scholarly journals Development of an in-process micro tensile tester and its application for measurement of the mechanical properties and adhesion forces of cells (Quantitative analysis of a cancer cell stiffness and adhesion forces)

2020 ◽  
Vol 86 (892) ◽  
pp. 20-00311-20-00311
Author(s):  
Shota OBATA ◽  
Kazuaki NAGAYAMA
Keyword(s):  
Mechanical Properties ◽  
Quantitative Analysis ◽  
Cancer Cell ◽  
Cell Stiffness ◽  
Adhesion Forces ◽  
Tensile Tester

scholarly journals Actin cytoskeleton deregulation confers midostaurin resistance in FLT3-mutant acute myeloid leukemia

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Andoni Garitano-Trojaola ◽  
Ana Sancho ◽  
Ralph Götz ◽  
Patrick Eiring ◽  
Susanne Walz ◽  
...  
Keyword(s):  
Acute Myeloid Leukemia ◽  
Actin Cytoskeleton ◽  
Myeloid Leukemia ◽  
Actin Polymerization ◽  
Cell Stiffness ◽  
Adhesion Forces ◽  
Frequent Mutations ◽  
New Perspective ◽  
The Impact ◽  
Acute Myeloid

AbstractThe presence of FMS-like tyrosine kinase 3-internal tandem duplication (FLT3-ITD) is one of the most frequent mutations in acute myeloid leukemia (AML) and is associated with an unfavorable prognosis. FLT3 inhibitors, such as midostaurin, are used clinically but fail to entirely eradicate FLT3-ITD + AML. This study introduces a new perspective and highlights the impact of RAC1-dependent actin cytoskeleton remodeling on resistance to midostaurin in AML. RAC1 hyperactivation leads resistance via hyperphosphorylation of the positive regulator of actin polymerization N-WASP and antiapoptotic BCL-2. RAC1/N-WASP, through ARP2/3 complex activation, increases the number of actin filaments, cell stiffness and adhesion forces to mesenchymal stromal cells (MSCs) being identified as a biomarker of resistance. Midostaurin resistance can be overcome by a combination of midostaruin, the BCL-2 inhibitor venetoclax and the RAC1 inhibitor Eht1864 in midostaurin-resistant AML cell lines and primary samples, providing the first evidence of a potential new treatment approach to eradicate FLT3-ITD + AML.

A Nanoindentation Method for Hydrated Compliant Materials

2011 ◽  
Author(s):  
Donna M. Ebenstein
Keyword(s):  
Mechanical Properties ◽  
Soft Tissues ◽  
Adhesion Forces ◽  
Surface Detection ◽  
Heterogeneous Samples ◽  
Mineralized Tissues ◽  
Fluid Interactions

Nanoindentation is becoming an increasingly popular tool in the biomaterials field due to its ability to measure local mechanical properties in small, irregularly-shaped or heterogeneous samples.1 Although this technique was readily adapted to the study of mineralized tissues, the application of nanoindentation to compliant, hydrated biomaterials such as soft tissues and hydrogels has led to many challenges.1 Three key concerns associated with nanoindentation of compliant, hydrated materials are inaccurate surface detection, errors due to adhesion forces, and fluid interactions with the tip.1–4

Correction to Quantitative Analysis of the Human AKR Family Members in Cancer Cell Lines Using the mTRAQ/MRM Approach

2013 ◽  
Vol 12 (9) ◽  
pp. 4255-4255
Author(s):  
Shenyan Zhang ◽  
Bo Wen ◽  
Baojin Zhou ◽  
Lei Yang ◽  
Chao Cha ◽  
...  
Keyword(s):  
Quantitative Analysis ◽  
Cell Lines ◽  
Cancer Cell ◽  
Family Members ◽  
Cancer Cell Lines

scholarly journals Curing and mechanical properties of chlorosulphonated polyethylene rubber blends

2011 ◽  
Vol 17 (3) ◽  
pp. 315-321 ◽  
Author(s):  
Gordana Markovic ◽  
Vojislav Jovanovic ◽  
Suzana Samarzija-Jovanovic ◽  
Milena Marinovic-Cincovic ◽  
Jaroslava Budinski-Simendic
Keyword(s):  
Mechanical Properties ◽  
Crosslink Density ◽  
Hydraulic Press ◽  
Elongation At Break ◽  
Rubber Blends ◽  
Tensile Tester ◽  
Roll Mill ◽  
Cure Time ◽  
Chlorosulphonated Polyethylene ◽  
Scanning Electron

In this paper the curing and mechanical properties of two series of prepared blends, i.e., chlorosulphonated polyethylene (CSM)/isobutylene-co-isoprene (IIR) rubber blends and chlorosulphonated polyethylene (CSM)/chlorinated isobutylene-co-isoprene (CIIR) rubber blends were carried out. Blends were prepared using a two roll-mill at a temperature of 40-50?C. The curing was assessed by using a Monsanto Oscillating Disc Rheometer R-100. The process of vulcanization accelerated sulfur of pure rubbers and their blends was carried out in an electrically heated laboratory hydraulic press under a pressure of about 4 MPa and 160?. The stress-strain experiments were performed using tensile tester machine (Zwick 1425). Results indicate that the scorch time, ts2 and optimum cure time, tc90 increase with increasing CSM content in both blends. The values of modulus at 100% and at 300% elongation and tensile strength increases with increasing CSM content, whereas elongation at break shows a decreasing trend. The enhancement in mechanical properties was supported by data of crosslink density in these samples obtained from swelling measurement and scanning electron microscopy studies of the rubber blends fractured surfaces.

Sign in / Sign up

Export Citation Format

Share Document