Dynamics of Timoshenko Beams Conveying Fluid

1976 ◽  
Vol 18 (4) ◽  
pp. 210-220 ◽  
Author(s):  
M. P. Paidoussis ◽  
B. E. Laithier

The dynamics of pipes conveying fluid is described by means of the Timoshenko beam theory. The equations of motion are derived and solved ( a) by a finite-difference technique, and ( b) by a variational method. It is shown that the latter is the more efficient method. The eigenfrequencies of the system and its stability characteristics are compared with results obtained previously using the Euler-Bernoulli beam theory, and it is shown that in certain cases (e.g. short pipes) the two sets of results diverge. Experiments indicate that the present theory is more successful in predicting the observed behaviour. Furthermore, the present theory shows that, in some cases, cantilevered pipes may lose stability by buckling, whereas previous theories indicate that the system always loses stability by flutter.

Author(s):  
Pezhman A. Hassanpour ◽  
Kamran Behdinan

In this paper, the model of a micro-machined beam-type resonator is presented. The resonator is a micro-bridge which is modeled using Euler-Bernoulli beam theory. A comb-drive electrostatic actuator is attached to the micro-bridge for the excitation/detection of vibrations. In the models presented in the literature, it is assumed that the center of mass of the comb-drive is located on the neutral axis of the beam. In this paper, it is demonstrated that this assumption can not be applied for asymmetric-shaped comb-drives. Furthermore, the governing equations of motion are derived by relaxing the above assumption. It has been shown that the off-axis center of mass of the comb-drive generates an amplitude-dependent transverse force in the beam, which is essentially a nonlinear effect. The governing equations of motion are solved using a hybrid analytical-numerical approach. The end application of the structure under investigation is in resonant sensing and energy harvesting applications.


1974 ◽  
Vol 96 (2) ◽  
pp. 411-419 ◽  
Author(s):  
J. P. Sadler ◽  
G. N. Sandor

A method of kineto-elastodynamic analysis is developed employing lumped parameter models for simulating moving mechanism components subject to elastic bending vibrations. The mechanism analyzed is the general planar four-bar linkage and the analytical model includes the response coupling associated with both the transmission of forces at the pin joints and the dependence of the undeformed motion of a link on the elastic motion of other links. Nonlinear equations of motion are derived by way of Euler-Bernoulli beam theory, and numerical solution of these equations is illustrated for specific examples. The model is suitable for the analysis of mechanisms with non-periodic motion and with nonuniform cross-section members.


2013 ◽  
Vol 135 (6) ◽  
Author(s):  
Yan-Shin Shih ◽  
Chen-Yuan Chung

This paper investigates the dynamic response of the cracked and flexible connecting rod in a slider-crank mechanism. Using Euler–Bernoulli beam theory to model the connecting rod without a crack, the governing equation and boundary conditions of the rod's transverse vibration are derived through Hamilton's principle. The moving boundary constraint of the joint between the connecting rod and the slider is considered. After transforming variables and applying the Galerkin method, the governing equation without a crack is reduced to a time-dependent differential equation. After this, the stiffness without a crack is replaced by the stiffness with a crack in the equation. Then, the Runge–Kutta numerical method is applied to solve the transient amplitude of the cracked connecting rod. In addition, the breathing crack model is applied to discuss the behavior of vibration. The influence of cracks with different crack depths on natural frequencies and amplitudes is also discussed. The results of the proposed method agree with the experimental and numerical results available in the literature.


Author(s):  
Jiahao Zheng ◽  
Hongyuan Qiu ◽  
Jianming Yang ◽  
Stephen Butt

Based on linear damage accumulation law, this paper investigates the fatigue problem of drill-strings in time domain. Rainflow algorithms are developed to count the stress cycles. The stress within the drill-string is calculated with finite element models which is developed using Euler-Bernoulli beam theory. Both deterministic and random excitations to the drill-string system are taken into account. With this model, the stress time history in random nature at any location of the drill-string can be obtained by solving the random dynamic model of the drill-string. Then the random time history is analyzed using rainflow counting method. The fatigue life of the drill-string under both deterministic and random excitations can therefore be predicted.


Author(s):  
Wei-Jiun Su ◽  
Hsuan-Chen Lu

In this study, a dual-beam piezoelectric energy harvester is proposed. This harvester consists of a main beam and an auxiliary beam with a pair of magnets attached to couple their motions. The potential energy of the system is modeled to understand the influence of the potential wells on the dynamics of the harvester. It is noted that the alignment of the magnets significantly influences the potential wells. A theoretical model of the harvester is developed based on the Euler-Bernoulli beam theory. Frequency sweeps are conducted experimentally and numerically to study the dynamics of the harvester. It is shown that the dual-beam harvester can exhibit hardening effect with different configurations of magnet alignments in frequency sweeps. The performance of the harvester can be improved with proper placement of the magnets.


2015 ◽  
Vol 82 (9) ◽  
Author(s):  
X. Chen ◽  
S. A. Meguid

In this paper, we investigate the asymmetric bifurcation behavior of an initially curved nanobeam accounting for Lorentz and electrostatic forces. The beam model was developed in the framework of Euler–Bernoulli beam theory, and the surface effects at the nanoscale were taken into account in the model by including the surface elasticity and the residual surface tension. Based on the Galerkin decomposition method, the model was simplified as two degrees of freedom reduced order model, from which the symmetry breaking criterion was derived. The results of our work reveal the significant surface effects on the symmetry breaking criterion for the considered nanobeam.


1972 ◽  
Vol 9 (03) ◽  
pp. 333-344
Author(s):  
Finn C. Michelsen ◽  
Uilmann Kilgore

The problem has been treated of determining deflections and bending moments of the barge hull and independent cargo tanks combination as these occur in Class I and Class II barges during grounding. The method of solution is that of the initial parameters, which is here developed by means of operational calculus. The solution is closed and exact within the limitations of the Euler-Bernoulli beam theory.


Author(s):  
Vahid Mohamadhashemi ◽  
Amir Jalali ◽  
Habib Ahmadi

In this study, the nonlinear vibration of a curved carbon nanotube conveying fluid is analyzed. The nanotube is assumed to be covered by a piezoelectric layer and the Euler–Bernoulli beam theory is employed to establish the governing equations of motion. The influence of carbon nanotube curvature on structural modeling and fluid velocity vector is considered and the slip boundary conditions of CNT conveying fluid are included. The mathematical modeling of the structure is developed using Hamilton’s principle and then, the Galerkin procedure is employed to discretize the equation of motion. Furthermore, the frequency response of the system is extracted by applying the multiple scales method of perturbation. Finally, a comprehensive study is carried out on the primary resonance and piezoelectric-based parametric resonance of the system. It is shown that consideration of nanotube curvature may lead to an increase in nonlinearity. Implementing the fluid velocity vector in which nanotube curvature is included highly affects the maximum amplitude of the response and should not be ignored. Furthermore, different system parameters have evident impacts on the behavior of the system and therefore, selecting the reasonable geometrical and physical parameters of the system can be very useful to achieve a favorable response.


Author(s):  
Yichi Zhang ◽  
Bingen Yang

Abstract Vibration analysis of complex structures at medium frequencies plays an important role in automotive engineering. Flexible beam structures modeled by the classical Euler-Bernoulli beam theory have been widely used in many engineering problems. A kinematic hypothesis in the Euler-Bernoulli beam theory is that plane sections of a beam normal to its neutral axis remain normal when the beam experiences bending deformation, which neglects the shear deformation of the beam. However, as observed by researchers, the shear deformation of a beam component becomes noticeable in high-frequency vibrations. In this sense, the Timoshenko beam theory, which describes both bending deformation and shear deformation, may be more suitable for medium-frequency vibration analysis of beam structures. This paper presents an analytical method for medium-frequency vibration analysis of beam structures, with components modeled by the Timoshenko beam theory. The proposed method is developed based on the augmented Distributed Transfer Function Method (DTFM), which has been shown to be useful in various vibration problems. The proposed method models a Timoshenko beam structure by a spatial state-space formulation in the s-domain, without any discretization. With the state-space formulation, the frequency response of a beam structure, in any frequency region (from low to very high frequencies), can be obtained in an exact and analytical form. One advantage of the proposed method is that the local information of a beam structure, such as displacements, bending moment and shear force at any location, can be directly obtained from the space-state formulation, which otherwise would be very difficult with energy-based methods. The medium-frequency analysis by the augmented DTFM is validated with the FEA in numerical examples, where the efficiency and accuracy of the proposed method is present. Also, the effects of shear deformation on the dynamic behaviors of a beam structure at medium frequencies are illustrated through comparison of the Timoshenko beam theory and the Euler-Bernoulli beam theory.


2019 ◽  
Vol 19 (08) ◽  
pp. 1950093 ◽  
Author(s):  
W. H. Pan ◽  
C. M. Wang ◽  
H. Zhang

Presented herein is a matrix method for buckling analysis of general frames based on the Hencky bar-chain model comprising of rigid segments connected by hinges with elastic rotational springs. Unlike the conventional matrix method of structural analysis based on the Euler–Bernoulli beam theory, the Hencky bar-chain model (HBM) matrix method allows one to readily handle the localized changes in end restraint conditions or localized structural changes (such as local damage or local stiffening) by simply tweaking the spring stiffnesses. The developed HBM matrix method was applied to solve some illustrative example problems to demonstrate its versatility in solving the buckling problem of beams and frames with various boundary conditions and local changes. It is hoped that this easy-to-code HBM matrix method will be useful to engineers in solving frame buckling problems.


Sign in / Sign up

Export Citation Format

Share Document