scholarly journals Mechanical Properties of Polyvinyl Chloride Plastics Recycled Aggregate Concrete

2018 ◽  
Vol 7 (4.19) ◽  
pp. 853
Author(s):  
Adel A. Al-Azzawi ◽  
Mustafa S. Shalal
Keyword(s):  
Polyvinyl Chloride ◽  
Concrete Strength ◽  
Strength Properties ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Engineering Properties ◽  
Replacement Ratio ◽  
Aggregate Concrete ◽  
Coarse Aggregates ◽  
Tension And Compression

The concrete prepared with Polyvinyl chloride plastics (collected from doors and windows wastes) as recycled coarse aggregates and their concrete engineering properties are studied in the laboratory in this research. The concrete blends have an expected cylinder compressive strength of 28 MPa. In this research, the concrete blends contain plasticcoarse aggregate.The ratio of this aggregate to the total aggregate volume ranges from 0 to 1. The concrete strength properties in tension and compression are greatly affected with the plastic replacement ratio. The blends density reduces with increasing replacement ratio. For low replacement ratio, the effect is practically marginal. It is not acceptable to use ACI 318 code spilt cylinder equation for plasticaggregate concrete with higher replacement ratio  

scholarly journals Numerical Study of Bond Slip between Section Steel and Recycled Aggregate Concrete with Full Replacement Ratio

2020 ◽  
Vol 10 (3) ◽  
pp. 887 ◽  
Author(s):  
Chao Liu ◽  
Lu Xing ◽  
Huawei Liu ◽  
Zonggang Quan ◽  
Guangming Fu ◽  
...  
Keyword(s):  
Numerical Study ◽  
Concrete Strength ◽  
Limit State ◽  
Control Variable ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Replacement Ratio ◽  
Aggregate Concrete ◽  
Bond Slip ◽  
Bond Behavior

In this paper, the bond deterioration mechanism of recycled aggregate concrete (RAC) with a full replacement ratio was studied through experimental and numerical simulations. To study the bond behavior and the bond slip between section steel and RAC, nine push-out specimens were designed using the control variable method. The effects of the concrete strength, the embedded length, the cover thickness, and the lateral stirrup ratio on the bond behavior and the bond slip were investigated in detail. The loading process and failure mode of the specimens were observed, and the test curves of the loading end and free end of the specimens were analyzed. Based on the experiment, the finite element method (FEM) was used to simulate the specimens, and the simulation results were analyzed by comparing the experiment data. The analysis of the results showed that the developed model is capable of representing the characteristic bond strength value between section steel and RAC with sufficient accuracy, and the main differences of bond slip between the simulation and the test results are the slippage at the limit state and the moment at which the free end starts to slip.

Chloride Resistance of Recycled Aggregate Concrete under Wetting-Drying Cycles

2016 ◽  
Vol 724 ◽  
pp. 3-7 ◽  
Author(s):  
Bing Qi ◽  
Jian Ming Gao ◽  
Da Man Shen
Keyword(s):  
Chloride Content ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Chloride Diffusion ◽  
Replacement Ratio ◽  
Aggregate Concrete ◽  
Coarse Aggregates ◽  
Free Chloride ◽  
Chloride Resistance

Recycled aggregates concrete (RAC) becomes an important participant in recycled materials. This study was performed in order to evaluate the effect of recycled coarse aggregates (RCA) on the chloride resistance of concretes with different coarse aggregates replacement ratio under wetting–drying cycles. Composition influence on the concrete were studied with different the addition of admixtures. The results indicate that the free chloride content decreased with the increasing of depth, whist it increased with the increasing replacement ratio of RCA at the same depth. Wetting–drying cycles accelerated the process of chloride diffusion. It was also found that the addition of admixtures can improve the ability of chloride resistance of concrete.

scholarly journals Study on the Strength Performance of Recycled Aggregate Concrete with Different Ages under Direct Shearing

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2312
Author(s):  
Xin Liang ◽  
Fang Yan ◽  
Yuliang Chen ◽  
Huiqin Wu ◽  
Peihuan Ye ◽  
...  
Keyword(s):  
Shear Strength ◽  
Shear Force ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Displacement Curve ◽  
Direct Shear ◽  
Replacement Ratio ◽  
Aggregate Concrete ◽  
Concrete Failure ◽  
Load Displacement

In order to study the mechanical properties of recycled aggregate concrete (RAC) at different ages, 264 standard cubes were designed to test its direct shear strength and cube compressive strength while considering the parameters of age and recycled aggregate replacement ratio. The failure pattern and load–displacement curve of specimens at direct shearing were obtained; the direct shear strength and residual shear strength were extracted from the load–displacement curves. Experimental results indicate that the influence of the replacement ratio for the front and side cracks of RAC is insignificant, with the former being straight and the latter relatively convoluted. At the age of three days, the damaged interface between aggregate and mortar is almost completely responsible for concrete failure; in addition to the damage of coarse aggregates, aggregate failure is also an important factor in concrete failure at other ages. The load–displacement curve of RAC at direct shearing can be divided into elasticity, elastoplasticity, plasticity, and stabilization stages. The brittleness of concrete decreases with its age, which is reflected in the gradual shortening of the elastoplastic stage. At 28 days of age, the peak direct shear force increases with the replacement ratio, while the trend is opposite at ages of 3 days, 7 days, and 14 days, respectively. The residual strength of RAC decreases inversely to the replacement ratio, with the rate of decline growing over time. A two-parameter RAC direct shear strength calculation formula was established based on the analysis of age and replacement rate to peak shear force of RAC. The relationship between cube compressive strength and direct shear strength of recycled concrete at various ages was investigated.

Effects of maximum particle size of coarse aggregates and steel fiber contents on the mechanical properties and impact resistance of recycled aggregate concrete

2021 ◽  
pp. 136943322110179
Author(s):  
DongTao Xia ◽  
ShaoJun Xie ◽  
Min Fu ◽  
Feng Zhu
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Steel Fiber ◽  
Impact Resistance ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Coarse Aggregates ◽  
Maximum Particle Size ◽  
Maximum Particle

Fiber reinforced recycled aggregate concrete has become a new type of green concrete material. The maximum particle size of coarse aggregates and steel fiber contents affect the mechanical properties and impact resistance of recycled aggregate concrete. However, such studies are rare in literature. The present paper shortens the gap through experimental study. A total of 144 specimens of 12 kinds of concrete mixtures were tested, which adopted different steel fiber volume admixtures (0%, 0.8%, 1.0%, 1.2%) and recycled coarse aggregates in different maximum particle sizes (9.5, 19, 31.5 mm) replacing 30% natural coarse aggregate. The compressive strength, splitting tensile strength, and impact resistance of the 12 concrete mixtures were tested. The results showed that the compressive strength, splitting tensile strength, and impact resistance of recycled aggregate concrete increased first and then decreased with the increase of the maximum particle size. The recycled aggregate concrete with the maximum particle size of 19 mm had the highest mechanical properties and impact resistance. Besides, with the increase of steel fiber content, the compressive strength, splitting tensile strength, and impact resistance of recycled aggregate concrete showed an increasing trend. Considering a large amount of experimental data and the coupling effect of steel fiber contents and the maximum particle size of coarse aggregates, the Weibull distribution function was introduced to analyze the impact test results and predict the number of resistance to impact under different failure probabilities. The results showed that the number of blows of the recycled aggregate concrete followed a two-parameter Weibull distribution, and the estimated value of the number of resistance to impact for failure increased with the increase of the failure probability.

scholarly journals Discrete Element Mesoscale Modeling of Recycled Lump Concrete under Axial Compression

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3140 ◽  
Author(s):  
Yong Yu ◽  
Bo Wu
Keyword(s):  
Mechanical Properties ◽  
Axial Compression ◽  
Discrete Element ◽  
Relative Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Ordinary Concrete ◽  
Coarse Aggregates ◽  
Spatial Locations

In the past decade, directly reusing large pieces of coarsely crushed concrete (referred to as demolished concrete lumps or DCLs) with fresh concrete in new construction was demonstrated as an efficient technique for the recycling of waste concrete. Previous studies investigated the mechanical properties of recycled lump concrete (RLC) containing different sizes of DCLs; however, for actual application of this kind of concrete, little information is known about the influence of the spatial locations of DCLs and coarse aggregates on the concrete strength. Moreover, the mechanical responses of such a concrete containing various shapes of DCLs are also not well illustrated. To add knowledge related to these topics, two-dimensional mesoscale simulations of RLC containing DCLs under axial compression were performed using the discrete element method. The main variables of interest were the relative strength of the new and old concrete, the distribution of the lumps and other coarse aggregates, and the shape of the lumps. In addition, the differences in compression behavior between RLC and recycled aggregate concrete were also predicted. The numerical results indicate that the influence tendency of the spatial locations of DCLs and coarse aggregate pieces on the compressive stress–strain curves for RLC is similar to that of the locations of coarse aggregates for ordinary concrete. The strength variability of RLC is generally higher than that of ordinary concrete, regardless of the relative strength of the new and old concrete included; however, variability has no monotonic trend with an increase in the lump replacement ratio. The mechanical properties of RLC in compression are little influenced by the geometric shape of DCLs as long as the ratio of the length of their long axis to short axis is smaller than 2.0. The compressive strength and elastic modulus of RLC are always superior to those of recycled aggregate concrete designed with a conventional mixing method.

scholarly journals Carbonation Properties of Recycled Aggregate Concrete by Specified Concrete Strength

2017 ◽  
Vol 5 (1) ◽  
pp. 85-93
Author(s):  
Jun Lee ◽  
Bong-Chun Lee ◽  
Young-Keun Cho ◽  
Kwang-Min Park ◽  
Sang-Hwa Jung
Keyword(s):  
Concrete Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete

Performance Enhancement of Recycled Aggregate Concrete – An Experimental Study

2021 ◽  
Author(s):  
Sivamani Jagan ◽  
Thurvas Renganathan Neelakantan ◽  
Palaniraj Saravanakumar
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Elastic Modulus ◽  
Performance Enhancement ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Coarse Aggregates ◽  
Durability Properties ◽  
Concrete Mixtures

Extensive studies have been performed on the mechanical and durability properties of the concrete prepared with recycled coarse aggregates (RCA), however, only modest consideration has been given to the studies on the behaviour of RAC prepared by alternative mixing approach techniques. This study presents the mechanical properties of the recycled aggregate concrete (RAC) with different percentages of RCA prepared by normal mixing approach (NMA), two-stage mixing approach (TSMA) and sand enveloped mixing approach (SEMA) techniques. The manufactured concrete mixtures were tested for compression, tension, flexure and elastic modulus at 7, 28 and 90 days. The results indicate that the mechanical properties of the RAC (with 100% of RCA) prepared through TSMA and SEMA were improved by 9.36 and 12.14% at 28 days. Perhaps, prolonged curing to TSMA and SEMA mixtures improved the mechanical properties of the RAC that is nearly equal to normal aggregate concrete (NAC) prepared by NMA.

scholarly journals Sulfate Resistance of Recycled Aggregate Concrete with GGBS and Fly Ash-Based Geopolymer

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1247 ◽  
Author(s):  
Jianhe Xie ◽  
Jianbai Zhao ◽  
Junjie Wang ◽  
Chonghao Wang ◽  
Peiyan Huang ◽  
...  
Keyword(s):  
Fly Ash ◽  
Construction Projects ◽  
High Performance ◽  
High Performance Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Aggregate Concrete ◽  
Sulfate Resistance ◽  
Coarse Aggregates

There is a constant drive for the development of ultra-high-performance concrete using modern green engineering technologies. These concretes have to exhibit enhanced durability and incorporate energy-saving and environment-friendly functions. The object of this work was to develop a green concrete with an improved sulfate resistance. In this new type of concrete, recycled aggregates from construction and demolition (C&D) waste were used as coarse aggregates, and granulated blast furnace slag (GGBS) and fly ash-based geopolymer were used to totally replace the cement in concrete. This study focused on the sulfate resistance of this geopolymer recycled aggregate concrete (GRAC). A series of measurements including compression, X-ray diffraction (XRD), and scanning electron microscopy (SEM) tests were conducted to investigate the physical properties and hydration mechanisms of the GRAC after different exposure cycles in a sulfate environment. The results indicate that the GRAC with a higher content of GGBS had a lower mass loss and a higher residual compressive strength after the sulfate exposure. The proposed GRACs, showing an excellent sulfate resistance, can be used in construction projects in sulfate environments and hence can reduce the need for cement as well as the disposal of C&D wastes.

scholarly journals Probabilistic Conversion of the Compressive Strength of Cubes to Cylinders of Natural and Recycled Aggregate Concrete Specimens

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 280 ◽  
Author(s):  
João Pacheco ◽  
Jorge de Brito ◽  
Carlos Chastre ◽  
Luís Evangelista
Keyword(s):  
Compressive Strength ◽  
Conversion Factor ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Structural Behaviour ◽  
Aggregate Concrete ◽  
Coarse Aggregates ◽  
Natural Aggregate ◽  
Using Data ◽  
The Relationship

This paper investigates the effect of recycled coarse aggregate incorporation on the relationship between 150 mm cubic and Փ 150 mm cylindrical compressive strength (the reference strength of standards) by comparing data from recycled and natural aggregate concrete compositions in which both cubes and cylinders were tested. A conversion factor from cubic to cylindrical strength is proposed in two versions: A deterministic and a probabilistic one. Such factor has not been studied before and researchers have been converting cubic data as if natural aggregate concrete were tested. The probabilistic factor is intended for reliability analyses on the structural behaviour of recycled aggregate concrete using data from laboratory cube tests. It was found that the incorporation of recycled coarse aggregates sourced from concrete waste significantly decreases the expected value of the factor but the factor’s scatter is relatively unaffected.

Experimental Study on Compressive Strength of Recycled Aggregate Concrete with Different Replacement Ratios

2012 ◽  
Vol 174-177 ◽  
pp. 1277-1280 ◽  
Author(s):  
Hai Yong Cai ◽  
Min Zhang ◽  
Ling Bo Dang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Failure Mode ◽  
Failure Process ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Replacement Ratio ◽  
Aggregate Concrete

Compressive strengths of recycled aggregate concrete(RAC) with different recycled aggregates(RA) replacement ratios at 7d, 28d, 60d ages are investigated respectively. Failure process and failure mode of RAC are analyzed, influences on compressive strength with same mix ratio and different RA replacement ratios are analyzed, and the reason is investigated in this paper. The experimental results indicate that compressive strength of recycled concrete at 28d age can reach the standard generally, it is feasible to mix concrete with recycled aggregates, compressive strength with 50% replacement ratio is relatively high.

Sign in / Sign up

Export Citation Format

Share Document