scholarly journals Investigating the impact of gasoline composition on PN in GDI engines using an improved measurement method

2020 ◽  
pp. 146808742097037
Author(s):  
Charles Bokor ◽  
Behzad Rohani ◽  
Charlie Humphries ◽  
Denise Morrey ◽  
Fabrizio Bonatesta
Keyword(s):  
Direct Injection ◽  
Exhaust System ◽  
Injection Pressure ◽  
Gasoline Direct Injection ◽  
Engine Operation ◽  
Accuracy Of Measurements ◽  
Particulate Number ◽  
Grade Performance ◽  
Gdi Engines ◽  
The Impact

An experimental investigation was carried out to investigate Particulate Number (PN) emissions from a modern, small-capacity Gasoline Direct Injection (GDI) engine. The first part of the study focused on improving measurement repeatability using the Cambustion DMS-500 device. Results showed that sampling near the exhaust valve – while dampening the pressure oscillations in the sampling line – can significantly improve the repeatability. It was also found that uncontrolled phenomena such as deposition in the exhaust system from earlier engine operation can undermine the accuracy of measurements taken at tailpipe level. The second part of the work investigated PN emissions from three types of gasoline fuel, Pump-grade, Performance and Reference. Fuel chemical composition was found to have an appreciable impact on PN, but the magnitude of this effect differs in various operating points, being more pronounced at higher engine load. The Reference fuel was found to have the lowest PN emission tendency, conceivably because of its lower aromatics, olefins and heavy hydrocarbons content. A sweep of operating parameters showed that higher injection pressure reduces PN, but the extent of the reduction depends on fuel physical properties such as volatility.

Multi-component fuel vaporization modelling and its effect on spray development in gasoline direct injection engines

2007 ◽  
Vol 221 (10) ◽  
pp. 1321-1342 ◽  
Author(s):  
S Tonini ◽  
M Gavaises ◽  
C Arcoumanis ◽  
A Theodorakakos ◽  
S Kometani
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Injection System ◽  
Fuel Spray ◽  
Mixing Processes ◽  
Engine Operation ◽  
Fuel Vaporization ◽  
Swirl Atomizer ◽  
Gdi Engines

A multi-component fuel vaporization model has been developed and implemented into an in-house multi-phase computational fluid dynamics flow solver simulating the flow, spray, and air-fuel mixing processes taking place in gasoline direct injection (GDI) engines. Multi-component fuel properties are modelled assuming a specified composition of pure hydrocarbons. High-pressure and -temperature effects, as well as gas solubility and compressibility, are considered. Remote droplet vaporization is initially investigated in order to quantify and validate the most appropriate vaporization model for conditions relevant to those realized with GDI engines. Phenomena related to the fuel injection system and pressure-swirl atomizer flow as well as the subsequent spray development are considered using an one-dimensional fuel injection equipment model predicting the wave dynamics inside the injection system, a Eulerian volume of fluid-based two-phase flow model simulating the liquid film formation process inside the injection hole of the swirl atomizer and a Lagrangian spray model simulating the subsequent spray development, respectively. The computational results are validated against experimental data obtained in an optical engine and include laser Doppler velocimetry measurements of the charge air motion in the absence of spray injection and charge coupled device images of the fuel spray injected during the induction stroke. The results confirm that fuel composition affects the overall fuel spray vaporization rate, but not significantly relative to other flow and heat transfer processes taking place during the engine operation.

scholarly journals Irregular ignition events in TC GDI engines: phenomenology, analysis and engine development

2010 ◽  
Vol 143 (4) ◽  
pp. 23-30
Author(s):  
Alois HIRSCH ◽  
Paul KAPUS ◽  
Harald PHILIPP ◽  
Ernst WINKLHOFER
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Measurement Techniques ◽  
Gasoline Direct Injection ◽  
Engine Operation ◽  
Measurement And Analysis ◽  
Engine Testing ◽  
Ignition And Combustion ◽  
Gdi Engines ◽  
Engine Development

Gasoline engine development has to respond to requirements for fuel efficient and clean combustion. In meeting such targets, the automotive industry has responded with the introduction and continuous improvement of turbocharged gasoline direct injection (TC GDI) combustion systems. Specific challenges to such engines include irregular ignition and combustion events which are rarely met in conventional engines. The paper describes ignition phenomena and mechanisms relevant for the development of such TC GDI engines. Focus then is given to combustion measurement techniques applied for the identification of these spontaneous and riskfull combustion events. As analysis of such ignition events must be done in real, high load multicylinder engine operation, suitable sensors together with measurement and analysis procedures are described. The paper concludes with analysis examples derived from various engine testing situations.

scholarly journals Comparison of primary aerosol emission and secondary aerosol formation from gasoline direct injection and port fuel injection vehicles

2018 ◽  
Vol 18 (12) ◽  
pp. 9011-9023 ◽  
Author(s):  
Zhuofei Du ◽  
Min Hu ◽  
Jianfei Peng ◽  
Wenbin Zhang ◽  
Jing Zheng ◽  
...  
Keyword(s):  
Volatile Organic Compounds ◽  
Organic Compounds ◽  
Fuel Injection ◽  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Vehicle Exhaust ◽  
Port Fuel Injection ◽  
Gasoline Vehicles ◽  
Volatile Organic ◽  
The Impact

Abstract. Gasoline vehicles significantly contribute to urban particulate matter (PM) pollution. Gasoline direct injection (GDI) engines, known for their higher fuel efficiency than that of port fuel injection (PFI) engines, have been increasingly employed in new gasoline vehicles. However, the impact of this trend on air quality is still poorly understood. Here, we investigated both primary emissions and secondary organic aerosol (SOA) formation from a GDI and a PFI vehicle under an urban-like driving condition, using combined approaches involving chassis dynamometer measurements and an environmental chamber simulation. The PFI vehicle emits slightly more volatile organic compounds, e.g., benzene and toluene, whereas the GDI vehicle emits more particulate components, e.g., total PM, elemental carbon, primary organic aerosols and polycyclic aromatic hydrocarbons. Strikingly, we found a much higher SOA production (by a factor of approximately 2.7) from the exhaust of the GDI vehicle than that of the PFI vehicle under the same conditions. More importantly, the higher SOA production found in the GDI vehicle exhaust occurs concurrently with lower concentrations of traditional SOA precursors, e.g., benzene and toluene, indicating a greater contribution of intermediate volatility organic compounds and semi-volatile organic compounds in the GDI vehicle exhaust to the SOA formation. Our results highlight the considerable potential contribution of GDI vehicles to urban air pollution in the future.

Experimental and numerical analyses of the combustion process in a direct injection gasoline engine

2000 ◽  
Vol 1 (2) ◽  
pp. 147-161 ◽  
Author(s):  
J Reissing ◽  
H Peters ◽  
J. M. Kech ◽  
U Spicher
Keyword(s):  
Numerical Investigation ◽  
Gasoline Engine ◽  
Numerical Models ◽  
Direct Injection ◽  
Combustion Process ◽  
Experimental Methods ◽  
Spark Ignition Engine ◽  
Gasoline Direct Injection ◽  
Direct Injection Gasoline Engine ◽  
Gdi Engines

Gasoline direct injection (GDI) spark ignition engine technology is advancing at a rapid rate. The development and optimization of GDI engines requires new experimental methods and numerical models to analyse the in-cylinder processes. Therefore the objective of this paper is to present numerical and experimental methods to analyse the combustion process in GDI engines. The numerical investigation of a four-stroke three-valve GDI engine was performed with the code KIVA-3V [1]. For the calculation of the turbulent combustion a model for partially premixed combustion, developed and implemented by Kech [4], was used. The results of the numerical investigation are compared to experimental results, obtained using an optical fibre technique in combination with spectroscopic temperature measurements under different engine conditions. This comparison shows good agreement in temporal progression of pressure. Both the numerical simulation and the experimental investigation predicted comparable combustion phenomena.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

Sign in / Sign up

Export Citation Format

Share Document