The influence of injection system characteristics on the first- and second-law terms in high-speed DI diesel engines with swirl combustion chamber

2010 ◽  
Vol 7 (4) ◽  
pp. 482 ◽  
Author(s):  
A. Abassi ◽  
Sh. Khalilarya ◽  
S. Jafarmadar
Keyword(s):  
Combustion Chamber ◽  
Diesel Engines ◽  
High Speed ◽  
Injection System ◽  
Second Law ◽  
Swirl Combustion ◽  
System Characteristics

On the Mitsubishi Pre-combustion Chamber Type High Speed Diesel Engines

1939 ◽  
Vol 42 (263) ◽  
pp. 89-90
Author(s):  
Hiroshi OHINOUYE ◽  
Jiro EZAKI ◽  
Tuyosi NAKAMURA
Keyword(s):  
Combustion Chamber ◽  
Diesel Engines ◽  
High Speed ◽  
High Speed Diesel

Direct Water Injection to Improve Diesel Spray Combustion

2003 ◽  
Author(s):  
Koji Takasaki ◽  
Tatsuo Takaishi ◽  
Hiroyuki Ishida ◽  
Keijirou Tayama
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Nox Reduction ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Hole ◽  
Low Speed ◽  
Direct Water Injection

Now, it is essential to apply some measures for NOx reduction to low-speed diesel engines emitting much more NOx than high-speed engines. At the same time PM emission must be reduced especially when bunker fuel or heavy fuel is burned. This paper describes the applications of SFWI (Stratified Fuel Water Injection) system and DWI (Direct Water Injection) system to large sized diesel engines to reduce NOx and PM emission. SFWI system makes it possible to inject water during fuel injection from the same nozzle hole without mixing the liquids. DWI system injects water with high injection pressure from the other injection hole than the fuel injection hole into the combustion chamber directly. For testing both the systems, a 2-stroke-cycle low-speed test engine was used.

scholarly journals Spray Characteristics at Preheating Temperatur of Diesel-Biodiesel-Gasoline Fuel Blend

2021 ◽  
Vol 5 (2) ◽  
pp. 134
Author(s):  
Moch Miftahul Arifin ◽  
Nasrul Ilminnafik ◽  
Muh. Nurkoyim Kustanto ◽  
Agus Triono
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Fuel Mixture ◽  
Spray Angle ◽  
Injection System ◽  
Spray Characteristics ◽  
Fuel Blend ◽  
Spray Tip Penetration

Technological developments in diesel engines require improvements to the fuel injection system to meet the criteria for economical, high-power and efficient combustion and meet environmental regulatory standards. One method that has a lot of interest is changing the characteristics of the fuel, with the aim of producing optimal combustion. Spray characteristics have a big role in determining the quality of combustion in diesel engines. A good spray can improve the quality of fuel atomization and the homogeneity of the air-fuel mixture in the combustion chamber so that it can produce good engine performance and low emissions. This study aims to determine the effect of a diesel-biodiesel (Calophyllum inophyllum)-gasoline blendandfuel heating on the spray characteristics. The research was conducted with variations in composition (B0, B100, B30, B30G5 and B30G10) and fuel heating (40, 60, 80, and 100 °C). Fuel injected atapressure of 17 MPa in to a pressure chamber of 3 bar. The spray formed was recorded with a high-speed camera of 480 fps (resolution 224x168 pixel). In B100 biodiesel, the highest viscosity and density cause high spray tip penetration, small spray angle, and high spray velocity. The addition of diesel oil, gasoline, and heating fuel reduces the viscosity and density so that the spray tip penetration decreases, the spray angle increases and the velocity of spray decreases.

A New Predictive ID Model for Advanced High Speed Direct Injection Diesel Engines

2004 ◽  
Author(s):  
Lurun Zhong ◽  
Naeim A. Henein ◽  
Walter Bryzik
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Direct Injection ◽  
Combustion Process ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
Starting Conditions

Advance high speed direct injection diesel engines apply high injection pressures, exhaust gas recirculation (EGR), injection timing and swirl ratios to control the combustion process in order to meet the strict emission standards. All these parameters affect, in different ways, the ignition delay (ID) which has an impact on premixed, mixing controlled and diffusion controlled combustion fractions and the resulting engine-out emissions. In this study, the authors derive a new correlation to predict the ID under the different operating conditions in advanced diesel engines. The model results are validated by experimental data in a single-cylinder, direct injection diesel engine equipped with a common rail injection system at different speeds, loads, EGR ratios and swirl ratios. Also, the model is used to predict the performance of two other diesel engines under cold starting conditions.

Preinjection—A Measure to Influence Exhaust Quality and Noise in Diesel Engines

1989 ◽  
Vol 111 (3) ◽  
pp. 445-450 ◽  
Author(s):  
H. Schulte ◽  
E. Scheid ◽  
F. Pischinger ◽  
U. Reuter
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Combustion Noise ◽  
Injection System ◽  
Pilot Injection ◽  
Load Range ◽  
Injection Nozzle ◽  
Black Smoke ◽  
Injection Quantity ◽  
Main Injection

The combustion noise generated by DI diesel engines can be clearly reduced during both steady-state and transient operation in applying a pilot injection. After optimization, a slight increase in fuel consumption is found in the upper load range. The pilot injection also tends to reduce the NOx emissions. An increase in black smoke emissions is considered to be the main drawback with pilot injection. High-speed Schlieren photographs of injection and combustion phenomena within a pressurized chamber show that the higher black smoke emissions may be due to the combustion of the main injection quantity that occurs in a mixture that is insufficiently prepared and with nearly no delay due to the pilot injection. On the basis of these findings, it is concluded that a high degree of atomization and rapid vaporization of the main injection quantity must be accomplished. To achieve these goals better, a separate injection nozzle for the pilot quantity is preferred to an injection system with a single injection nozzle, providing both the pilot and the main quantity. Therefore, rather simple injection systems with a separate pilot injector can be developed that provide a constant pilot quantity and controlled pilot injection time over the entire engine map.

Application of HFRT Methods to Diagnose the Technical Condition of High-Speed Marine Diesel Engines

2015 ◽  
Vol 236 ◽  
pp. 161-168
Author(s):  
Tomasz Lus
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Technical Condition ◽  
Injection System ◽  
Engine Fuel ◽  
Naval Academy ◽  
Marine Diesel

The paper presents problems related to testing of the technical condition of high-speed marine diesel engines that are not equipped with indicated valves, as it is in the case of larger medium-and low-speed marine internal combustion engines. In this case, in assessment of technical condition of engine fuel injection system and valve gear system a vibration signals (in time / angle domain) analysis modified method called HFRT (High Frequency Resonance Technique) can be used. This method indirectly helps also to evaluate the fuel combustion process in the engine cylinders. The paper presents the theoretical basis of a modified HFRT method, physical implementation of the marine diesel engine system’s analyzer used for marine engines testing built at the Institute of Construction and Operation of Ships at Polish Naval Academy (PNA) in Gdynia. The paper also includes a description of the vibration signal processing methodology and examples of measurements made in the ships conditions for a few selected types of engines.

Sign in / Sign up

Export Citation Format

Share Document