The Application of Gas-Turbine Technique to Steam Power

1950 ◽  
Vol 162 (1) ◽  
pp. 209-238 ◽  
Author(s):  
J. F. Field
Keyword(s):  
High Temperature ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Power ◽  
Temperature Range ◽  
Power Stations ◽  
Lower Temperature Range ◽  
Lower Temperature ◽  
External Combustion ◽  
Steam Cycle

Early attempts to adapt the mechanism of the turbine to the air- or gas-engine were frustrated by the losses in the compressor, but in the last twenty years improvements in the efficiency of the latter, together with better high-temperature metals for the turbine, have enabled the gas turbine to approach the efficiency of the steam turbine. The gas turbine has to operate from a much higher temperature and with more effective high-temperature regeneration to achieve this. On the other hand it cannot utilize heat down to anything like the same lower temperature as steam power. Most regenerative gas-turbine cycles are therefore more efficient than the steam cycle at the upper temperature range, and less efficient at the lower temperature range. Now that the Rankine steam cycle has reached 1,000 deg. F., a given increment of temperature has much less effect on the steam turbine than on the gas turbine. The paper describes a condensing gas-turbine† cycle with external combustion, which utilizes orthodox gas-turbine and steam-turbine components in such a manner that the thermodynamic advantages of the two in the respective temperature ranges mentioned above are combined to give a higher thermal efficiency than either the steam or the gas turbine is capable of alone, and with the prospective ability to utilize almost any fuel. A great improvement may thus be made possible in the fuel economy of condensing steam power stations, steamship propulsion, and steam locomotives, and in the ratio of mechanical power to heat in combined power and process or district heat production. It may become commercially worth while, apart from the saving in coal, to eliminate a large proportion of condensing operation on land in the winter months. By integrating the fuel-using industries in this manner it should be possible to save at least fifty-million tons of coal per annum on the present aggregate output of power and heat, with a further saving of eleven-million tons of locomotive coal. This should enable the nation to afford much more liberal use of power and heat and thus achieve much greater production in transport and industry.

Start-Up Optimization of a CCGT Power Station Using Model Based Gas Turbine Control

2018 ◽  
Author(s):  
Alessandro Nannarone ◽  
Sikke A. Klein
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Optimization Model ◽  
Feedback Loop ◽  
Combined Cycle ◽  
Process Data ◽  
Power Station ◽  
Power Stations ◽  
Start Up ◽  
Steam Cycle

The rapid growth of renewable generation and its intermittent nature has modified the role of combined cycle power stations in the energy industry, and the key feature for the operational excellence is now flexibility. Especially, the capability to start an installation quickly and efficiently after a shutdown period leads to lower operational cost and a higher capacity factor. However, most of existing thermal power stations worldwide are designed for continuous operation, with no special focus on an efficient start-up process. In most current start-up procedures, the gas turbine controls ensure maximum heat flow to the heat recovery steam generator, without feedback from the steam cycle. The steam cycle start-up controls work independently with as main control parameter the limitation of the thermal stresses in the steam turbine rotor. In this paper, a novel start-up procedure of an existing combined cycle power station is presented, and it uses a feedback loop between the steam turbine, the boiler and the gas turbine start-up controls. This feedback loop ensures that the steam turbine can be started up with a significant reduction in stresses. To devise and assess this start-up methodology, a flexible and accurate dynamic model was implemented in the Simulink™ environment. It contains more than 100 component blocks (heat exchangers, valves, meters and sensors, turbines, controls, etc.), and the mathematical component sub-models are based on physical models and experimental correlations. This makes the model generally applicable to other power plant installations. The model was validated against process data related to the three start-up types (cold start, warm start, hot start). On this basis, the optimization model is implemented with feedback loops that control for example the exit temperature of the gas turbine based on the actual steam turbine housing temperature, resulting in a smoother heating up of the steam turbine. The optimization model was used to define the optimal inlet guide vanes position and gas turbine power output curves for the three types of start-up. These curves were used during real power station start-ups, leading to, for cold and warm starts, reductions in the start-up time of respectively 32.5% and 31.8%, and reductions in the fuel consumption of respectively 47.0% and 32.4%. A reduction of the thermal stress in the steam turbines is also achieved, thanks to the new start-up strategy.

FANSTEEL 291 METAL

Alloy Digest ◽  
1973 ◽  
Vol 22 (11) ◽  
Keyword(s):  
Fracture Toughness ◽  
High Temperature ◽  
Base Alloy ◽  
Weight Ratio ◽  
High Strength ◽  
Heat Treating ◽  
Temperature Range ◽  
Temperature Performance ◽  
Lower Temperature Range ◽  
Lower Temperature

Abstract FANSTEEL 291 METAL is a columbium-base alloy that can be readily fabricated, machined and welded. It is used in the high-temperature range 2800-3500 F where excellent strength-to-weight ratio can be used to advantage. It is also used in the lower temperature range 2000-2700 F because of its availability and fabricability which may be of more importance than high strength alone. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness and creep. It also includes information on high temperature performance and corrosion resistance as well as heat treating, machining, and joining. Filing Code: Cb-20. Producer or source: Fansteel Metallurgical Corporation.

Start-Up Optimization of a CCGT Power Station Using Model-Based Gas Turbine Control

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Alessandro Nannarone ◽  
Sikke A. Klein
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Optimization Model ◽  
Feedback Loop ◽  
Combined Cycle ◽  
Process Data ◽  
Power Station ◽  
Power Stations ◽  
Start Up ◽  
Steam Cycle

The rapid growth of renewable generation and its intermittent nature has modified the role of combined cycle power stations in the energy industry, and the key feature for the operational excellence is now flexibility. Especially, the capability to start an installation quickly and efficiently after a shutdown period leads to lower operational cost and a higher capacity factor. However, most of existing thermal power stations worldwide are designed for continuous operation, with no special focus on an efficient start-up process. In most current start-up procedures, the gas turbine controls ensure maximum heat flow to the heat recovery steam generator, without feedback from the steam cycle. The steam cycle start-up controls work independently with as main control parameter the limitation of the thermal stresses in the steam turbine rotor. In this paper, a novel start-up procedure of an existing combined cycle power station is presented, and it uses a feedback loop between the steam turbine, the boiler and the gas turbine start-up controls. This feedback loop ensures that the steam turbine can be started up with a significant reduction in stresses. To devise and assess this start-up methodology, a flexible and accurate dynamic model was implemented in the Simulink environment. It contains >100 component blocks (heat exchangers, valves, meters and sensors, turbines, controls, etc.), and the mathematical component submodels are based on physical models and experimental correlations. This makes the model generally applicable to other power plant installations. The model was validated against process data related to the three start-up types (cold start, warm start, hot start). On this basis, the optimization model is implemented with feedback loops that control, for example, the exit temperature of the gas turbine based on the actual steam turbine housing temperature, resulting in a smoother heating up of the steam turbine. The optimization model was used to define the optimal inlet guide vanes position and gas turbine power output curves for the three types of start-up. These curves were used during real power station start-ups, leading to, for cold and warm starts, reductions in the start-up time of, respectively, 32.5% and 31.8%, and reductions in the fuel consumption of, respectively, 47.0% and 32.4%. A reduction of the thermal stress in the steam turbines is also achieved, thanks to the new start-up strategy.

Formability and Process Conditions of Magnesium Alloy Sheets

2005 ◽  
Vol 488-489 ◽  
pp. 453-456 ◽  
Author(s):  
Shi Hong Zhang ◽  
Yong Chao Xu ◽  
G. Palumbo ◽  
S. Pinto ◽  
Luigi Tricarico ◽  
...  
Keyword(s):  
Deep Drawing ◽  
Tensile Tests ◽  
Process Conditions ◽  
Drawing Ratio ◽  
Temperature Range ◽  
Fine Grained ◽  
Axial Tensile ◽  
Die Surface ◽  
Lower Temperature Range ◽  
Lower Temperature

Comparing the formability with each other, extrusion and various rolling experiments were carried out to make fine-grained AZ31 Mg sheets, and uni-axial tensile tests were carried out at different strain rates and temperatures to investigate the effect of different variables. A warm deep drawing tool setup with heating elements, which were distributed under the die surface and inside the blank holder, was designed and manufactured, and deep drawing was performed. Extruded Mg alloy AZ31 sheets exhibit the best deep drawing ability when working in the temperature range 250-350°C. Extruded and rolled sheets of 0.8 mm thick were also deep drawn in the lower temperature range 105-170°C，showing good formability and reaching a Limit Drawing Ratio up to 2.6 at 170°C for rolled sheets. At last, a sheet cup 0.4 mm thick was deep drawn successfully at 170 °C.

Steam Turbine Driving Compressor for Gas-Steam Combined Cycle Power Plant

2009 ◽  
Author(s):  
Wancai Liu ◽  
Hui Zhang
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Combined Cycle ◽  
Thermodynamic Process ◽  
Combined Cycle Power Plant ◽  
Steam Cycle

Gas turbine is widely applied in power-generation field, especially combined gas-steam cycle. In this paper, the new scheme of steam turbine driving compressor is investigated aiming at the gas-steam combined cycle power plant. Under calculating the thermodynamic process, the new scheme is compared with the scheme of conventional gas-steam combined cycle, pointing its main merits and shortcomings. At the same time, two improved schemes of steam turbine driving compressor are discussed.

Effect of Microstructure and Zr Addition on the Crystallographic Orientation Relationships among Phases related to the Eutectoid Decomposition of Nb3Si in near Eutectic Nb-Si alloy

2004 ◽  
Vol 842 ◽  
Author(s):  
Seiji Miura ◽  
Kenji Ohkubo ◽  
Tetsuo Mohri
Keyword(s):  
Eutectic Alloy ◽  
Crystallographic Orientation ◽  
Eutectoid Decomposition ◽  
Orientation Relationships ◽  
Temperature Range ◽  
Zr Addition ◽  
Heat Treated ◽  
Lower Temperature Range ◽  
Lower Temperature ◽  
Nose Temperature

ABSTRACTThe authors have reported in the previous study that the sluggish decomposition of Nb3Si phase is effectively accelerated by Zr addition [1]. This is obvious at lower temperature range than the nose temperature of the TTT curve. In the present study a eutectic alloy containing 1.5 % of Zr was investigated. The crystallographic orientation relationships among phases, such as eutectic Nb and product phases formed by eutectoid decomposition of Nb3Si (eutectoid Nb and Nb5Si3phases) in the Zr-containing sample which was heat treated at 1300°C were investigated by FESEM/EBSD for further understanding of the decomposition process in alloy with a different microstructure.

scholarly journals Effect of Temperature, Pressure, and Chemical Composition on the Electrical Conductivity of Schist: Implications for Electrical Structures under the Tibetan Plateau

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 961 ◽  
Author(s):  
Wenqing Sun ◽  
Lidong Dai ◽  
Heping Li ◽  
Haiying Hu ◽  
Changcai Liu ◽  
...  
Keyword(s):  
Tibetan Plateau ◽  
High Pressures ◽  
High Conductivity ◽  
Effect Of Temperature ◽  
The Tibetan Plateau ◽  
Temperature Range ◽  
Electrical Conductivities ◽  
Conductivity Anomalies ◽  
Lower Temperature Range ◽  
Lower Temperature

The experimental study on the electrical conductivities of schists with various contents of alkali ions (CA = K2O + Na2O = 3.94, 5.17, and 5.78 wt.%) were performed at high temperatures (623–1073 K) and high pressures (0.5–2.5 GPa). Experimental results indicated that the conductivities of schist markedly increased with the rise of temperature. Pressure influence on the conductivities of schist was extremely weak at the entire range of experimental temperatures. Alkali ion content has a significant influence on the conductivities of the schist samples in a lower temperature range (623–773 K), and the influence gradually decreases with increasing temperature in a higher temperature range (823–1073 K). In addition, the activation enthalpies for the conductivities of three schist samples were fitted as being 44.16–61.44 kJ/mol. Based on the activation enthalpies and previous studies, impurity alkaline ions (K+ and Na+) were proposed as the charge carriers of schist. Furthermore, electrical conductivities of schist (10−3.5–10−1.5 S/m) were lower than those of high-conductivity layers under the Tibetan Plateau (10−1–100 S/m). It was implied that the presence of schist cannot cause the high-conductivity anomalies in the middle to lower crust beneath the Tibetan Plateau.

scholarly journals Characteristics of Coherent Optical Phonons in a Hexagonal YMnO3 Thin Film

2019 ◽  
Vol 9 (4) ◽  
pp. 704 ◽  
Author(s):  
Takayuki Hasegawa
Keyword(s):  
Thin Film ◽  
Optical Phonon ◽  
Laser Pulses ◽  
Generation Process ◽  
Neel Temperature ◽  
Optical Phonons ◽  
Néel Temperature ◽  
Temperature Range ◽  
Lower Temperature Range ◽  
Lower Temperature

This paper reviews our recent study on a coherent optical phonon in a hexagonal YMnO3 thin film together with related optical studies in hexagonal RMnO3 (R = Y, Lu, Ho) compounds. Coherent phonons have been observed in RMnO3 compounds by pump-probe spectroscopy with subpicosecond laser pulses, whereas the observation of coherent optical phonons was reported only in LuMnO3. Recently, we succeeded in the observation of the coherent optical phonon in a YMnO3 thin film. The generation process of the coherent optical phonon is assigned to a displacive mechanism, which is identical to that in LuMnO3. The coherent optical phonon is observed in the temperature range from 10 K to room temperature, while the oscillation intensity strongly decreases as the temperature increases to the Néel temperature of ~70 K from a lower temperature range. It is interesting that the temperature dependence is largely different from that in LuMnO3. We describe that the result can be qualitatively explained by the property of an isostructural transition around the Néel temperature in RMnO3 compounds. In addition, we briefly discuss ultrafast incoherent responses of excited electronic states from the viewpoint of the excitation photon energy of laser pulses.

scholarly journals Reheat and Regenerative Gas Turbines for Feed Water Repowering of Steam Power Plant

1995 ◽  
Author(s):  
G. Negri di Montenegro ◽  
M. Gambini ◽  
A. Peretto
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Flow Rate ◽  
Gas Turbines ◽  
Power Plants ◽  
Feed Water ◽  
Brayton Cycle ◽  
Energy Integration ◽  
Steam Power ◽  
Steam Power Plants

This study is concerned with the repowering of existing steam power plants (SPP) by gas turbine (GT) units. The energy integration between SPP and GT is analyzed taking into particular account the employment of simple and complex cycle gas turbines. With regard to this, three different gas turbine has been considered: simple Brayton cycle, regenerative cycle and reheat cycle. Each of these cycles has been considered for feed water repowering of three different existing steam power plants. Moreover, the energy integration between the above plants has been analyzed taking into account three different assumptions for the SPP off-design conditions. In particular it has been established to keep the nominal value for steam turbine power output or for steam flow-rate at the steam turbine inlet or, finally, for steam flow-rate in the condenser. The numerical analysis has been carried out by the employment of numerical models regarding SPP and GT, developed by the authors. These models have been here properly connected to evaluate the performance of the repowered plants. The results of the investigation have revealed the interest of considering the use of complex cycle gas turbines, especially reheat cycles, for the feed water repowering of steam power plants. It should be taken into account that these energy advantages are determined by a repowering solution, i.e. feed water repowering which, although it is attractive for its simplicity, do not generally allows, with Brayton cycle, a better exploitation of the energy system integration in comparison with other repowering solutions. Besides these energy considerations, an analysis on the effects induced by repowering in the working parameters of existing components is also explained.

Scanning UV microspectrophotometry as a tool to study the changes of lignin in hydrothermally modified wood

Holzforschung ◽  
2016 ◽  
Vol 70 (3) ◽  
pp. 215-221 ◽  
Author(s):  
Bruno Andersons ◽  
Guna Noldt ◽  
Gerald Koch ◽  
Ingeborga Andersone ◽  
Anete Meija-Feldmane ◽  
...  
Keyword(s):  
Cell Wall ◽  
Degradation Products ◽  
Middle Lamella ◽  
Temperature Range ◽  
Wood Protection ◽  
Lower Temperature Range ◽  
Lower Temperature ◽  
The One ◽  
S2 Layer ◽  
Uv Microspectrophotometry

Abstract Thermal modification (TM) of wood has occupied a relatively narrow but stable niche as an alternative for chemical wood protection. There are different technological solutions for TM and not all details of their effects on wood tissue have been understood. The one-stage hydrothermal modification (HTM) at elevated vapour pressure essentially changes the wood’s composition and structure. In the present paper, the changes in three hardwood lignins (alder, aspen, and birch) were observed within the cell wall by means of cellular UV microspectrophotometry. The lignin absorbances in the compound middle lamella (CML) of unmodified wood are 1.7- to 2.0-fold higher than those in the fibre S2 layer. The woods were modified in the temperature range from 140 to 180°C, while in the lower temperature range (140°C/1 h), the UV absorbances are little affected. Essential changes occur in the range of 160–180°C and the UV data reflect these by absorbtion changes, while the absorbances at 278 nm rise with factors around 2 more in the S2 layer than in the CML. The absorbance increments are interpreted as polycondensation reactions with furfural and other degradation products of hemicelluloses with the lignin moiety of the cell wall.

Sign in / Sign up

Export Citation Format

Share Document