scholarly journals Elastomer Spacers in Fire Conditions

2017 ◽  
Vol 26 (3) ◽  
pp. 109-119
Author(s):  
Paweł Roszkowski ◽  
Bartłomiej Sędłak ◽  
Paweł Sulik
Keyword(s):  
Thermal Degradation ◽  
Fire Resistance ◽  
Load Capacity ◽  
Combustible Material ◽  
Cavity Depth ◽  
Standard Fire ◽  
Degradation Rates ◽  
In Fire ◽  
Resistance Performance ◽  
Fire Conditions

Abstract In the paper, fire resistance of linear joints seal made of elastomer spacers under standard fire conditions, and thermal degradation range of EPDM elastomeric spacers are investigated. The geometry of elastomer spacer joints is important not only for their load capacity under normal conditions - thickness, width, and cavity depth can also influence fire resistance performance. Linear joints of different thicknesses and widths have been tested. The fire insulation and fire integrity were verified for various arrangements. Relatively low thermal degradation rates have been measured, given that EPDM is a combustible material.

scholarly journals FIRE RESPONSES AND RESISTANCE OF CONCRETE-FILLED STEEL TUBULAR FRAME STRUCTURES

2010 ◽  
Vol 10 (02) ◽  
pp. 253-271 ◽  
Author(s):  
MIN YU ◽  
XIAOXIONG ZHA ◽  
JIANQIAO YE ◽  
YI Li
Keyword(s):  
Finite Element ◽  
Fire Resistance ◽  
Load Capacity ◽  
Element Model ◽  
Dynamic Responses ◽  
Frame Structures ◽  
Steel Beams ◽  
Standard Fire ◽  
Cfst Columns ◽  
In Fire

This paper presents the results of dynamic responses and fire resistance of concrete-filled steel tubular (CFST) frame structures in fire conditions by using the nonlinear finite element method. Both strength and stability criteria are considered in the collapse analysis. The frame structures are constructed with circular CFST columns and steel beams of I-sections. In order to validate the finite element solutions, the numerical results are compared with those from a fire resistance test on CFST columns. The finite element model is then adopted to simulate the behavior of frame structures in fire. The structural responses of the frames, including the critical temperature and fire-resisting limit time, are obtained for the ISO-834 standard fire. Parametric studies are carried out to show their influence on the load capacity of the frame structures in fire. Suggestions and recommendations are presented for possible adoption in future construction and design of similar structures.

Study on the Data-Bases for Fire Engineering Design of Structural Steels Members

2012 ◽  
Vol 628 ◽  
pp. 156-160
Author(s):  
In Kyu Kwon ◽  
Hyung Jun Kim ◽  
Heung Youl Kim ◽  
Bum Yean Cho ◽  
Kyung Suk Cho
Keyword(s):  
Bearing Capacity ◽  
Fire Resistance ◽  
Engineering Method ◽  
Fire Tests ◽  
Structural Members ◽  
Data Bases ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
In Fire ◽  
Resistance Performance

Structural steel has been used since the early 1970’s in Korea as primary structural members such as columns, beams, and trusses. The materials have much higher strength such as fast construction, high load bearing capacity, high construction quality but those have a fatal weakness as well. Load-bearing capacity is going down when the structural members are contained in fire condition. Therefore, to protect the structural members made of steels from the heat energy the fire resistance performance required. Generally, the fire resistance performance have evaluated from the exact fire tests in fire furnaces. But the evaluation method takes much more time and higher expenses so, the engineering method requires. The engineering method not only adopts a science but also an engineering experience. In this paper, to make various data-bases for evaluation of structural members such as columns(H-section, RHS), beams, loaded fire tests were conducted and derived not only each limiting temperature but also fire resistance respectively.

Drywall Thermal Properties Exposed to High Temperatures and Fire Condition

2013 ◽  
Vol 62 (1) ◽  
Author(s):  
Md Azree Othuman Mydin
Keyword(s):  
Thermal Properties ◽  
High Temperatures ◽  
Fire Resistance ◽  
Residential Buildings ◽  
Cost Effective ◽  
Standard Fire ◽  
Performance Requirements ◽  
Cost Effective Technique ◽  
Fire Barrier ◽  
In Fire

Drywall is a widespread fire barrier used in house and general building construction. Drywall partitions and ceiling membranes are possibly the most common fire resistant construction approach employed in an extensive range of building types. The utilization of drywall board as prime fire protection of light-flame wood or steel construction is ubiquitous. Drywall board based systems are among those now broadly used, as walls or ceilings and it is principally employed as lining material in light-weight construction, which is a competent and cost effective technique of providing flexible partitioning assemblies in commercial and residential buildings. The thickness of the drywall board lining and the configuration of the framing can be flexibly changed to meet specified fire performance requirements. The use of such systems is increasing every day and there demands to be more research on their properties and behaviour. This paper will presents the properties of drywall board which will includes the assemblies and standard fire tests and the thermal properties of drywall in general and includes suggested properties of drywall by different researchers. Drywall boards shrink and crack at high temperatures, and this leads to collapse of parts of the drywall boards in fire. Fall-off of gypsum in fire affects the fire resistance of the assembly considerably, and cannot be overlooked when evaluating the fire resistance of drywall assemblies

Fire resistance performance of steel composite hollow RC column with inner tube under ISO 834 standard fire

2014 ◽  
Vol 15 (4) ◽  
pp. 543-555 ◽  
Author(s):  
Deok Hee Won ◽  
Woo Sun Park ◽  
In-Sung Jang ◽  
Sang-Hun Han ◽  
Taek Hee Han
Keyword(s):  
Fire Resistance ◽  
Rc Column ◽  
Standard Fire ◽  
Steel Composite ◽  
Resistance Performance

Comparison Study of Structural Stabilities for H-Section Columns Built with Ordinary Grade Strength Structural Steels According to Boundary Conditions and Lengths at High Temperature

2014 ◽  
Vol 937 ◽  
pp. 424-427
Author(s):  
In Kyu Kwon
Keyword(s):  
Boundary Condition ◽  
High Temperature ◽  
Boundary Conditions ◽  
Fire Resistance ◽  
Structural Steels ◽  
Structural Members ◽  
Steel Buildings ◽  
Standard Fire ◽  
Fire Curve ◽  
Resistance Performance

Fire resistance performance of structural members has been evaluated from each singular section and standard fire curve since the beginning of fire tests. However, the need of the exact fire resistance of H-section columns applied in the steel buildings has increased. The main reason for this is there is a difference between the conditions being conducted during the fire test and that from real situation. In this paper, the structural stability of H-section column made of an ordinary strength grade structural steels, SS 400, SM 400, and SM 490 at high temperature were evaluated and compared with boundary conditions and column’s length. This was done in order to suggest a new guideline for the application of fire protective materials in steel column in which the boundary conditions and column lengths are different from that tested with hinge to hinge and 3500 mm. The findings from this study showed hinge to hinge boundary condition was more conservative. And fire resistance performance of longer columns in the case of hinge to fixed and fixed to fixed boundary condition than from 3500 mm and hinge to hinge boundary condition can sustain at high temperature without adding fire protective materials.

Behaviour of steel frames under fire conditions

1999 ◽  
Vol 26 (2) ◽  
pp. 156-167 ◽  
Author(s):  
D I Nwosu ◽  
VKR Kodur
Keyword(s):  
Fire Resistance ◽  
Steel Frames ◽  
Load Ratio ◽  
Steel Structures ◽  
Point Of View ◽  
Frame Structures ◽  
Structural Behaviour ◽  
Analysis And Design ◽  
In Fire ◽  
Fire Conditions

A state-of-the-art review of the behaviour of steel frame structures in fire is presented. Results from different studies indicate that the behaviour of a complete structure is different from that of a single structural member under fire conditions from the point of view of fire resistance. Earlier studies also show that analysis and design of steel structures against fire based on their overall behaviour could lead to a reduction or the elimination of applied fire protection to certain structural members. The effects of continuity, restraint conditions, and load ratio on the fire resistance of frame structures are discussed. The beneficial aspects derived from considering overall structural rather than single-member behaviour in fire are illustrated through the analysis on two one-bay, one-storey, unprotected steel portal frames, a column, and a beam. Also comparison is made between the performance of a beam with different end restraints in fire. Results from the analyses indicate that the fire resistance of a member is increased when it is considered as part of a structure compared with when it is considered as a single member.Key words: steel, frames, fire resistance, buckling, loads, overall structural behaviour.

Study on Estimate of Load Ratio of Doubly Reinforced Concrete Beam Exposed to the Standard Fire

2017 ◽  
Vol 737 ◽  
pp. 465-470
Author(s):  
Jae Hong An ◽  
In Hwan Yeo ◽  
Ki Soo Jeon ◽  
Ki Ho In
Keyword(s):  
South Korea ◽  
Fire Resistance ◽  
Concrete Beam ◽  
Load Ratio ◽  
Reinforced Concrete Beam ◽  
High Rise ◽  
Standard Fire ◽  
Loading Ratio ◽  
Resistance Performance ◽  
Reinforcement Beam

There are a lot of concerns on safety structure performance by being buildings to be large and high-rise. In particular, damage due to the fire recently leads to a large disaster and therefore a variety of countries operate the regulation on the fire resistance performance depending on the building structure. There are differences on the fire resistance design in each country but 50% of the design load is suggested to be reasonable for the normal temperature during the fire by applying the concept of the loading ratio to the fire resistance design of structures. Since the loading ratio is the factor having a major impact on the evaluation of the fire resistance performance, it should be preferentially considered. The study on setting up the loading ratio to evaluate the fire resistance performance and safety of structures has yet to be fully furnished in South Korea. Therefore, in this paper, the loading ratio proper for the construction status in South Korea is to be taken into account and then the ratio is to be proposed on the single reinforcement beam.

Fire Resistance Evaluation of Reinforced Concrete Columns Using Axial Load Ratio and Slenderness Ratio

2014 ◽  
Vol 905 ◽  
pp. 268-272
Author(s):  
In Hwan Yeo ◽  
Bum Yean Cho ◽  
Jae Hong An ◽  
Byung Youl Min
Keyword(s):  
Fire Resistance ◽  
Axial Load ◽  
Slenderness Ratio ◽  
Load Ratio ◽  
Cost Effective ◽  
Concrete Columns ◽  
Accurate Estimation ◽  
Structural Members ◽  
Standard Fire ◽  
Resistance Performance

Since the column members in buildings deal with both vertical and horizontal loads, appropriated amount of load should be estimated in order to evaluate the fire resistance performance of the columns under loaded condition. However, according to the ISO 834, the international standard for the evaluation of structural members, the fire resistance performance evaluation of column members is only based on the displacement and displacement rate under loaded condition in a standard fire. The purpose of this study is to suggest appropriate axial load ratios for the evaluation of fire resistance performance. The test conducted in this study produced appropriate axial load ratios for different slenderness ratios. They are expected to contribute to more accurate estimation of fire resistance performance and more efficient and cost-effective structural design.

scholarly journals Analytical study on lateral torsional buckling of partially encased beams under ISO834 fire exposure

Fire Research ◽  
2016 ◽  
Author(s):  
Ana Belén Ramos-Gavilán ◽  
Paulo Piloto ◽  
Luís Mesquita
Keyword(s):  
Fire Resistance ◽  
Experimental Tests ◽  
Reduction Factor ◽  
Lateral Torsional Buckling ◽  
Torsional Buckling ◽  
Standard Fire ◽  
Resistance Moment ◽  
The Moment ◽  
In Fire ◽  
Simplified Calculation

European standard EN1994-1-2:2005 provides tabulated values and simplified calculation models for assessing fire resistance of composite beams, but does not consider the design checks against lateral torsional buckling under fire. This research presents an analytical method to calculate the buckling resistance moment of laterally unrestrained partially encased beams in fire conditions. The proposal applies a reduction factor for lateral torsional buckling in fire design condition to the moment resistance of the homogenised section at time t, determined by EN1994-1-2:2005. Two finite element models capable to simulate the thermal and mechanical behaviour of partially encased beams are also presented, including the validation against fire tests conducted by Piloto et al. Based on these models, a numerical analysis of partially encased beams with the same geometry and material properties as used in experimental tests is presented, evaluating different load levels when exposed to standard fire ISO834:1999. The numerical results of fire resistance according to standard EN1363- 1:2012 and the numerical ultimate time, when beams suffer instability, are used to validate the proposal, using experimental and analytical heating result according to EN1994-1-2:2005.

Sign in / Sign up

Export Citation Format

Share Document