Seismic Rehabilitation of Reinforced Concrete Beam-Column Connections

1996 ◽  
Vol 12 (4) ◽  
pp. 761-780 ◽  
Author(s):  
A. Ghobarah ◽  
Tarek S. Aziz ◽  
Ashraf Biddah
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Load ◽  
Concrete Structures ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Experimental Program ◽  
Reinforced Concrete Structures ◽  
Test Results ◽  
Seismic Rehabilitation ◽  
Existing Structures

As building codes are updated, some of the existing important structures may fall short of complying with current standards even though they may have been properly designed and constructed according to earlier codes. Many existing structures may be inadequate and may pose severe risk during seismic events. Rehabilitation measures to upgrade the capacity of these structures can be performed at some point in their useful lives especially when located in seismically active zones. A new method for improving the seismic performance of existing reinforced concrete structures is by jacketing the deficient connections using corrugated steel jackets. An experimental program was conducted to evaluate this method of rehabilitation. Corrugated steel jacketing addresses the particular weakness that is often found in existing reinforced concrete structures, namely the lack of sufficient shear reinforcement and the required confining reinforcement within the joints and in adjoining beams and columns. The performance of four reinforced concrete connections was determined experimentally. The test specimens include one connection representing existing structures, one designed according to current seismic codes and two rehabilitated connections. The test results showed satisfactory performance at high cyclic load levels and significant increase in the shear capacity and ductility of connections rehabilitated with corrugated steel jackets.

Seismic Rehabilitation of Beam-Column Joints Using FRP Sheets and Buckling Restrained Braces

2013 ◽  
Vol 479-480 ◽  
pp. 1170-1174
Author(s):  
Hee Cheul Kim ◽  
Dae Jin Kim ◽  
Min Sook Kim ◽  
Young Hak Lee
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Seismic Performance ◽  
Reinforced Concrete Structures ◽  
Test Results ◽  
Seismic Rehabilitation ◽  
Buckling Restrained Braces ◽  
Column Joint ◽  
Energy Dissipation Capacity

The purpose of this study was to evaluate seismic performance of rehabilitated beam-column joint using FRP sheets and Buckling Restrained Braces (BRBs) and provide test data related to rehabilitated beam-column joints in reinforced concrete structures. The seismic performance of total six beam-column specimens is evaluated under cyclic loadings in terms of shear strength, effective stiffness, energy dissipation and ductility. The test results showed wrapping FRP sheets can contribute to increase the effect of confinement and the crack delay. Also retrofitting buckling restrained braces (BRBs) can improve the stiffness and energy dissipation capacity. Both FRP sheets and BRBs can effectively improve the strength, stiffness and ductility of seismically deficient beam-column joints.

Study on Seismic Behavior of Vertical Connection in Prefabricated Reinforced Concrete Structures

2011 ◽  
Vol 250-253 ◽  
pp. 1385-1394
Author(s):  
Guo Hua Song ◽  
Dong Wei Wang ◽  
Bing Kang Liu
Keyword(s):  
Reinforced Concrete ◽  
Seismic Behavior ◽  
Concrete Structures ◽  
Shear Resistance ◽  
Repeated Loading ◽  
Reinforced Concrete Structures ◽  
Test Results ◽  
Dowel Action ◽  
Cycle Loading ◽  
Good Agreement

The paper attempts to research the seismic behavior and mechanical mechanisms under repeated low-cycle loading of vertical connections in prefabricated reinforced concrete structures. Eighteen specimens were designed and tested, the test process and the mechanical mechanisms are studied, the seismic behavior of connections is analyzed, and the shear resistance formulas are proposed. The theoretical values based on proposed formulas are good agreement with test results. Under repeated loading, the shear resistance decreases, the connection ductility increases with connecting bar, but decreases with connection width. However, all the connections fail crisply with poor ductility. At sudden-cracking, the shear resistance increases with connecting bar, but changes nonlinearly with connection width. The resistance is composed of attributions of mechanism of diagonal-compressive column (MDCC) and mechanism of compressive friction action (MCFA). After sudden-cracking, the shear resistance is provided by weakened MDCC and dowel action of connecting bars (DACB). It increases with connecting bar and connection width.

Seismic response of reinforced concrete frame subassemblages — a Canadian code perspective

1989 ◽  
Vol 16 (5) ◽  
pp. 627-649 ◽  
Author(s):  
Patrick Paultre ◽  
Daniel Castele ◽  
Suzanne Rattray ◽  
Denis Mitchell
Keyword(s):  
Reinforced Concrete ◽  
Seismic Design ◽  
Concrete Structures ◽  
Poor Performance ◽  
Reinforced Concrete Beam ◽  
Test Results ◽  
Reinforced Concrete Frame ◽  
Concrete Frame ◽  
Slab Width ◽  
Cyclic Loading Tests

The 1984 CSA standard for the design of concrete structures for buildings provided new seismic design and detailing requirements for concrete structures. Full-scale, reversed cyclic loading tests of reinforced concrete beam–slab–column subassemblages were carried out to investigate the seismic performance of frame structures designed with the latest Canadian code. The test results indicate the importance of including the influence of slab reinforcement in computing the beam capacity as well as the need to carefully design the joint regions for shear. The test results indicate the excellent performance of frame components designed with K = 0.7 (R = 4.0) and the poor performance of those designed and detailed with K = 2.0 (R = 1.5). The performance of subassemblages designed with K = 1.3 (R = 2.0) depends on the column to beam strength ratio and on the shear strength of the joints. Models to predict the flexural response as well as the shear response of key elements are described and the role of the spandrel beam in limiting the effective slab width is explained. Key words: seismic design, reinforced concrete, detailing, structures, codes.

Experimental Evaluation of Corrosion Effect on Bond Between Steel and Concrete in Presence of Cyclic Action

2009 ◽  
Vol 417-418 ◽  
pp. 345-348 ◽  
Author(s):  
Luca Giordano ◽  
Giuseppe Mancini ◽  
Francesco Tondolo
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Load ◽  
Crack Opening ◽  
Concrete Structures ◽  
Electrochemical Corrosion ◽  
Reinforced Concrete Structures ◽  
Reinforcing Bars ◽  
Cyclic Action ◽  
In Series ◽  
Ultimate Condition

Corrosion modifies the steel-concrete interface in reinforced concrete structures. The efficiency of the connection between the two materials is reduced and the structural behavior both in service and in ultimate condition is affected. Moreover in structures subjected to cyclic load, a simultaneous mechanical deterioration due to the load is present. In this work an experimental analysis on reinforced concrete structures under both cyclic load and corrosion of reinforcing bars is presented. Three couples of reinforced concrete ties are connected in series and subjected to the same stress variation in order to produce the cracking conditions and to activate the bond mechanism. However, while one of the two reinforced concrete ties is only subjected to cyclic load, the second one is also corroded using an accelerated electrochemical corrosion process. The simultaneous effect of the cyclic load and corrosion is evaluated monitoring the crack opening on the structures during the test and by means of visual inspection of the sample. The test results show the correlation between the mechanism of bond and the average level of stresses for an amplified stress range.

scholarly journals Optimization of reinforced concrete structures: importance of design detail level

2021 ◽  
Vol 263 ◽  
pp. 02002
Author(s):  
Ashot Tamrazyan ◽  
Anatoly Alekseytsev
Keyword(s):  
Reinforced Concrete ◽  
Cost Minimization ◽  
Concrete Structures ◽  
Reinforced Concrete Beam ◽  
Normal Operation ◽  
Design Solution ◽  
Reinforced Concrete Structures ◽  
Variable Parameters ◽  
Design Detail ◽  
The Cost

The study of the influence for design solution detailing on the cost of reinforced concrete structures during their optimization is carried out. A hypothesis is formulated on the final improvement of the target criterion with an increase in the number of variable parameters. Depending on this number, the concepts of three levels of detail are introduced, at which optimization can be carried out, and the degree of risk of failure of the structure is indicated for them. Using the example of finding a constructive solution for a reinforced concrete beam by the cost minimization criterion, the relationship of the cost change is shown when the number of independently variable parameters changes. The normal operation of the beam and the emergency action effects in the form of local damage to a single corner connection are taken into account. Genetic algorithms are used for the optimization.

scholarly journals Crack Detection of Reinforced Concrete Structures Based on BOFDA and FBG Sensors

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Qinghua Zhang ◽  
Ziming Xiong
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Crack Detection ◽  
Concrete Structures ◽  
Lower Surface ◽  
Reinforced Concrete Beam ◽  
Sensor Data ◽  
Reinforced Concrete Structures ◽  
Surface Cracks ◽  
Fbg Sensors

Reinforced concrete structural elements, as an important component of buildings and structures, require inspection for the purposes of crack detection which is an important part of structural health monitoring. Now existing crack detection methods usually use a single technology and can only detect internal or external cracks. In this paper, the authors propose a new sensing system combining BOFDA (Brillouin optical frequency-domain analysis) and FBG (fiber Bragg grating) technology, which are used to detect internal and surface cracks and their development in reinforced concrete structures, and an attempt is made to estimate the width of surface cracks. In these experiments, a special reinforced concrete beam structure was designed by the author for crack detection under load. Four continuous distributed optical fibers are fixed on the steel skeleton, which is located within the reinforced concrete beam. Three FBG sensors are fixed on the lower surface of the beam, near its centre. By analysing the sensor data, it can be found that the BOFDA-distributed fiber can be used to detect internal cracking before surface cracking, and the difference between scans can be used to judge the time of onset of internal cracking, but the relative error in position is about 5%, while the FBG sensor can detect the cracking time of microcracks on the lower surface in near-real-time and can be used to calculate the crack width. Through the experiment, it is found that if the combination of BOFDA and FBG technology is adopted, we can initially use the strain data obtained by multiple groups of BOFDA monitoring to predict the general location of the internal cracks, then to monitor the exact location of the surface cracks by FBG in the medium term, and to estimate the width of the final expansion of the cracks finally.

scholarly journals The Mechanical Properties of Centrifuged Concrete in Reinforced Concrete Structures

2020 ◽  
Vol 10 (10) ◽  
pp. 3570
Author(s):  
Romualdas Kliukas ◽  
Ona Lukoševičienė ◽  
Arūnas Jaras ◽  
Bronius Jonaitis
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Concrete Strength ◽  
Concrete Structures ◽  
High Strength ◽  
Reinforcement Ratio ◽  
Transverse Reinforcement ◽  
Reinforced Concrete Structures ◽  
Test Results ◽  
Moduli Of Elasticity

This article explores the influence of transverse reinforcement (spiral) and high-strength longitudinal reinforcements on the physical-mechanical properties of centrifuged annular cross-section elements of concrete. The test results of almost 200 reinforced, and over 100 control elements are summarizing in this article. The longitudinal reinforcement ratio of samples produced in the laboratory and factory varied from 1.0% to 6.0%; the transverse reinforcement ratio varied from 0.25% to 1.25%; the pitch of spirals varied from 100 mm to 40 mm and the concrete strength varied from 25 MPa to 60 MPa. Experimental relationships of coefficients for concrete strength, moduli of elasticity and limits of the longitudinal strain of centrifuged concrete in reinforced concrete structures in short-term concentrically compression were proposed.

scholarly journals Experimental study of beams on yielding supports with thrust

2018 ◽  
Vol 143 ◽  
pp. 01016
Author(s):  
Oleg Kumpyak ◽  
Zaur Galyautdinov ◽  
Daud Galyautdinov
Keyword(s):  
Reinforced Concrete ◽  
Crack Resistance ◽  
Dynamic Loading ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Horizontal Displacement ◽  
Positive Outcome ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Structures ◽  
Short Term

The design of reinforced concrete structures which are subjected to static and intensive dynamic loading requires taking into account the occurrence of thrust reaction resulting in significant increase in strength and crack resistance. Application of yielding supports for the purpose of increasing the energy capacity of structures shall also be considered. The present research aims to define feasibility of yielding supports application in thrust structures. The paper presents the outcomes of experimental studies of reinforced concrete beam structures on yielding supports subjected to thrust under static and short-term dynamic loading. The influence of thrust on the strength, deformation property and crack resistance of reinforced concrete structures under static and short-term dynamic loading was investigated. The combined use of yielding supports and the restriction of horizontal displacement of the support contour were also considered in the study. Research results testify on the positive outcome when yielding supports are applied in the structures subjected to thrust.

THE INFLUENCE OF BASALT-COMPOSITE PRESTRESSED REINFORCEMENT ON THE OPERATION OF LOW-REINFORCED CONCRETE STRUCTURES WITH INTERBLOCK CONSTRUCTION JOINTS

2020 ◽  
pp. 50-59
Author(s):  
O.D. RUBIN ◽  
◽  
S.E. LISICHKIN ◽  
O.V. ZYUZINA
Keyword(s):  
Reinforced Concrete ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Bending Moment ◽  
Reinforced Concrete Beam ◽  
Hydraulic Structures ◽  
Reinforced Concrete Structures ◽  
Beam Type ◽  
Construction Joints ◽  
Composite Reinforcement

It is proposed to use prestressed basalt composite reinforcement to strengthen reinforced concrete structures of hydraulic structures. In order to substantiate technical reinforcement of reinforced concrete structures of hydraulic structures with prestressed basalt composite inforcement, experimental studies were carried out. For experimental studies, reinforced concrete beam-type structures with vertical interblock construction joints were adopted.The results of experimental studies of reinforced concrete models of beam type with interblock joints reinforced with prestressed basalt composite reinforcement by the method of tension “on concrete”are presented. The models are tested for bending moment and transverse force. A special character of cracking is noted; full restoration of the bearing capacity of reinforced concrete structures, weakened by interblock construction joints, was recorded due to the reinforcement of prestressed basalt composite reinforcement.

Sign in / Sign up

Export Citation Format

Share Document