scholarly journals Hydrogen Sensor Of TiO2-Based Nanomaterials

2015 ◽  
Vol 60 (2) ◽  
pp. 935-940 ◽  
Author(s):  
B. Łysoń-Sypień ◽  
K. Zakrzewska ◽  
M. Gajewska ◽  
M. Radecka
Keyword(s):  
Gas Sensing ◽  
Hydrogen Sensor ◽  
Integrating Sphere ◽  
Flame Spray ◽  
X Ray Diffraction ◽  
Hydrogen Sensing ◽  
Transmission Electron ◽  
Optical Spectrometry ◽  
Flame Spray Synthesis ◽  
Reference Atmosphere

Abstract The aim of this research was to examine gas sensing properties of TiO2 based nanomaterials. Nanopowders of Cr doped TiO2 with constant Specific Surface Area, SSA, were obtained using Flame Spray Synthesis technique, FSS. Nanomaterials were characterized by Brunauer – Emmett – Teller adsorption isotherms, BET, X – ray diffraction, XRD, Transmission Electron Microscopy, TEM, optical spectrometry UV – vis with the use of an integrating sphere as well as impedance spectroscopy. Detection of hydrogen was carried out over the concentration range of 50 - 3000 ppm at the temperatures extending from 200 to 400°C and synthetic air working as a reference atmosphere. As a result of experiments it appeared that incorporation of 5 at.% of Cr into TiO2 improved hydrogen sensing features due to small crystallite size and predominance of rutile polymorphic phase.

scholarly journals Nanocrystalline TiO2/SnO2 heterostructures for gas sensing

2017 ◽  
Vol 8 ◽  
pp. 108-122 ◽  
Author(s):  
Barbara Lyson-Sypien ◽  
Anna Kusior ◽  
Mieczylaw Rekas ◽  
Jan Zukrowski ◽  
Marta Gajewska ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Detection Threshold ◽  
Oxygen Adsorption ◽  
Flame Spray ◽  
Nanocrystalline Tio2 ◽  
Water Desorption ◽  
Hydrogen Sensing ◽  
Crystallite Sizes ◽  
Flame Spray Synthesis ◽  
Polymorphic Forms

The aim of this research is to study the role of nanocrystalline TiO2/SnO2 n–n heterojunctions for hydrogen sensing. Nanopowders of pure SnO2, 90 mol % SnO2/10 mol % TiO2, 10 mol % SnO2/90 mol % TiO2 and pure TiO2 have been obtained using flame spray synthesis (FSS). The samples have been characterized by BET, XRD, SEM, HR-TEM, Mössbauer effect and impedance spectroscopy. Gas-sensing experiments have been performed for H2 concentrations of 1–3000 ppm at 200–400 °C. The nanomaterials are well-crystallized, anatase TiO2, rutile TiO2 and cassiterite SnO2 polymorphic forms are present depending on the chemical composition of the powders. The crystallite sizes from XRD peak analysis are within the range of 3–27 nm. Tin exhibits only the oxidation state 4+. The H2 detection threshold for the studied TiO2/SnO2 heterostructures is lower than 1 ppm especially in the case of SnO2-rich samples. The recovery time of SnO2-based heterostructures, despite their large responses over the whole measuring range, is much longer than that of TiO2-rich samples at higher H2 flows. TiO2/SnO2 heterostructures can be intentionally modified for the improved H2 detection within both the small (1–50 ppm) and the large (50–3000 ppm) concentration range. The temperature T max at which the semiconducting behavior begins to prevail upon water desorption/oxygen adsorption depends on the TiO2/SnO2 composition. The electrical resistance of sensing materials exhibits a power-law dependence on the H2 partial pressure. This allows us to draw a conclusion about the first step in the gas sensing mechanism related to the adsorption of oxygen ions at the surface of nanomaterials.

Gas-Sensing Properties of Pt-V2O5 Thin Films for Ethanol Detection

2015 ◽  
Vol 659 ◽  
pp. 259-263 ◽  
Author(s):  
Viruntachar Kruefu ◽  
Pusit Pookmanee ◽  
Anurat Wisitsoraat ◽  
Sukon Phanichphant
Keyword(s):  
Vanadium Pentoxide ◽  
Gas Sensing ◽  
Nitrogen Adsorption ◽  
Flame Spray ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
X Ray ◽  
Transmission Electron ◽  
One Step ◽  
Ppm Level

In the present work, vanadium pentoxide (V2O5) nanoparticles have been investigated for monitoring ethanol (C2H5OH) at ppm levels in air. A one-step flame spray pyrolysis (FSP) process has been applied for the synthesis of vanadium pentoxide (V2O5) and platinum-loaded vanadium pentoxide (Pt-V2O5) nanoparticles. The samples have been studied to characterize their morphological and microstructural properties by X-ray diffraction and transmission electron microscopy. Pt addition to V2O5 samples were verified by energy dispersive X-ray spectrometry mode. The specific surface area of the nanoparticles was measured by nitrogen adsorption method. The application of the produced nanoparticles as sensitive and selective ethanol resistive sensor has been demonstrated. The Pt-loaded V2O5 sensor has shown higher response towards ethanol at ppm-level concentrations compared to unloaded one.

scholarly journals Study of Hollow ZnO Nanoparticles by Flame Spray Synthesis

2021 ◽  
Author(s):  
Li Hui
Keyword(s):  
Zno Nanoparticles ◽  
Hollow Structure ◽  
Synthesis Process ◽  
Flame Spray ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Uv Emission ◽  
Transmission Electron ◽  
Flame Spray Synthesis

Abstract Hollow ZnO nanoparticles prepared by flame spray synthesis(FSP) have been reported in this letter. By the results obtained from X-Ray diffraction(XRD) pattern and high-resolution transmission electron microscopy(HR-TEM) picture, it is concluded that the hollow ZnO nanoparticles were successfully synthesized at high temperature. The size of hollow nanoparticles distributed between 20 and 30 nm, and the formation mechanism of this hollow structure was discussed in the synthesis process. The strong ultra-visible(UV) emission was shown in photoluminescence(PL) spectra, while the mechanism had been explained in detail.

Polyaniline/SnO2 Nanocomposite Sensor for NO2 Gas Sensing at Low Operating Temperature

2015 ◽  
Vol 14 (04) ◽  
pp. 1550011 ◽  
Author(s):  
A. Sharma ◽  
M. Tomar ◽  
V. Gupta ◽  
A. Badola ◽  
N. Goswami
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
High Sensitivity ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Chemical Route ◽  
Sensing Properties ◽  
Response Recovery ◽  
Transmission Electron ◽  
Gas Sensing Properties

In this paper gas sensing properties of 0.5–3% polyaniline (PAni) doped SnO 2 thin films sensors prepared by chemical route have been studied towards the trace level detection of NO 2 gas. The structural, optical and surface morphological properties of the PAni doped SnO 2 thin films were investigated by performing X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Raman spectroscopy measurements. A good correlation has been identified between the microstructural and gas sensing properties of these prepared sensors. Out of these films, 1% PAni doped SnO 2 sensor showed high sensitivity towards NO 2 gas along with a sensitivity of 3.01 × 102 at 40°C for 10 ppm of gas. On exposure to NO 2 gas, resistance of all sensors increased to a large extent, even greater than three orders of magnitude. These changes in resistance upon removal of NO 2 gas are found to be reversible in nature and the prepared composite film sensors showed good sensitivity with relatively faster response/recovery speeds.

A Novel Tungsten Trioxide Based Gas Sensor for Indoor Formaldehyde Detection

2021 ◽  
Vol 16 (3) ◽  
pp. 363-367
Author(s):  
Gaoqi Zhang ◽  
Fan Zhang ◽  
Kaifang Wang ◽  
Tao Tian ◽  
Shanyu Liu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Gas Sensor ◽  
Indoor Air ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Gas Response

Accurate and real-time detection of formaldehyde (HCHO) in indoor air is urgently needed for human health. In this work, a ceramic material (WO3·H2O) with unique structure was successfully prepared using an efficient hydrothermal method. The crystallinity, morphology and microstructure of the as-prepared sensing material were analyzed by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) as well as transmission electron microscope (TEM). The characterization results suggest that the as-prepared sample is composed of square-like nanoplates with uneven surface. Formaldehyde vapor is utilized as the target gas to investigate gas sensing properties of the synthesized novel nanoplates. The testing results indicate that the as-fabricated gas sensor exhibit high gas response and excellent repeatability to HCHO gas. The response value (Ra/Rg) is 24.5 towards 70 ppm HCHO gas at 350 °C. Besides, the gas sensing mechanism was described.

scholarly journals The Role of ALD-ZnO Seed Layers in the Growth of ZnO Nanorods for Hydrogen Sensing

Micromachines ◽  
2019 ◽  
Vol 10 (7) ◽  
pp. 491 ◽  
Author(s):  
Yangming Lu ◽  
Chiafen Hsieh ◽  
Guanci Su
Keyword(s):  
Zinc Oxide ◽  
Surface Area ◽  
Gas Sensing ◽  
Zno Nanorods ◽  
Clean Energy ◽  
Hydrogen Sensor ◽  
Zno Films ◽  
Hydrogen Sensing ◽  
Highly Sensitive ◽  
Seed Layers

Hydrogen is one of the most important clean energy sources of the future. Because of its flammability, explosiveness, and flammability, it is important to develop a highly sensitive hydrogen sensor. Among many gas sensing materials, zinc oxide has excellent sensing properties and is therefore attracting attention. Effectively reducing the resistance of sensing materials and increasing the surface area of materials is an important issue to increase the sensitivity of gas sensing. Zinc oxide seed layers were prepared by atomic layer deposition (ALD) to facilitate the subsequent hydrothermal growth of ZnO nanorods. The nanorods are used as highly sensitive materials for sensing hydrogen due to their inherent properties as oxide semiconductors and their very high surface areas. The low resistance value of ALD-ZnO helps to transport electrons when sensing hydrogen gas and improves the sensitivity of hydrogen sensors. The large surface area of ZnO nanorods also provides lots of sites of gas adsorption which also increases the sensitivity of the hydrogen sensor. Our experimental results show that perfect crystallinity helped to reduce the electrical resistance of ALD-ZnO films. High areal nucleation density and sufficient inter-rod space were determining factors for efficient hydrogen sensing. The sensitivity increased with increasing hydrogen temperature, from 1.03 at 225 °C, to 1.32 at 380 °C after sensing 100 s in 10,000 ppm of hydrogen. We discuss in detail the properties of electrical conductivity, point defects, and crystal quality of ALD-ZnO films and their probable effects on the sensitivity of hydrogen sensing.

A Formaldehyde Gas Sensor Based on Zinc Doped Lanthanum Ferrite

2013 ◽  
Vol 873 ◽  
pp. 304-310 ◽  
Author(s):  
Jin Zhang ◽  
Yu Min Zhang ◽  
Chang Yi Hu ◽  
Zhong Qi Zhu ◽  
Qing Ju Liu
Keyword(s):  
Gas Sensing ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Lanthanum Ferrite ◽  
Gas Sensing Properties ◽  
Recovery Times ◽  
Response And Recovery ◽  
Sensing Characteristics

The gas-sensing properties of zinc doped lanthanum ferrite (Zn-LaFeO3) compounds for formaldehyde were investigated in this paper. Zn-LaFeO3 powders were prepared using sol-gel method combined with microwave chemical synthesis. The powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The formaldehyde gas-sensing characteristics for the sample were examined. The experimental results indicate that the sensor based on the sample Zn-LaFeO3 shows excellent gas-sensing properties to formaldehyde gas. At the optimal operating temperature of 250°C, the sensitivity of the sensor based on LaFe0.7Zn0.3O3 to 100ppm formaldehyde is 38, while to other test gases, the sensitivity is all lower than 20. The response and recovery times for the sample to formaldehyde gas are 100s and 100s, respectively.

Luminescent properties of Y2O3:Eu3+ nanophosphor prepared from urea added precursor using flame spray pyrolysis

2009 ◽  
Vol 24 (8) ◽  
pp. 2584-2588 ◽  
Author(s):  
Jae Seok Lee ◽  
Se Jin Kim ◽  
Tae Kon Kim ◽  
Rajiv K. Singh ◽  
Madhav B. Ranade
Keyword(s):  
Electron Microscopy ◽  
Spray Pyrolysis ◽  
Red Light ◽  
Luminescent Properties ◽  
Flame Spray Pyrolysis ◽  
Cubic Phase ◽  
Flame Spray ◽  
X Ray Diffraction ◽  
Synthesis Conditions ◽  
Transmission Electron

Y2O3:Eu3+ nanophosphor was synthesized by flame spray pyrolysis (FSP) from urea added nitrate based liquid precursor. In this study, urea serves as fuel and subsequently provides additional heat in the flame zone during the synthesis of phosphor particles. The end product shows cubic phase Y2O3:Eu3+ nanophosphor successfully prepared by FSP without heat treatment. The influence of synthesis conditions such as different mol of urea and nitrate source materials in aqueous solution, and doping concentration on luminescent properties, were investigated. The characteristics of nanophosphor such as crystallinity and morphology under various experiments of conditions were carried out by x-ray diffraction (XRD) and field emission-scanning electron microscopy (FE-SEM). The particle size of product was found to be in the range of 20–30 nm from transmission electron microscopy (TEM). In photoluminescence (PL) properties, Y2O3:Eu3+ nanophosphor emitted red light with a peak wavelength of 609 nm when excited with 398 nm wavelength photons.

Visible-Range Luminescence Study in Indium Oxide Nanowires

2007 ◽  
Vol 1010 ◽  
Author(s):  
Davide Calestani ◽  
Mingzheng Zha ◽  
Margherita Mazzera ◽  
Laura Lazzarini ◽  
Andrea Zappettini ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Visible Range ◽  
Silicon Substrates ◽  
Thermal Treatments ◽  
X Ray Diffraction ◽  
Oxide Nanowires ◽  
Fundamental Properties ◽  
Transmission Electron ◽  
Temperature Spectra

AbstractThe interest in semiconducting metal oxide nanowires for gas sensing devices is today very high. Besides common materials such as SnO2 or ZnO, also In2O3 has been obtained in this quasi-1D morphology . In the present work In2O3 nanowires have been grown by vapor transport process starting from 6N pure In. For a better knowledge of the fundamental properties and the sensing mechanism of In2O3 nanowires, the obtained samples have been investigated by different techniques, focusing mainly on the optical characterization. Their morphology and structure have been studied by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and X-Ray diffraction. The optical properties have been investigated as well, mainly by means of photo- (PL) and Cathodo-luminescence (CL) both applied in the UV-Visible range. A complex emission spectrum has been revealed and assigned to specific defects thanks to a deep analysis of the bands as functions of temperature (varying from 20 to 300K) and to suitable thermal treatments (in oxygen rich atmosphere at 1000°C). Moreover, the effects of electron beam irradiation have been pointed out by performing CL spectra on a single In2O3 nanowire after different irradiation times. The possible influence of the substrate has been verified by measuring low temperature spectra on In2O3 nanowires grown both on alumina and silicon substrates.

scholarly journals Liquid petroleum gas sensing performance enhanced by CuO modification of nanocrystalline ZnO-TiO2

2016 ◽  
Vol 34 (3) ◽  
pp. 571-581
Author(s):  
R.B. Pedhekar ◽  
F.C. Raghuwanshi ◽  
V.D. Kapse
Keyword(s):  
Thick Film ◽  
Gas Sensing ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Transmission Electron ◽  
Liquid Petroleum Gas ◽  
Synthesized Materials ◽  
Sensing Characteristics

AbstractNanocrystalline ZnO-TiO2 (with molar ratios 9:1, 7:3, 1:1, 3:7 and 1:9) were successfully synthesized by hydrothermal method. Synthesized materials were examined with the help of X-ray diffraction and transmission electron microscope. Liquid petroleum gas sensing characteristics of the ZnO-TiO2 films were investigated at different operating temperatures. The ZnO-TiO2 thick film (with 1:1 molar ratio) exhibited good response toward liquid petroleum gas as compared to other investigated compositions. Further, liquid petroleum gas sensing characteristics of CuO modified ZnO-TiO2 thick films were investigated. 0.2 M CuO modified ZnO-TiO2 thick film exhibited excellent liquid petroleum gas sensing characteristics such as higher response (~ 1637.49 at 185 °C) with quick response time (~30 s), low recovery time (~70 s), excellent repeatability and stability at low operating temperature.

Sign in / Sign up

Export Citation Format

Share Document