Optimal interstage liner design: A parametric study

2021 ◽  
pp. 1475472X2110368
Author(s):  
Ana Luisa P Maldonado ◽  
R Jeremy Astley
Keyword(s):  
Swirling Flow ◽  
Rotor Blades ◽  
Frequency Range ◽  
Flow Conditions ◽  
Mean Flow ◽  
Guide Vanes ◽  
Turbofan Engines ◽  
Surface Areas ◽  
Current Trends ◽  
Equal Power

The current trends for next generation turbofan engines are towards shorter nacelles and increased distances between the fan and the outlet guide vanes. This leads to an overall reduction in lined surface areas as well as an increase in the relative importance of the interstage liner, which is the liner placed between the rotor blades and the stator vanes. So far most of the efforts have been on liners for intakes and bypass ducts. The interstage is different in that the liner is subject to a mean flow with a strong swirl component and shear. The focus of this paper is on the effect of swirling flow on optimal liner attenuation in the interstage region. A broadband source downstream at the Outlet Guide Vanes (OGV) consisting of all propagating modes with equal power in each mode is used. Optimum impedance plots are generated for approach and take-off mean flow conditions. The effect of swirl on liner optimum resistance and reactance and optimum insertion loss is observed for a frequency range characteristic of real turbofan engines.

Planar Investigation of Outlet Boundary Conditions Effect on Isothermal Flow Fields of a Swirl-Stabilized Burner

2009 ◽  
Author(s):  
Ahmed Emara ◽  
Arnaud Lacarelle ◽  
Christian Oliver Paschereit
Keyword(s):  
Coherent Structures ◽  
Swirling Flow ◽  
Streamwise Velocity ◽  
Flow Conditions ◽  
Mean Flow ◽  
Cold Flow ◽  
Contraction Ratio ◽  
The Mean ◽  
Pod Analysis ◽  
Proper Orthogonal

The swirling flow velocity profiles can be strongly influenced by the outlet conditions of the combustion chamber especially at subcritical flow conditions. The effect of such changes on the mean flow or coherent structures is still unclear. It is investigated in the present work in an industrial swirl inducing burner in cold flow conditions with help of PIV. Proper orthogonal decomposition (POD) as well as acoustic measurements were used to characterize the coherent structures shed from the burner mouth. The combustor length (670, and 2020mm) and the outlet area contraction ratio (1, 0.56, 0.27, and 0.09) are varied. Major changes in the flow field are achieved when using a short combustor and the smallest contraction ratio. For this case, a central jet with streamwise velocity is added to the typical central recirculation zone. The POD analysis of the contraction ratios 1 and 0.09 for the long combustor shows that the first helical mode as well as Kelvin Helmholtz vortices are present with minor changes for both cases. At a contraction ratio of 0.09, some new structures at the jet location and near the combustor wall appear.

scholarly journals Quantifying the Effects of Wave—Current Interactions on Tidal Energy Resource at Sites in the English Channel Using Coupled Numerical Simulations

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3625
Author(s):  
Jon Hardwick ◽  
Ed B. L. Mackay ◽  
Ian G. C. Ashton ◽  
Helen C. M. Smith ◽  
Philipp R. Thies
Keyword(s):  
Wave Model ◽  
Tidal Energy ◽  
English Channel ◽  
Flow Conditions ◽  
Mean Flow ◽  
Radiation Stress ◽  
Large Wave ◽  
Stress Gradients ◽  
The Mean ◽  
Flow Power

Numerical modeling of currents and waves is used throughout the marine energy industry for resource assessment. This study compared the output of numerical flow simulations run both as a standalone model and as a two-way coupled wave–current simulation. A regional coupled flow-wave model was established covering the English Channel using the Delft D-Flow 2D model coupled with a SWAN spectral wave model. Outputs were analyzed at three tidal energy sites: Alderney Race, Big Roussel (Guernsey), and PTEC (Isle of Wight). The difference in the power in the tidal flow between coupled and standalone model runs was strongly correlated to the relative direction of the waves and currents. The net difference between the coupled and standalone runs was less than 2.5%. However, when wave and current directions were aligned, the mean flow power was increased by up to 7%, whereas, when the directions were opposed, the mean flow power was reduced by as much as 9.6%. The D-Flow Flexible Mesh model incorporates the effects of waves into the flow calculations in three areas: Stokes drift, forcing by radiation stress gradients, and enhancement of the bed shear stress. Each of these mechanisms is discussed. Forcing from radiation stress gradients is shown to be the dominant mechanism affecting the flow conditions at the sites considered, primarily caused by dissipation of wave energy due to white-capping. Wave action is an important consideration at tidal energy sites. Although the net impact on the flow power was found to be small for the present sites, the effect is site specific and may be significant at sites with large wave exposure or strong asymmetry in the flow conditions and should thus be considered for detailed resource and engineering assessments.

Improvement of Stalling Characteristics of an Axial-Flow Fan by Radial-Vaned Air-Separators

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
Nobuyuki Yamaguchi ◽  
Masayuki Ogata ◽  
Yohei Kato
Keyword(s):  
Solid Wall ◽  
Axial Flow ◽  
Internal Flow ◽  
Rotor Blades ◽  
Relative Location ◽  
Flow Conditions ◽  
Axial Flow Fan ◽  
Light Load ◽  
Stall Prevention ◽  
Air Separator

An improved construction of air-separator device, which has radial-vanes embedded within its inlet circumferential opening with their leading-edges facing the moving tips of the fan rotor-blades so as to scoop the tip flow, was investigated with respect to the stall-prevention effect on a low-speed, single-stage, lightly loaded, axial-flow fan. Stall-prevention effects by the separator layout, relative location of the separator to the rotor-blades, and widths of the openings of the air-separator inlet and exit were parametrically surveyed. As far as the particular fan is concerned, the device together with the best relative location has proved to be able to eliminate effectively the stall zone having existed in the original solid-wall characteristics, which has confirmed the promising potential of the device. Guidelines were obtained from the data for optimizing relative locations of the device to the rotor-blades, maximizing the stall-prevention effect of the device, and minimizing the axial size of the device for a required stall-prevention effect, at least for the particular fan and possibly for fans of similar light-load fans. The data suggest the changing internal flow conditions affected by the device conditions.

Generation Mechanism of Broadband Whoosh Noise in an Automotive Turbocharger Centrifugal Compressor

2021 ◽  
pp. 1-35
Author(s):  
Rick Dehner ◽  
Pranav Sriganesh ◽  
Ahmet Selamet ◽  
Keith Miazgowicz
Keyword(s):  
Centrifugal Compressor ◽  
Combustion Engine ◽  
Three Dimensional ◽  
Leading Edge ◽  
Broadband Noise ◽  
Rotor Blades ◽  
Generation Mechanism ◽  
Primary Concern ◽  
Frequency Range ◽  
Modal Decomposition

Abstract The present study focuses on the acoustics of a turbocharger centrifugal compressor from a spark-ignition internal combustion engine. Whoosh noise is typically the primary concern for this type of compressor, which is loosely characterized by broadband sound elevation in the 4 to 13 kHz range. To identify the generation mechanism of broadband whoosh noise, the present study combines three approaches: three-dimensional (3D) computational fluid dynamics (CFD) predictions, experiments, and modal decomposition of 3D CFD results. After establishing the accuracy of predictions, flow structures and time-resolved pressures are closely examined in the vicinity of the main blade leading edge. This reveals the presence of rotating instabilities that may interact with the rotor blades to generate noise. An azimuthal modal decomposition is performed on the predicted pressure field to determine the number of cells and the frequency content of these rotating instabilities. The strength of the rotating instabilities and the frequency range in which noise is generated as a consequence of the rotor-rotating instability interaction, is found to correspond well with the qualitative trend of the whoosh noise that is measured several duct diameters upstream of the rotor blades. The variation of whoosh frequency range between low and high rotational speeds is interpreted through this analysis. It is also found that the whoosh noise primarily propagates along the duct as acoustic azimuthal modes. Hence, the inlet duct diameter, which governs the cut-off frequency for multi-dimensional acoustic modes, determines the lower frequency bound of the broadband noise.

Investigation on hydrodynamic forces leading to coarse particle entrainment using Large-Eddy Simulations

2021 ◽  
Author(s):  
Gaston Latessa ◽  
Angela Busse ◽  
Manousos Valyrakis
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Large Scale ◽  
Large Eddy Simulations ◽  
Flow Conditions ◽  
Mean Flow ◽  
Protection Measures ◽  
Practical Applications ◽  
Particle Entrainment ◽  
Large Eddy

<p>The prediction of particle motion in a fluid flow environment presents several challenges from the quantification of the forces exerted by the fluid onto the solids -normally with fluctuating behaviour due to turbulence- and the definition of the potential particle entrainment from these actions. An accurate description of these phenomena has many practical applications in local scour definition and to the design of protection measures.</p><p>In the present work, the actions of different flow conditions on sediment particles is investigated with the aim to translate these effects into particle entrainment identification through analytical solid dynamic equations.</p><p>Large Eddy Simulations (LES) are an increasingly practical tool that provide an accurate representation of both the mean flow field and the large-scale turbulent fluctuations. For the present case, the forces exerted by the flow are integrated over the surface of a stationary particle in the streamwise (drag) and vertical (lift) directions, together with the torques around the particle’s centre of mass. These forces are validated against experimental data under the same bed and flow conditions.</p><p>The forces are then compared against threshold values, obtained through theoretical equations of simple motions such as rolling without sliding. Thus, the frequency of entrainment is related to the different flow conditions in good agreement with results from experimental sediment entrainment research.</p><p>A thorough monitoring of the velocity flow field on several locations is carried out to determine the relationships between velocity time series at several locations around the particle and the forces acting on its surface. These results a relevant to determine ideal locations for flow investigation both in numerical and physical experiments.</p><p>Through numerical experiments, a large number of flow conditions were simulated obtaining a full set of actions over a fixed particle sitting on a smooth bed. These actions were translated into potential particle entrainment events and validated against experimental data. Future work will present the coupling of these LES models with Discrete Element Method (DEM) models to verify the entrainment phenomena entirely from a numerical perspective.</p>

High-Fidelity Simulations of a High-Pressure Turbine Stage: Effects of Reynolds Number and Inlet Turbulence

2021 ◽  
Author(s):  
Yaomin Zhao ◽  
Richard D. Sandberg
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Suction Side ◽  
Rotor Blades ◽  
High Fidelity ◽  
Mean Flow ◽  
High Pressure Turbine ◽  
Flow Shear ◽  
Phase Lock ◽  
The Mean

Abstract We present the first wall-resolved high-fidelity simulations of high-pressure turbine (HPT) stages at engine-relevant conditions. A series of cases have been performed to investigate the effects of varying Reynolds numbers and inlet turbulence on the aerothermal behavior of the stage. While all of the cases have similar mean pressure distribution, the cases with higher Reynolds number show larger amplitude wall shear stress and enhanced heat fluxes around the vane and rotor blades. Moreover, higher-amplitude turbulence fluctuations at the inlet enhance heat transfer on the pressure-side and induce early transition on the suction-side of the vane, although the rotor blade boundary layers are not significantly affected. In addition to the time-averaged results, phase-lock averaged statistics are also collected to characterize the evolution of the stator wakes in the rotor passages. It is shown that the stretching and deformation of the stator wakes is dominated by the mean flow shear, and their interactions with the rotor blades can significantly intensify the heat transfer on the suction side. For the first time, the recently proposed entropy analysis has been applied to phase-lock averaged flow fields, which enables a quantitative characterization of the different mechanisms responsible for the unsteady losses of the stages. The results indicate that the losses related to the evolution of the stator wakes is mainly caused by the turbulence production, i.e. the direct interaction between the wake fluctuations and the mean flow shear through the rotor passages.

Degradation of Aerodynamic Performance of an Intermediate-Pressure Steam Turbine Due to Erosion of Nozzle Guide Vanes and Rotor Blades

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Koichi Yonezawa ◽  
Tomoki Kagayama ◽  
Masahiro Takayasu ◽  
Genki Nakai ◽  
Kazuyasu Sugiyama ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Steam Turbine ◽  
Rotor Blade ◽  
Rotor Blades ◽  
Flow Angle ◽  
Guide Vanes ◽  
Intermediate Pressure ◽  
Pressure Steam ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Deteriorations of nozzle guide vanes (NGVs) and rotor blades of a steam turbine through a long-time operation usually decrease a thermal efficiency and a power output of the turbine. In this study, influences of blade deformations due to erosion are discussed. Experiments were carried out in order to validate numerical simulations using a commercial software ANSYS-cfx. The numerical results showed acceptable agreements with experimental results. Variation of flow characteristics in the first stage of the intermediate pressure steam turbine is examined using numerical simulations. Geometries of the NGVs and the rotor blades are measured using a 3D scanner during an overhaul. The old NGVs and the rotor blades, which were used in operation, were eroded through the operation. The erosion of the NGVs leaded to increase of the throat area of the nozzle. The numerical results showed that rotor inlet velocity through the old NGVs became smaller and the flow angle of attack to the rotor blade leading edge became smaller. Consequently, the rotor power decreased significantly. Influences of the flow angle of at the rotor inlet were examined by parametric calculations and results showed that the angle of attack was an important parameter to determine the rotor performance. In addition, the influence of the deformation of the rotor blade was examined. The results showed that the degradation of the rotor performance decreased in accordance with the decrease of blade surface area.

The Effect of Stage-Diffuser Interaction on the Aerodynamic Performance and Design of LP Steam Turbine Exhaust Systems

2018 ◽  
Author(s):  
Bowen Ding ◽  
Liping Xu ◽  
Jiandao Yang ◽  
Rui Yang ◽  
Yuejin Dai
Keyword(s):  
Steam Turbine ◽  
Renewable Energy Sources ◽  
Rotor Blades ◽  
Steam Turbines ◽  
Flow Conditions ◽  
Part Load ◽  
Last Stage ◽  
Load Conditions ◽  
Turbine Exhaust ◽  
Exhaust Systems

Modern large steam turbines for power generation are required to operate much more flexibly than ever before, due to the increasing use of intermittent renewable energy sources such as solar and wind. This has posed great challenges to the design of LP steam turbine exhaust systems, which are critical to recovering the leaving energy that is otherwise lost. In previous studies, the design had been focused on the exhaust diffuser with or without the collector. Although the interaction between the last stage and the exhaust hood has been identified for a long time, little attention has been paid to the last stage blading in the exhaust system’s design process, when the machine frequently operates at part-load conditions. This study focuses on the design of LP exhaust systems considering both the last stage and the exhaust diffuser, over a wide operating range. A 1/10th scale air test rig was built to validate the CFD tool for flow conditions representative of an actual machine at part-load conditions, characterised by highly swirling flows entering the diffuser. A numerical parametric study was performed to investigate the effect of both the diffuser geometry variation and restaggering the last stage rotor blades. Restaggering the rotor blades was found to be an effective way to control the level of leaving energy, as well as the flow conditions at the diffuser inlet, which influence the diffuser’s capability to recover the leaving energy. The benefits from diffuser resizing and rotor blade restaggering were shown to be relatively independent of each other, which suggests the two components can be designed separately. Last, the potentials of performance improvement by considering both the last stage rotor restaggering and the diffuser resizing were demonstrated by an exemplary design, which predicted an increase in the last stage power output of at least 1.5% for a typical 1000MW plant that mostly operates at part-load conditions.

Fluctuating boundary layer on a magnetized plate

1967 ◽  
Vol 63 (2) ◽  
pp. 513-525 ◽  
Author(s):  
Sahib Singh Chawla
Keyword(s):  
Boundary Layer ◽  
Low Frequency ◽  
Surface Current ◽  
Frequency Range ◽  
Mean Flow ◽  
Wave Type ◽  
High Frequencies ◽  
Phase Lead ◽  
The Mean ◽  
The Magnetic Field

The laminar boundary layer on a magnetized plate, when the magnetic field oscillates in magnitude about a constant non-zero mean, is analysed. For low-frequency fluctuations the solution is obtained by a series expansion in terms of a frequency parameter, while for high frequencies the flow pattern is of the ‘skin-wave’ type unaffected by the mean flow. In the low-frequency range, the phase lead and the amplitude of the skin-friction oscillations increase at first and then decrease to their respective ‘skin-wave’ values. On the other hand the phase angle of the surface current decreases from 90° to 45° and its amplitude increases with frequency.

Laminar Swirling Pipe Flow

1954 ◽  
Vol 21 (1) ◽  
pp. 1-7
Author(s):  
L. Talbot
Keyword(s):  
Swirling Flow ◽  
Nonlinear Effects ◽  
Critical Conditions ◽  
Flow Conditions ◽  
Rotationally Symmetric ◽  
Rate Of Decay ◽  
Linearized Theory ◽  
The Stability ◽  
Experimental Values ◽  
Rates Of Decay

Abstract The problem of the decay of a rotationally symmetric steady swirl superimposed on Poiseuille flow in a round pipe was investigated theoretically and experimentally. The object was to determine the degree to which the rate of decay of the swirl as predicted by a linearized theory agreed with measured rates of decay at flow conditions near the critical conditions for swirl instability. The solution to the linearized equation of motion for the swirl was obtained. Swirling flow was produced experimentally by rotating a section of the test pipe. Swirl velocities were determined from motion-picture studies of colored oil droplets introduced in the flow. The stability of the swirl was investigated through visualization of a dye filament, and a critical curve for swirl instability was determined experimentally relating the angular velocity of the rotating section to the Reynolds number. The theoretical and experimental values for the decay parameter were found to agree closely, even at conditions of flow near the critical conditions for instability. It was concluded that in the problem under consideration the nonlinear effects are not appreciable for stable decay of the swirl.

Sign in / Sign up

Export Citation Format

Share Document