FATIGUE TEST OF STEEL GIRDER WEB PENETRATION DETAILS WITH A SLIT

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Naoto Yoshida ◽  
Masahiro Sakano ◽  
Hideyuki Konishi ◽  
Takashi Fujii
Keyword(s):  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Cracking ◽  
Highway Bridges ◽  
Strength Properties ◽  
Fatigue Tests ◽  
Bottom Surface ◽  
Steel Girder ◽  
Propagation Behavior

Fatigue cracking in steel girder web penetration details is so dangerous that it can break steel girders. A one-meter-long crack was detected in Yamazoe Bridge in 2006. Since a number of highway bridges with such web penetration details may exist in Japan, it is of urgent importance to understand these fatigue-strength properties. However, few fatigue tests have been reported on steel girder web penetration details. The purpose of this study is to clarify fatigue behavior of steel girder web penetration details with a slit through fatigue tests of specimens with these details. We designed and fabricated girder specimens that have steel girder web penetration details, in which cross-beam bottom flanges are connected to each top or bottom surface of a slit by welding. First, we conducted static loading tests to understand the stress distributions around web penetration details. Second, we conducted fatigue tests to examine fatigue crack initiation and propagation behavior and fatigue strength.

THREE FACE ATTACHMENT RETROFIT AGAINST FATIGUE CRACKING AT STEEL GIRDER WEB PENETRATION

2018 ◽  
Vol 5 (2) ◽  
Author(s):  
Chihiro Sakamoto ◽  
Masahiro Sakano ◽  
Hideyuki Konishi ◽  
Takashi Fujii
Keyword(s):  
Fatigue Strength ◽  
Stress Concentration ◽  
Stress Reduction ◽  
Fatigue Cracking ◽  
Highway Bridges ◽  
Lower Surface ◽  
Strength Properties ◽  
Fatigue Tests ◽  
Lower Side ◽  
Steel Girder

Fatigue cracking in steel girder web penetration details is so dangerous that it can break steel girders. Since a number of highway bridges have such web penetration details in Japan, it is of urgent importance to grasp these fatigue strength properties. In this study, we investigate stress reduction effects of three face attachment retrofit through fatigue tests using a large girder specimen with web penetration details where cross beam lower flanges are connected to the lower surface of a slot by welding. As a result, there is very little difference between two and three face attachments about stress reduction effects, while they are more effective than one face attachment. The upper side attachment is more effective than the lower side attachment, while both side attachment is best. Two and three face both side attachments can reduce about 40% of stress concentration, while two and three face upper side attachments can reduce 50– 60%.

RETROFITTING METHODS AGAINST FATIGUE CRACKING IN STEEL GIRDER WEB PENETRATION

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Chihiro Sakamoto ◽  
Masahiro Sakano ◽  
Hideyuki Konishi ◽  
Takashi Fujii
Keyword(s):  
Fatigue Life ◽  
Fatigue Cracking ◽  
Highway Bridges ◽  
Lower Surface ◽  
Strength Properties ◽  
Fatigue Tests ◽  
Stress Distributions ◽  
Steel Girder ◽  
Cracking Behavior ◽  
Weld Toe

Fatigue cracking in steel girder web penetration details is so dangerous that it can break steel girders. Since a number of highway bridges have such web penetration details in Japan, it is of urgent importance to grasp these fatigue strength properties and develop effective retrofitting methods. In a previous report, we investigated the stress distributions around web penetration details, and fatigue cracking behavior, using steel girder specimens with web penetration details. In this study, we investigate effects of retrofitting methods against fatigue cracking in web penetration details through fatigue tests using large girder specimens with web penetration details in which cross beam lower flanges are connected to lower surface of a slot by welding. Principal results obtained through this study are as follows: (1) Weld toe grinding can extend fatigue life more than 5 times, (2) Two-face attachment can extend fatigue life more than 10 times, and (3) Two-face attachment with weld toe grinding can extend fatigue life more than 25 times.

scholarly journals Effect of Aqueous Environment on High Cycle and Very-High-Cycle Fatigue Behavior for a Structural Steel

2011 ◽  
Vol 462-463 ◽  
pp. 355-360
Author(s):  
You Shi Hong ◽  
Gui An Qian
Keyword(s):  
Fatigue Strength ◽  
Structural Steel ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Aqueous Environment ◽  
Cycle Fatigue ◽  
Very High Cycle Fatigue ◽  
Very High

In this paper, rotary bending fatigue tests for a structural steel were performed in laboratory air, fresh water and 3.5% NaCl aqueous solution, respectively, thus to investigate the influence of environmental media on the fatigue propensity of the steel, especially in high cycle and very-high-cycle fatigue regimes. The results show that the fatigue strength of the steel in water is remarkably degraded compared with the case tested in air, and that the fatigue strength in 3.5% NaCl solution is even lower than that tested in water. The fracture surfaces were examined to reveal fatigue crack initiation and propagation characteristics in air and aqueous environments.

Fatigue Behavior of Extruded Mg-Al-Ca-Mn Alloy with T6 Treatment at Elevated Temperature

2014 ◽  
Vol 627 ◽  
pp. 417-420 ◽  
Author(s):  
Yukio Miyashita ◽  
Hugo Inzunza ◽  
Adrian Elizondo ◽  
Yoshiyuki Murayama ◽  
Yuichi Otsuka ◽  
...  
Keyword(s):  
Heat Treatment ◽  
High Temperature ◽  
Fatigue Strength ◽  
Fatigue Test ◽  
Room Temperature ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Property ◽  
Propagation Behavior ◽  
Replication Technique

Fatigue behavior of Mg-Al-Ca-Mn alloy with T6 treatment was studied at room temperature and 150°C by conduction rotating bending fatigue test. Fatigue strength at high temperature was lower than that at room temperature in the alloys with and without heat treatment. However, degradation of fatigue strength at high temperature in the T6 treated alloy was not significant compared to the as-extruded alloy. Fatigue crack initiation and propagation behavior was observed with replication technique by conducting interrupted fatigue test at room temperature and 150°C. Multiple cracking was significantly observed at 150°C in both as-received and T6 treated alloys. Change in grain size and randomization of crystal orientation due to the heat treatment could affect the fatigue property.

scholarly journals Effect of micro-notches on fatigue strength of electrodeposited nanocrystalline nickel thin films

2018 ◽  
Vol 165 ◽  
pp. 04011
Author(s):  
Keisuke Tanaka ◽  
Yuta Murase ◽  
Hirohisa Kimachi
Keyword(s):  
Thin Films ◽  
Fatigue Strength ◽  
Fatigue Limit ◽  
Stress Ratio ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Fine Grained ◽  
Nickel Thin Films ◽  
Nano Crystalline ◽  
Fictitious Crack

The effect of micro-notches on the fatigue strength of nickel thin films was studied. Two types of thin films with 10 μm thickness were produced by electrodeposition using sulfamate solution without and with brightener: ultra-fine grained film (UFG) with the grain size of 384 nm and nano-crystalline grained film (NCG) with that of 17 nm. Micro-sized notches introduced by FIB had the width of 2 μm and various depths from 8 to 150μm. Fatigue tests were conducted under the stress ratio of 0.1. The fatigue strength decreased with increasing depth of notches. NCG had much higher strength than UFG compared at the same notch depth. Notches as small as 8μm did reduce the fatigue strength of both UFG and NCG. The fatigue limit was controlled by the initiation of cracks and no non-propagating crack was observed in specimens fatigued below the fatigue limit. A model of fictitious crack successfully predicted the reduction of the fatigue limit due to micro-notches. The characteristic crack length of NCG was much smaller than the UFG, while the fatigue strength of defect-free NCG was larger than that of UFG. SEM observation of fracture surfaces was conducted to reveal micromechanisms of fatigue crack initiation.

Influence of Inner Surface Defects on the Fatigue Strength of Pipe Subjected to Cyclic Internal Pressure

1978 ◽  
Vol 100 (4) ◽  
pp. 360-368
Author(s):  
Y. Yazaki ◽  
S. Hashirizaki ◽  
S. Nishida ◽  
C. Urashima
Keyword(s):  
Fatigue Strength ◽  
Internal Pressure ◽  
Test Specimen ◽  
Surface Defects ◽  
Fatigue Crack Initiation ◽  
Internal Surface ◽  
Fatigue Tests ◽  
Inner Surface ◽  
Surface Notch ◽  
Medium Diameter

Cyclic internal oil pressure fatigue tests were carried out on medium-diameter ERW pipes of API 5LX - X60 in an attempt to determine the influence of surface defects on the fatigue strength. Experimental factors investigated were the depth and location of internal surface notch in relation to the axis of pipe. The specimen was subjected to cyclic internal pressure, the cyclic rate being 0.3–0.5 Hz. During the test, Acoustic Emission (AE) techniques were applied to detect the fatigue crack initiation. Along with the aforementioned fatigue tests, pulsating tension fatigue tests were carried out on specimens with the same surface notches as the cyclic internal pressure fatigue test specimen.

Effect of Plasma Nitriding on Ultra-High Cycle Fatigue Behaviors of Ti-6Al-4V

2011 ◽  
Vol 295-297 ◽  
pp. 2386-2389 ◽  
Author(s):  
Ren Hui Tian ◽  
Qiao Lin Ouyang ◽  
Qing Yuan Wang
Keyword(s):  
High Cycle Fatigue ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Ultrasonic Fatigue ◽  
Ultra High Cycle Fatigue ◽  
Stress Ratios

In order to investigate the effect of plasma nitriding treatment on fatigue behavior of titanium alloys, very high cycle fatigue tests were carried out for Ti-6Al-4V alloy using an ultrasonic fatigue machine under load control conditions for stress ratios of R=-1 at frequency of ƒ=20KHz. Experiment results showed that plasma nitriding treatment played the principal role in the internal fatigue crack initiation. More importantly, plasma nitriding treatment had a detrimental effect on fatigue properties of the investigated Ti-6Al-4V alloy, and the fatigue strength of material after plasma nitriding treatment appeared to be significantly reduced about 17% over the untreated material.

Effect of Processing Layer on Fatigue Strength of Extruded AZ61 Magnesium Alloy

2013 ◽  
Vol 577-578 ◽  
pp. 429-432 ◽  
Author(s):  
Yukio Miyashita ◽  
Kyohei Kushihata ◽  
Toshifumi Kakiuchi ◽  
Mitsuhiro Kiyohara
Keyword(s):  
Fatigue Crack ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Magnesium Alloy ◽  
Crack Initiation ◽  
Crack Growth ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Crack Growth Resistance ◽  
Az61 Magnesium Alloy

Fatigue Property of an Extruded AZ61 Magnesium Alloy with the Processing Layer Introduced by Machining was Investigated. Rotating Bending Fatigue Tests were Carried out with the Specimen with and without the Processing Layer. According to Results of the Fatigue Tests, Fatigue Life Significantly Increased by Introducing the Processing Layer to the Specimen Surface. Fatigue Crack Initiation and Propagation Behaviors were Observed by Replication Technique during the Fatigue Test. Fatigue Crack Initiation Life of the Specimen with the Processing Layer was Slightly Longer than that of the Specimen without the Processing Layer. Higher Fatigue Crack Growth Resistance was also Observed when the Fatigue Crack was Growing in the Processing Layer in the Specimen with the Processing Layer. the Longer Fatigue Life Observed in the Fatigue Test in the Specimen with the Processing Layer could be Mainly due to the Higher Crack Growth Resistance. it is Speculated that the Fatigue Strength can be Controlled by Change in Condition of Machining Process. it could be Effective way in Industry to Improved Fatigue Strength only by the Cutting Process without Additional Surface Treatment Process.

scholarly journals Effects of thermomechanical history and environment on the fatigue behavior of (β)-Ti-Nb implant alloys

2018 ◽  
Vol 165 ◽  
pp. 06001 ◽  
Author(s):  
André Reck ◽  
Stefan Pilz ◽  
Ulrich Thormann ◽  
Volker Alt ◽  
Annett Gebert ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Cyclic Loading ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Grain Structure ◽  
Fatigue Properties ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Implant Alloys

This study examined the fatigue properties of a newly developed cast and thermomechanical processed (β)-Ti-40Nb alloy for a possible application as biomedical alloy due to exceptional low Young’s modulus (64-73 GPa), high corrosion resistance and ductility (20-26%). Focusing on the influence of two microstructural states with fully recrystallized β-grain structure as well as an aged condition with nanometer-sized ω-precipitates, tension-compression fatigue tests (R=-1) were carried out under lab-air and showed significant differences depending on the β-phase stability under cyclic loading. Present ω- precipitates stabilized the β-phase against martensitic α’’ phase transformations leading to an increased fatigue limit of 288 MPa compared to the recrystallized state (225 MPa), where mechanical polishing and subsequent cyclic loading led to formation of α’’-phase due to the metastability of the β-phase. Additional studied commercially available (β)-Ti-45Nb alloy revealed slightly higher fatigue strength (300 MPa) and suggest a change in the dominating cyclic deformation mechanisms according to the sensitive dependence on the Nb-content. Further tests in simulated body fluid (SBF) at 37°C showed no decrease in fatigue strength due to the effect of corrosion and prove the excellent corrosion fatigue resistance of this alloy type under given test conditions.

Fatigue Behavior of Age-Hardening Cu-6Ni-1.5Si Alloys with Different Grain Sizes

2021 ◽  
Vol 1016 ◽  
pp. 125-131
Author(s):  
Masahiro Goto ◽  
T. Yamamoto ◽  
S.Z. Han ◽  
J. Kitamura ◽  
J.H. Ahn ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Fatigue Strength ◽  
Solution Heat Treatment ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
The Other ◽  
Age Hardening ◽  
Grain Sizes ◽  
Thermomechanical Processes

On the thermomechanical treatments of Cu-Ni-Si alloy, cold-rolling (CR) before solution heat treatment (SHT) is commonly conducted to eliminate defects in a casting slab. In addition, a rolling is applied to reduce/adjust the thickness of casting slab before SHT. In a heavily deformed microstructure by CR, on the other hand, grain growth during a heating in SHT is likely to occur as the result of recrystallization. In general, tensile strength and fatigue strength tend to decrease with an increase in the grain size. However, the effect of difference in grain sizes produced by with and without CR before SHT on the fatigue strength is unclear. In the present study, fatigue tests of Cu-6Ni-Si alloy smooth specimens with a grain fabricated through different thermomechanical processes were conducted. The fatigue behavior of Cu-Ni-Si alloy was discussed.

Sign in / Sign up

Export Citation Format

Share Document