced concrete (RC) beam within the shear span, can reduce the shear capacity of the beam. Patching of this deteriorated area may be the best option to recover the shear capacity of the beam affected. For this purpose, unsaturated polyester resin mortar (UPR mortar) has been formulated. This research aims to investigate the efficacy of UPR mortar in limiting the shear cracking and so restoring the shear capacity of the deteriorated RC beam. The investigation is carried out by an experimental and numerical study. Two types of beams with a size of 150 × 250 × 1000 mm were prepared. The first type of beams was assigned as a normal beam. The other was a beam with a cut off in the non-stirrup shear span, which was eventually patched with UPR mortar. Two reinforcement ratios were assigned for each type of beams. The results show that UPR mortar is effective to hamper the propagation of diagonal cracks leading to increase the shear failure load by 15–20% compared to the reference (normal) beam. The increase of shear strength with the use of UPR mortar is consistently confirmed at various reinforcement ratios.

Sign in / Sign up

Export Citation Format

Share Document