Attribute analyses of acoustic emissions in hydraulic fracturing

2021 ◽  
pp. 1-43
Author(s):  
Juan Camilo Acosta ◽  
Son T. Dang ◽  
Carl H. Sondergeld ◽  
Chandra S. Rai
Keyword(s):  
Hydraulic Fracturing ◽  
Acoustic Waves ◽  
Failure Modes ◽  
Acoustic Emissions ◽  
Fracture Initiation ◽  
Horizontal Stress ◽  
Cylindrical Sample ◽  
Variable Rate ◽  
Horizontal Drilling ◽  
Injection Test

Hydraulic fracturing (HF) and horizontal drilling are essential to the development of shale gas and oil. Production depends on the stimulation success. During fracture initiation, propagation, and closure, cracks emit acoustic waves; these can be monitored in real time as microseismics in the field and as acoustic emissions (AEs) in the laboratory. AEs are the laboratory equivalent of field-scale microseismics and contain detailed information about HF fracture mechanics. The number of acoustic events correlates with the number of induced fractures and hence the stimulation volume. Three HF protocols under dry conditions were carried out on Tennessee sandstone: (1) a constant injection rate, (2) a precyclic injection, and (3) a variable-rate injection test. All three tests were performed under the same principal stress conditions: vertical stress of 10.3 MPa (1500 psi), minimum horizontal stress of 3.5 MPa (500 psi), and maximum horizontal stress of 20.7 MPa (3000 psi). In total, 16 piezoelectric transducers were mounted around a cylindrical sample to record the AEs. We have performed postsignal processing to extract AE event attributes, including the amplitudes, signal-to-noise ratio, arrival time, event location (with the velocity-anisotropy input), and frequency analyses. The AE events associated with the constant-rate injection test possessed the lowest frequencies (150–270 kHz). The variable-rate test AE events possessed higher frequencies (160–310 kHz), whereas the precyclic injection had events with the highest frequencies, peaking at 330 kHz. Acoustic events before failure had lower amplitudes, but higher frequency compared to those recorded postbreakdown, suggesting different failure modes. Precyclic injection induced the greatest number of locatable events before and after failure.

scholarly journals Rupture Directivity in 3D Inferred From Acoustic Emissions Events in a Mine-Scale Hydraulic Fracturing Experiment

2021 ◽  
Vol 9 ◽  
Author(s):  
José Ángel López-Comino ◽  
Simone Cesca ◽  
Peter Niemz ◽  
Torsten Dahm ◽  
Arno Zang
Keyword(s):  
Hydraulic Fracturing ◽  
Acoustic Emissions ◽  
Local Stress ◽  
Horizontal Stress ◽  
Monitoring Networks ◽  
Rupture Directivity ◽  
Shallow Subsurface ◽  
Minimum Horizontal Stress ◽  
Directivity Effects ◽  
Full Waveforms

Rupture directivity, implying a predominant earthquake rupture propagation direction, is typically inferred upon the identification of 2D azimuthal patterns of seismic observations for weak to large earthquakes using surface-monitoring networks. However, the recent increase of 3D monitoring networks deployed in the shallow subsurface and underground laboratories toward the monitoring of microseismicity allows to extend the directivity analysis to 3D modeling, beyond the usual range of magnitudes. The high-quality full waveforms recorded for the largest, decimeter-scale acoustic emission (AE) events during a meter-scale hydraulic fracturing experiment in granites at ∼410 m depth allow us to resolve the apparent durations observed at each AE sensor to analyze 3D-directivity effects. Unilateral and (asymmetric) bilateral ruptures are then characterized by the introduction of a parameter κ, representing the angle between the directivity vector and the station vector. While the cloud of AE activity indicates the planes of the hydrofractures, the resolved directivity vectors show off-plane orientations, indicating that rupture planes of microfractures on a scale of centimeters have different geometries. Our results reveal a general alignment of the rupture directivity with the orientation of the minimum horizontal stress, implying that not only the slip direction but also the fracture growth produced by the fluid injections is controlled by the local stress conditions.

Numerical Simulation and Laboratory Experiments of Hydraulic Fracturing of Highly Deviated Well

2013 ◽  
Vol 275-277 ◽  
pp. 278-281 ◽  
Author(s):  
Hai Yan Zhu ◽  
Jing Gen Deng ◽  
Song Yang Li ◽  
Zi Jian Chen ◽  
Wei Yan ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Hydraulic Fracturing ◽  
Fracture Initiation ◽  
Element Model ◽  
Simulation Method ◽  
Horizontal Stress ◽  
Initiation Point ◽  
Strength Failure ◽  
Fluid Penetration ◽  
Maximum Horizontal Stress

Considering the combined action of the fluid penetration and the casing, the seepage coupled deformation finite element model of the highly deviated casing perforation well is established by using the tensile strength failure criterion and applied on the BZ25-1 oil filed. The results show that the increasing of the perforation angle and the well azimuth and the decreasing of the inclination would lead to a higher fracture initiation pressure. The fracture initiation point always locates on the wellbore face when the influence of the casing is considered. When the casing is ignored: when the perforation angle is 0°-45°, the fracture initiation point locates on the root of the tunnel; when the angle is 45°-90°, the fracture initiation point may be on the wellbore face or the perforation biased toward the maximum horizontal stress direction; when the angle is near to 90°, the hydraulic fracturing difficultly fractures the rock through the perforation tunnels. The laboratory hydraulic fracturing simulation experiments of 45° deviated well are carried through 400mm3 cement specimen so as to obtain the fracture initiation point and geometric shape under different perforation angles, the results verify the accuracy of the numerical simulation method.

Design of Horizontal Wellbore in Dadas Shales of Turkey by Considering Wellbore Stability and Reservoir Geomechanics

2021 ◽  
Author(s):  
Sukru Merey ◽  
Can Polat ◽  
Tuna Eren
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Well ◽  
Oil And Gas ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Wellbore Stability ◽  
Horizontal Drilling ◽  
Horizontal Wellbore ◽  
Reservoir Geomechanics ◽  
Maximum Horizontal Stress

Abstract Currently, many horizontal wells are being drilled in Dadas shales of Turkey. Dadas shales have both oil (mostly) and gas potentials. Thus, hydraulic fracturing operations are being held to mobilize hydrocarbons. Up to 1000 m length horizontal wells are drilled for this purpose. However, there is not any study analyzing wellbore stability and reservoir geomechanics in the conditions of Dadas shales. In this study, the directions of horizontal wells, wellbore stability and reservoir geomechanics of Dadas shales were designed by using well log data. In this study, the python code developed by using Kirsch equations was developed. With this python code, it is possible to estimate unconfined compressive strength in along wellbore at different deviations. By analyzing caliper log, density and porosity logs of Dadas shales, vertical stress of Dadas shales was estimated and stress polygon for these shale was prepared in this study. Then, optimum direction of horizontal well was suggested to avoid any wellbore stability problems. According to the results of this study, high stresses are seen in horizontal directions. In this study, it was found that the maximum horizontal stress in almost the direction of North-South. The results of this study revealed that direction of maximum horizontal stress and horizontal well direction fluid affect the wellbore stability significantly. Thus, in this study, better horizontal well design was made for Dadas shales. Currently, Dadas shales are popular in Turkey because of its oil and gas potential so horizontal drilling and hydraulic fracturing operations are being held. However, in literature, there is no study about horizontal wellbore designs for Dadas shales. This study will be novel and provide information about the horizontal drilling design of Dadas shales.

scholarly journals Shale Reservoir-Centric Completions

2016 ◽  
Vol 9 (1) ◽  
pp. 92-106
Author(s):  
John S. Spaid ◽  
Jeff A. Dahl ◽  
Ronald G. Dusterhoft ◽  
Shameem Siddiqui ◽  
Eric Holderby ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Fracture Initiation ◽  
High Rate ◽  
Treatment Schedule ◽  
Statistical Process ◽  
Horizontal Drilling ◽  
Reservoir Performance ◽  
Multi Stage ◽  
Incremental Improvement ◽  
Shale Reservoir

In North America, the transition from more conventional reservoirs into tight, basin-centered gas and now source shales has caused the industry to change the way reservoir performance is being assessed, measured, and documented. Historically in conventional reservoirs the reservoir quality was carefully examined on a well by well basis to determine reserves in place and exploitation plans. For unconventional reservoirs, however, the commercializing of such plays quickly became centered on horizontal drilling of long laterals combined with massive volume, high rate multi-stage hydraulic fracturing. In that environment, completion design and hydraulic fracturing have become more of a statistical process; additionally, incremental improvement and innovation are used to create a treatment schedule often replicated across an entire field without consideration of reservoir variability across a lateral. Based upon vertical well experience, the fracture initiation points can be carefully selected by identifying the locations within the well that are best to perforate. In a horizontal well, however, the location of the lateral defines the fracture initiation points anywhere along the well, so the stratigraphic location of the well lateral becomes critical in non-homogeneous shale plays. To address this, engineers and geoscientists can identify important parameters necessary for optimum completion design, and earth modelling can then be used as a tool to capture and model these properties across the asset making critical information available as needed for drilling, completion, and production operations.

Shale, Quakes, and High Stakes: Regulating Fracking-Induced Seismicity in Oklahoma, USA and Lancashire, UK

2019 ◽  
Vol 3 (1) ◽  
pp. 1-14
Author(s):  
Miriam R. Aczel ◽  
Karen E. Makuch
Keyword(s):  
United States ◽  
Hydraulic Fracturing ◽  
Shale Gas ◽  
Seismic Activity ◽  
Oil And Gas ◽  
Oil And Gas Industry ◽  
High Volume ◽  
The United States ◽  
Horizontal Drilling ◽  
Induced Seismic Activity

High-volume hydraulic fracturing combined with horizontal drilling has “revolutionized” the United States’ oil and gas industry by allowing extraction of previously inaccessible oil and gas trapped in shale rock [1]. Although the United States has extracted shale gas in different states for several decades, the United Kingdom is in the early stages of developing its domestic shale gas resources, in the hopes of replicating the United States’ commercial success with the technologies [2, 3]. However, the extraction of shale gas using hydraulic fracturing and horizontal drilling poses potential risks to the environment and natural resources, human health, and communities and local livelihoods. Risks include contamination of water resources, air pollution, and induced seismic activity near shale gas operation sites. This paper examines the regulation of potential induced seismic activity in Oklahoma, USA, and Lancashire, UK, and concludes with recommendations for strengthening these protections.

scholarly journals An Extension Strain Type Mohr–Coulomb Criterion

2021 ◽  
Author(s):  
Manfred Staat
Keyword(s):  
Failure Modes ◽  
Peak Stress ◽  
Fracture Initiation ◽  
Failure Surface ◽  
Confining Pressure ◽  
Biaxial Compression ◽  
Simple Extension ◽  
Strain Criterion ◽  
Shear Component ◽  
Extension Strain

AbstractExtension fractures are typical for the deformation under low or no confining pressure. They can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. In this article, it is shown that the simple extension strain criterion makes unrealistic strength predictions in biaxial compression and tension. To overcome this major limitation, a new extension strain criterion is proposed by adding a weighted principal shear component to the simple criterion. The shear weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting extension failure modes, which are unexpected in the classical understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain leading to dilatancy. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak stress CP. Different from compressive loading, tensile loading requires only a limited number of critical cracks to cause failure. Therefore, for tensile stresses, the failure criteria must be modified somehow, possibly by a cut-off corresponding to the CI stress. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion.

scholarly journals A Review of Hydraulic Fracturing Simulation

2021 ◽  
Author(s):  
Bin Chen ◽  
Beatriz Ramos Barboza ◽  
Yanan Sun ◽  
Jie Bai ◽  
Hywel R Thomas ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
State Of The Art ◽  
Numerical Models ◽  
Gas Production ◽  
Physical Processes ◽  
Horizontal Drilling ◽  
Improve Treatment ◽  
Multi Stage ◽  
Pros And Cons ◽  
Treatment Designs

AbstractAlong with horizontal drilling techniques, multi-stage hydraulic fracturing has improved shale gas production significantly in past decades. In order to understand the mechanism of hydraulic fracturing and improve treatment designs, it is critical to conduct modelling to predict stimulated fractures. In this paper, related physical processes in hydraulic fracturing are firstly discussed and their effects on hydraulic fracturing processes are analysed. Then historical and state of the art numerical models for hydraulic fracturing are reviewed, to highlight the pros and cons of different numerical methods. Next, commercially available software for hydraulic fracturing design are discussed and key features are summarised. Finally, we draw conclusions from the previous discussions in relation to physics, method and applications and provide recommendations for further research.

Predicting the azimuth of natural fractures and in-situ horizontal stress: A case study from Sichuan Basin, China

Geophysics ◽  
2021 ◽  
pp. 1-97
Author(s):  
kai lin ◽  
Bo Zhang ◽  
Jianjun Zhang ◽  
Huijing Fang ◽  
Kefeng Xi ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Sichuan Basin ◽  
Horizontal Stress ◽  
Seismic Attributes ◽  
Seismic Events ◽  
Natural Fractures ◽  
Microseismic Data ◽  
Maximum Horizontal Stress

The azimuth of fractures and in-situ horizontal stress are important factors in planning horizontal wells and hydraulic fracturing for unconventional resources plays. The azimuth of natural fractures can be directly obtained by analyzing image logs. The azimuth of the maximum horizontal stress σH can be predicted by analyzing the induced fractures on image logs. The clustering of micro-seismic events can also be used to predict the azimuth of in-situ maximum horizontal stress. However, the azimuth of natural fractures and the in-situ maximum horizontal stress obtained from both image logs and micro-seismic events are limited to the wellbore locations. Wide azimuth seismic data provides an alternative way to predict the azimuth of natural fractures and maximum in-situ horizontal stress if the seismic attributes are properly calibrated with interpretations from well logs and microseismic data. To predict the azimuth of natural fractures and in-situ maximum horizontal stress, we focus our analysis on correlating the seismic attributes computed from pre-stack and post-stack seismic data with the interpreted azimuth obtained from image logs and microseismic data. The application indicates that the strike of the most positive principal curvature k1 can be used as an indicator for the azimuth of natural fractures within our study area. The azimuthal anisotropy of the dominant frequency component if offset vector title (OVT) seismic data can be used to predict the azimuth of maximum in-situ horizontal stress within our study area that is located the southern region of the Sichuan Basin, China. The predicted azimuths provide important information for the following well planning and hydraulic fracturing.

Sign in / Sign up

Export Citation Format

Share Document