scholarly journals HYDROPHOBIC IMPREGNATION OF GEOPOLYMER COMPOSITE BY ETHOXYSILANES

2018 ◽  
Vol 58 (3) ◽  
pp. 184
Author(s):  
Zdeněk Mašek ◽  
Linda Diblikova
Keyword(s):  
Contact Angle ◽  
Elevated Temperature ◽  
Water Contact Angle ◽  
Water Uptake ◽  
Outer Surface ◽  
Alkyl Group ◽  
Sio2 Nanoparticles ◽  
Water Contact ◽  
Composite Surface ◽  
Geopolymer Composites

A geopolymer composite was impregnated by incorporating the hydrophobic alkyl group on the outer surface and in the inner structure of the geopolymer. Ethoxysilanes 1H,1H,2H,2H perfluoroctyltriethoxysilane and hexadecyltrimethoxysilane were used as the source of hydrophobic groups. Three types of solutions based on the ethoxysilanes were prepared according to adapted procedures. The modification of the geopolymer composites was done by their immersion into the hydrophobic solutions followed by drying at a laboratory or elevated temperature. The effectivity of the procedure was evaluated by measuring the water contact angle on the surface of the modified composite and by measuring the water uptake and stiffness of the composite. The results confirmed that the silanes hydrolyzed in sol containing SiO2 nanoparticles have a higher hydrophobization effect than solutions of simply hydrolyzed silanes. The resulting impregnation procedure led to the change of the geopolymer composite surface from hydrophilic to hydrophobic.

scholarly journals Fabrication of Electrospun Membranes based on Poly(caprolactone) (PCL) and PCL/Chitosan Layer by Layer for Tissue Engineering

2017 ◽  
Vol 17 (1) ◽  
Author(s):  
Choi Yee Foong ◽  
Naznin Sultana
Keyword(s):  
Tissue Engineering ◽  
Contact Angle ◽  
Water Contact Angle ◽  
Water Uptake ◽  
Solution Concentration ◽  
Layered Composite ◽  
Layer By Layer ◽  
Electrospun Membrane ◽  
Water Contact ◽  
Electrospun Membranes

Recently, in the field of tissue engineering, fabrication of three-dimensional (3D) electrospun scaffold or membrane is much emphasized. In this study, layered composite scaffolds or membranes were fabricated using two biodegradable polymers, polycaprolactone (PCL) and Chitosan layer-by-layer with multilayer electrospinning method. Characterizations of membranes were done using several techniques. Electrospun composite membrane’s surface morphology was examined using a Scanning Electron Microscopy (SEM) and the wettability of the material’s surface was determined using water contact angle measuring measurement (WCA). Water uptake properties of electrospun membrane were also determined. Using optimized solution concentration and electrospinning processing parameters, the composite PCL/Chitosan and PCL layer-by-layer were successfully fabricated. It was observed from SEM that the composite electrospun membranes produced consisted microfibers and nanofibers within single scaffold. The water contact angle for the double-layered composite electrospun membranes was lower than the pure PCL. The double-layered composite membrane also had higher water uptake properties compared to pure PCL scaffold.

scholarly journals Alicyclic Polyimide/SiO2 Mixed Matrix Membranes for Water/n-Butanol Pervaporation

Membranes ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 564
Author(s):  
Ching-Wen Hsieh ◽  
Bo-Xian Li ◽  
Shing-Yi Suen
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Separation Factor ◽  
Separation Efficiency ◽  
Sio2 Nanoparticles ◽  
Mixed Matrix Membranes ◽  
Mixed Matrix ◽  
Water Contact ◽  
Solvent Swelling ◽  
Matrix Membranes

Alicyclic polyimides (PIs) have excellent properties in solubility, mechanical strength, thermal property, etc. This study developed two types of alicyclic PI-based mixed matrix membranes (MMMs) for water/n-butanol pervaporation application, which have never been investigated previously. The fillers were hydrophilic SiO2 nanoparticles. The synthesized PI was mixed with SiO2 nanoparticles in DMAc to make the casting solution, and a liquid film was formed over PET substrate using doctor blade. A dense MMM was fabricated at 80 °C and further treated via multi-stage curing (100–170 °C). The prepared membranes were characterized by FTIR, TGA, FE-SEM, water contact angle, and solvent swelling. The trends of pure solvent swelling effects agree well with the water contact angle results. Moreover, the pervaporation efficiencies of alicyclic PI/SiO2 MMMs for 85 wt% n-butanol aqueous solution at 40 °C were investigated. The results showed that BCDA-3,4′-ODA/SiO2 MMMs had a larger permeation flux and higher separation factor than BCDA-1,3,3-APB/SiO2 MMMs. For both types of MMMs, the separation factor increased first and then decreased, with increasing SiO2 loading. Based on the PSI performance, the optimal SiO2 content was 0.5 wt% for BCDA-3,4′-ODA/SiO2 MMMs and 5 wt% for BCDA-1,3,3-APB/SiO2 MMMs. The overall separation efficiency of BCDA-3,4′-ODA-based membranes was 10–30-fold higher.

Long-Term Stable Metal Organic Framework (MOF) Based Mixed Matrix Membranes for Ultrafiltration

2020 ◽  
Author(s):  
Muayad Al-shaeli ◽  
Stefan J. D. Smith ◽  
Shanxue Jiang ◽  
Huanting Wang ◽  
Kaisong Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Mixed Matrix Membranes ◽  
Recovery Ratio ◽  
Mixed Matrix ◽  
Water Contact ◽  
Membrane Performance ◽  
Metal Organic ◽  
Matrix Membranes

<p>In this study, novel <a>mixed matrix polyethersulfone (PES) membranes</a> were synthesized by using two different kinds of metal organic frameworks (MOFs), namely UiO-66 and UiO-66-NH<sub>2</sub>. The composite membranes were characterised by SEM, EDX, FTIR, PXRD, water contact angle, porosity, pore size, etc. Membrane performance was investigated by water permeation flux, flux recovery ratio, fouling resistance and anti-fouling performance. The stability test was also conducted for the prepared mixed matrix membranes. A higher reduction in the water contact angle was observed after adding both MOFs to the PES and sulfonated PES membranes compared to pristine PES membranes. An enhancement in membrane performance was observed by embedding the MOF into PES membrane matrix, which may be attributed to the super-hydrophilic porous structure of UiO-66-NH<sub>2</sub> nanoparticles and hydrophilic structure of UiO-66 nanoparticles that could accelerate the exchange rate between solvent and non-solvent during the phase inversion process. By adding the MOFs into PES matrix, the flux recovery ratio was increased greatly (more than 99% for most mixed matrix membranes). The mixed matrix membranes showed higher resistance to protein adsorption compared to pristine PES membranes. After immersing the membranes in water for 3 months, 6 months and 12 months, both MOFs were stable and retained their structure. This study indicates that UiO-66 and UiO-66-NH<sub>2</sub> are great candidates for designing long-term stable mixed matrix membranes with higher anti-fouling performance.</p>

scholarly journals Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Andrzej Sikora ◽  
Dariusz Czylkowski ◽  
Bartosz Hrycak ◽  
Magdalena Moczała-Dusanowska ◽  
Marcin Łapiński ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Chemical Composition ◽  
Water Contact Angle ◽  
Plasma Sheet ◽  
Atmospheric Pressure ◽  
Argon Plasma ◽  
Fullerene Derivative ◽  
Water Contact ◽  
Pmma Polymer

AbstractThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

scholarly journals Physicochemical Properties and Biocompatibility of Electrospun Polycaprolactone/Gelatin Nanofibers

2021 ◽  
Vol 18 (9) ◽  
pp. 4764
Author(s):  
Wei Lee Lim ◽  
Shiplu Roy Chowdhury ◽  
Min Hwei Ng ◽  
Jia Xian Law
Keyword(s):  
Contact Angle ◽  
Physicochemical Properties ◽  
Water Contact Angle ◽  
Ligament Injury ◽  
Great Promise ◽  
Composition Analysis ◽  
Water Contact ◽  
Tenogenic Differentiation ◽  
Good Biocompatibility ◽  
Tissue Grafts

Tissue-engineered substitutes have shown great promise as a potential replacement for current tissue grafts to treat tendon/ligament injury. Herein, we have fabricated aligned polycaprolactone (PCL) and gelatin (GT) nanofibers and further evaluated their physicochemical properties and biocompatibility. PCL and GT were mixed at a ratio of 100:0, 70:30, 50:50, 30:70, 0:100, and electrospun to generate aligned nanofibers. The PCL/GT nanofibers were assessed to determine the diameter, alignment, water contact angle, degradation, and surface chemical analysis. The effects on cells were evaluated through Wharton’s jelly-derived mesenchymal stem cell (WJ-MSC) viability, alignment and tenogenic differentiation. The PCL/GT nanofibers were aligned and had a mean fiber diameter within 200–800 nm. Increasing the GT concentration reduced the water contact angle of the nanofibers. GT nanofibers alone degraded fastest, observed only within 2 days. Chemical composition analysis confirmed the presence of PCL and GT in the nanofibers. The WJ-MSCs were aligned and remained viable after 7 days with the PCL/GT nanofibers. Additionally, the PCL/GT nanofibers supported tenogenic differentiation of WJ-MSCs. The fabricated PCL/GT nanofibers have a diameter that closely resembles the native tissue’s collagen fibrils and have good biocompatibility. Thus, our study demonstrated the suitability of PCL/GT nanofibers for tendon/ligament tissue engineering applications.

Osteoconductivity of Superhydrophilic Ti- and Zr-Alloy for Biomedical Application

2016 ◽  
Vol 879 ◽  
pp. 2524-2527
Author(s):  
Masazumi Okido ◽  
Kensuke Kuroda
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Strong Influence ◽  
Biomedical Application ◽  
Hydrophobic Surface ◽  
Hydrophilic Surface ◽  
Water Contact ◽  
Zr Alloy ◽  
Zr Alloys

Surface hydrophilicity is considered to have a strong influence on the biological reactions of bone-substituting materials. However, the influence of a hydrophilic or hydrophobic surface on the osteoconductivity is not completely clear. In this study, we produced super-hydrophilic and hydrophobic surface on Ti-and Zr-alloys. Hydrothermal treatment at 180 oC for 180 min. in the distilled water and immersion in x5 PBS(-) brought the super-hydrophilic surface (water contact angle < 10 (deg.)) and heat treatment of as-hydrothermaled the hydrophobic surface. The osteoconductivity of the surface treated samples with several water contact angle was evaluated by in vivo testing. The surface properties, especially water contact angle, strongly affected the osteoconductivity and protein adsorbability, and not the surface substance.

scholarly journals Vertical Orientation of Liquid Crystal on Polystyrene Substituted with n-Alkylbenzoate-p-oxymethyl Pendant Group as a Liquid Crystal Precursor

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2058
Author(s):  
Kyutae Seo ◽  
Hyo Kang
Keyword(s):  
Contact Angle ◽  
Liquid Crystal ◽  
Water Contact Angle ◽  
Polymer Films ◽  
Molar Fraction ◽  
Side Chain ◽  
Pendant Group ◽  
Polymer Modification ◽  
Vertical Orientation ◽  
Water Contact

We synthesized a series of polystyrene derivatives modified with precursors of liquid crystal (LC) molecules via polymer modification reactions. Thereafter, the orientation of the LC molecules on the polymer films, which possess part of the corresponding LC molecular structure, was investigated systematically. The precursors and the corresponding derivatives used in this study include ethyl-p-hydroxybenzoate (homopolymer P2BO and copolymer P2BO#, where # indicates the molar fraction of ethylbenzoate-p-oxymethyl in the side chain (# = 20, 40, 60, and 80)), n-butyl-p-hydroxybenzoate (P4BO), n-hexyl-p-hydroxybenzoate (P6BO), and n-octyl-p-hydroxybenzoate (P8BO). A stable and uniform vertical orientation of LC molecules was observed in LC cells fabricated with P2BO#, with 40 mol% or more ethylbenzoate-p-oxymethyl side groups. In addition, the LC molecules were oriented vertically in LC cells fabricated with homopolymers of P2BO, P4BO, P6BO, and P8BO. The water contact angle on the polymer films can be associated with the vertical orientation of the LC molecules in the LC cells fabricated with the polymer films. For example, vertical LC orientation was observed when the water contact angle of the polymer films was greater than ~86°. Good orientation stability was observed at 150 °C and with 20 J/cm2 of UV irradiation for LC cells fabricated with the P2BO film.

Sign in / Sign up

Export Citation Format

Share Document