Influence of atmospheric pressure plasma treatments on the surface properties of ligno-cellulosic substrates

Holzforschung ◽  
2016 ◽  
Vol 70 (1) ◽  
pp. 55-61 ◽  
Author(s):  
William P. Lekobou ◽  
Karl R. Englund ◽  
Marie-Pierre Laborie ◽  
Patrick D. Pedrow
Keyword(s):  
Surface Properties ◽  
Atmospheric Pressure ◽  
Wood Flour ◽  
Capillary Rise ◽  
Treated Wood ◽  
Atmospheric Pressure Plasma ◽  
Contact Angles ◽  
Water Contact ◽  
Weakly Ionized ◽  
Metallic Mesh

AbstractThe paper aims at the investigation of atmospheric pressure weakly ionized plasmas with argon and acetylene to deposit plasma-polymerized coatings on wood veneers (birch, maple), cellulose paper, and pine wood flour to modify their surface properties, in particular their topography and wettability. The treatment was performed in a reactor containing an array of high-voltage needles and a grounded metallic mesh as electrodes. The deposition occurred in the discharge downstream of the plasma region. The plasma-polymerized acetylene deposits form spherical nodules on the surface of the substrates and change their wettability from hydrophilic to hydrophobic. The water contact angles of the veneer were determined with a goniometer. The capillary rise was combined with the Washburn equation to assess the change in hydrophilicity of the plasma-treated wood flour.

Surface modifications of wood materials using atmospheric pressure corona-based weakly ionized plasma

2017 ◽  
Vol 31 (7) ◽  
pp. 946-958 ◽  
Author(s):  
Rokibul Islam ◽  
Shuzheng Xie ◽  
William Lekobou ◽  
Karl Englund ◽  
Patrick Pedrow
Keyword(s):  
Ponderosa Pine ◽  
Atmospheric Pressure ◽  
Wood Flour ◽  
Capillary Rise ◽  
Treated Wood ◽  
Wood Fibers ◽  
Post Discharge ◽  
Dielectric Barriers ◽  
Weakly Ionized ◽  
Weakly Ionized Plasma

Enhanced atmospheric pressure corona-based weakly ionized plasma was investigated to modify surface properties of wood materials. The plasma was generated using a point-to-point bare electrode geometry without dielectric barriers. The gas-phase admixture used in this work was argon and acetylene. Wood fibers were processed in the post-discharge region outside of the harsh corona environment. Return corona emanating into the high-voltage gap from the grounded screen was utilized to effectively activate acetylene molecules near the substrate. Scanning electron microscopy was used to study the surface morphology of the treated and untreated substrates. The treated wood material was observed to contain on their surface nano- and micro-nodules of plasma-polymerized acetylene. Capillary rise measurements confirmed changes in the surface wettability of the substrates. The water capillary rise rate and diffusion coefficient were reduced by about 37% and 57%, respectively, for a 15-min treatment of ponderosa pine wood flour.

scholarly journals In Situ Surface Modification of Paper-Based Relics with Atmospheric Pressure Plasma Treatment for Preservation Purposes

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 786
Author(s):  
Xu Yan ◽  
Guo-Sai Liu ◽  
Jing Yang ◽  
Yi Pu ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Atmospheric Pressure Plasma ◽  
Good Method ◽  
Contact Angles ◽  
Water Penetration ◽  
Water Contact ◽  
Pressure Plasma ◽  
Static Water

Paper-based relics, which are an important part of cultural heritage worldwide, are at risk of imminent damage from various environmental sources. To protect them, the atmospheric pressure plasma polymerization of hexamethyldisiloxane (HMDSO) precursor has been explored on paper-based relics in situ. The macro and micro images taken during this process suggest that the in situ plasma treatment does not change the macro morphology and the micro structure of the treated paper-based relic samples. On the other hand, plasma treatment causes the polymerization of the HMDSO which then produces nanoparticles deposited onto the paper-based relics. These nanoparticles provide good waterproof properties with large static water contact angles and smaller rolling angles, which protect the paper-based relics from water penetration. Moreover, since the nanoparticles are deposited onto the fibers, waterproof fastness is ensured. Also, the examined mechanical properties of the treated and untreated paper-based relics indicate that the atmospheric pressure plasma treatment does not affect the strength of the paper very much. The results in this study show that atmospheric pressure plasma treatment with the use of HMDSO precursor is a good method to preserve paper-based relics.

Effects of green technology plasma pre-treatment on the wettability and ink adhesion of paper

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Samed Ayhan Özsoy ◽  
Safiye Meriç Acıkel ◽  
Cem Aydemir
Keyword(s):  
Contact Angle ◽  
Plasma Treatment ◽  
Surface Properties ◽  
Atmospheric Pressure ◽  
Atmospheric Pressure Plasma ◽  
Contact Angles ◽  
Content Type ◽  
Surface Energies ◽  
Pressure Plasma ◽  
Plasma Device

Purpose The surface energy of the printing material can be increased to desired levels with different chemicals or methods. However, the important thing is that the surface properties of printing material are not affected negatively. In this way the aim of this paper provide that the surface properties of matte and glossy coated paper is improved by the argon containing atmospheric pressure plasma device because the plasma treatment method does not occur surface damaging on the papers. Design/methodology/approach In experimental studies, test samples cut from 160 mm × 30 mm in size from 115 g/m2 gloss- and matt-coated papers were used. The plasma treatments of paper samples were carried out with an argon containing atmospheric pressure plasma device of laboratory scale that produces plasma of the corona discharge type at radio frequency. The optimized plasma parameters were at a frequency of 20 kHz and plasma power 200 W. A copper electrode of length 12 cm and diameter 2.5 mm was placed in the centre of the nozzle. Findings Research findings showed that the surface energies of the papers increased with the increase in plasma application time. While the contact angle of the untreated glossy paper is 82.2, 8 second plasma applied G3 sample showed 54 contact angle value. Similarly, the contact angle of the base paper of matt coated is 91.1, while M3 is reduced to 60.4 contact angles by the increasing plasma time. Originality/value Plasma treatment has shown that no chemical coating is needed to increase the wettability of the paper surface by reducing the contact angle between the paper and the water droplet. In addition, the surface energies of all papers treated by argon gas containing atmospheric pressure plasma, increased. Plasma treatment provides to improve both the wettability of the paper and the adhesion property required for the ink, with an environmentally friendly approach.

scholarly journals Surface Properties of Pine Scrimber Panels with Varying Density

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 397 ◽  
Author(s):  
Jinguang Wei ◽  
Qiuqin Lin ◽  
Yahui Zhang ◽  
Wenji Yu ◽  
Chung-Yun Hse ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Photoelectron Spectroscopy ◽  
Lower Surface ◽  
Contact Angles ◽  
High Density ◽  
Water Contact ◽  
Change Rate ◽  
Hydrophilic Material ◽  
Wood Grain

Coating quality for scrimber products against exterior conditions is largely dependent on the surface properties. The wettability, morphology, and chemical composition of pine scrimber surfaces were investigated to better understand the surface properties. The scrimber was found to be a hydrophilic material because the water contact angles were less than 90°. The panels with a density of 1.20 g/cm3 had the largest angle change rate (k = 0.212). As the panel density increased, the instantaneous contact angle of each test liquid (i.e., water, formamide, and diiodomethane) on the panels decreased, and so did surface free energy. Panels with higher density showed lower surface roughness. Surface roughness across the wood grain was greater than that along the grain. SEM observations showed the high-density panels had a smoother surface with fewer irregular grooves in comparison with the low-density panels. X-ray photoelectron spectroscopy (XPS) analysis indicated that more unoxygenated groups appeared on the surface of high-density panels.

scholarly journals Synthesis and Properties of Plasma-Polymerized Methyl Methacrylate via the Atmospheric Pressure Plasma Polymerization Technique

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 396 ◽  
Author(s):  
Choon-Sang Park ◽  
Eun Jung ◽  
Hyo Jang ◽  
Gyu Bae ◽  
Bhum Shin ◽  
...  
Keyword(s):  
Methyl Methacrylate ◽  
Photoelectron Spectroscopy ◽  
Atmospheric Pressure ◽  
Secondary Ion Mass Spectrometry ◽  
Atmospheric Pressure Plasma ◽  
Thickness Measurement ◽  
Water Contact ◽  
Pressure Plasma ◽  
Measurement Results ◽  
The Fourier Transform

Pinhole free layers are needed in order to prevent oxygen and water from damaging flexible electrical and bio-devices. Although polymerized methyl methacrylate (polymethyl methacrylate, PMMA) for the pinhole free layer has been studied extensively in the past, little work has been done on synthesizing films of this material using atmospheric pressure plasma-assisted electro-polymerization. Herein, we report the synthesis and properties of plasma-PMMA (pPMMA) synthesized using the atmospheric pressure plasma-assisted electro-polymerization technique at room temperature. According to the Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and time of flight-secondary ion mass spectrometry (ToF-SIMS) results, the characteristic peaks from the pPMMA polymer chain were shown to have been detected. The results indicate that the percentage of hydrophobic groups (C–C and C–H) is greater than that of hydrophilic groups (C–O and O–C=O). The field emission-scanning electron microscope (FE-SEM) and thickness measurement results show that the surface morphology is quite homogenous and amorphous in nature, and the newly proposed pPMMA film at a thickness of 1.5 µm has high transmittance (about 93%) characteristics. In addition, the results of water contact angle tests show that pPMMA thin films can improve the hydrophobicity.

Tailoring Surface Properties of Nonwoven Polypropylene by Cyclonic Atmospheric Pressure Plasma

2014 ◽  
Vol 42 (12) ◽  
pp. 3668-3673
Author(s):  
Ching-Yuan Tsai ◽  
Ta-Chin Wei ◽  
Ko-Shao Chen ◽  
Ruey-Shin Juang ◽  
Chun Huang
Keyword(s):  
Surface Properties ◽  
Atmospheric Pressure ◽  
Atmospheric Pressure Plasma ◽  
Pressure Plasma
Sign in / Sign up

Export Citation Format

Share Document