Potential Catalysts for the Acetylation of Wood

Holzforschung ◽  
2000 ◽  
Vol 54 (3) ◽  
pp. 269-272 ◽  
Author(s):  
C.A.S. Hill ◽  
N.S. Cetin ◽  
N. Ozmen
Keyword(s):  
Acetic Anhydride ◽  
Tertiary Amine ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Effective Catalyst ◽  
Rate Of Reaction ◽  
Influence Of Substrate ◽  
Uncatalysed Reaction ◽  
Amine Catalysts

Summary The potential of several tertiary amine catalysts (pyridine, 4-dimethyl-amino pyridine, N-methyl pyrrolidine and N-methyl pyrrolidinone) for the acetylation of Corsican pine sapwood, using acetic anhydride, has been investigated. Rates of reaction were compared with non-catalysed acetylation using acetic anhydride. The hypernucleophile 4-dimethylamino pyridine was found to be the most effective catalyst of those studied. At a concentration of only 1% of the catalyst in acetic anhydride, a weight percent gain of 20% was realised, compared with 7% for the uncatalysed reaction, after 30 minutes system at 100°C. The influence of substrate swelling upon the rate of reaction with wood is discussed.

scholarly journals Acetylation of Wood Flour from Four Wood Species Grown in Nigeria Using Vinegar and Acetic Anhydride

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Yakubu Azeh ◽  
Gabriel Ademola Olatunji ◽  
Cheku Mohammed ◽  
Paul Andrew Mamza
Keyword(s):  
Acetic Anhydride ◽  
Wood Species ◽  
Wood Flour ◽  
Beech Wood ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Adansonia Digitata ◽  
Lignocellulosic Fibers ◽  
Ft Ir ◽  
African Locust Bean

Effect of acetylation on pretreated wood flour of four different wood species, Boabab (Adansonia digitata), Mahoganny (Daniella oliveri), African locust bean (Parkia biglobosa) and Beech wood (Gmelina arborea), had been investigated. The first batch of wood species were acetylated using acetic anhydride while the second batch were acetylated with commercial vinegar. Both experiments were conducted in the presence of varying amount of CaCl2 as catalyst and at temperature of 120°C for 3 h. The success of acetylation was determined based on Weight Percent Gain for each sample treated with either chemicals used. FT-IR, a veritable tool was used for the analysis of both treated and untreated samples to further investigate the success of acetylation. The results showed the presence of important band such as carbonyl absorptions at 1743, 1744, 1746, 1731, 1718 and 1696 cm−1 as appeared separately in the spectra of acetylated samples, confirming esterification occurred. The purpose of this work was to investigate the applicability of vinegar for acetylation of lignocellulosic fibers. Blends/composites were prepared by solution casting and their kinetics investigated in distilled water. The results indicated they could be used in outdoor applications such as, decking and packaging.

N-Bromosuccinimide (NBS) – an efficient catalyst for acetylation of wood

Holzforschung ◽  
2016 ◽  
Vol 70 (5) ◽  
pp. 421-427 ◽  
Author(s):  
Giridhar B. Nagarajappa ◽  
Krishna K. Pandey ◽  
Aniket S. Shinde ◽  
Hosadu M. Vagdevi
Keyword(s):  
Reaction Time ◽  
Acetic Anhydride ◽  
Dimensional Stability ◽  
Catalyst Concentration ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Reaction Conditions ◽  
Hydrophobic Properties ◽  
Efficient Catalyst ◽  
C Nmr

Abstract Solvent-free acetylation of rubberwood (Hevea brasiliensis Müll.Arg) with acetic anhydride (Ac2O) and by means of N-bromosuccinimide (NBS) as catalyst was carried out in an oil bath at 105°C and 120°C. The effect of catalyst concentration, temperature, and reaction time was studied. The extent of acetylation was measured by determining the weight percent gain (WPG), and the acetylated wood was characterized by FTIR-ATR, CP/MAS 13C NMR, and XRD spectroscopy. The presence of NBS in concentrations between 1.0% and 3.0% elevated the acetylation rate to a great extent. WPG increased from 8.1% without catalyst to 22.1% for 2% NBS concentration after 60 min reaction at 120°C. Similarly, after 60-min reaction time at 105°C, WPG with 3% NBS concentration was 19.0% compared to 7.6% with un-catalyzed reaction under the same reaction conditions. The effect of microwave heating (MWh) on the NBS-catalyzed acetylation was also investigated. A significant level of modification was achieved within a few minutes of MWh. The hydrophobic properties and dimensional stability of the acetylated wood were elevated. NBS was found to be an effective catalyst for wood acetylation.

scholarly journals Effect of Furfurylation on Hierarchical Porous Structure of Poplar Wood

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 32
Author(s):  
Xiaoshuang Shen ◽  
Pan Jiang ◽  
Dengkang Guo ◽  
Gaiyun Li ◽  
Fuxiang Chu ◽  
...  
Keyword(s):  
Porous Structure ◽  
Value Added ◽  
Untreated Wood ◽  
Weight Percent Gain ◽  
Wood Properties ◽  
Weight Percent ◽  
Acoustic Properties ◽  
Hierarchical Porous Structure ◽  
Wood Processing ◽  
Hierarchical Porous

Some wood properties (such as permeability and acoustic properties) are closely related to its hierarchical porous structure, which is responsible for its potential applications. In this study, the effect of wood impregnation with furfuryl alcohol on its hierarchical porous structure was investigated by microscopy, mercury intrusion porosimetry and nuclear magnetic resonance cryoporometry. Results indicated decreasing lumina diameters and increasing cell wall thickness of various cells after modification. These alterations became serious with enhancing weight percent gain (WPG). Some perforations and pits were also occluded. Compared with those of untreated wood, the porosity and pore volume of two furfurylated woods decreased at most of the pore diameters, which became more remarkable with raising WPG. The majority of pore sizes (diameters of 1000~100,000 nm and 10~80 nm) of macrospores and micro-mesopores of two furfurylated woods were the same as those of untreated wood. This work could offer thorough knowledge of the hierarchical porous structure of impregnatedly modified wood and pore-related properties, thereby providing guidance for subsequent wood processing and value-added applications.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

Fabrication of highly stable and durable furfurylated wood materials. Part I: process optimization

Holzforschung ◽  
2020 ◽  
Vol 74 (12) ◽  
pp. 1135-1146
Author(s):  
Wanju Li ◽  
Minghui Liu ◽  
Hankun Wang ◽  
Yan Yu
Keyword(s):  
Orthogonal Experiment ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Chinese Fir ◽  
Curing Temperature ◽  
Modulus Of Rupture ◽  
Scale Production ◽  
Range Analysis ◽  
Decay Fungi ◽  
Mold Resistance

AbstractIn order to improve dimensional stability and durability of wood, furfurylation of poplar and Chinese fir wood using newly developed furfuryl alcohol (FA) formulation combined with a common vacuum and pressure impregnation process was studied. An orthogonal experiment was designed to optimize the furfurylation process for the two wood species. The weight percent gain (WPG), equilibrium moisture content (EMC), anti-swelling efficiency (ASE), modulus of rupture (MOR), modulus of elasticity (MOE), as well as resistance to mold, decay fungi, and termites were evaluated. The results showed that nearly all the properties of the furfurylated wood could be improved to various extents. The average ASE of the furfurylated Chinese fir and poplar could reach as high as 80, 71, 92% and 79, 90, 75% in tangential and radial directions, and by volume, respectively, higher than most previously reported wood modification processes. Furthermore, the modified wood had excellent biological durability, with nearly 100% mold resistance, strong decay and termite resistance. Finally, processing parameters with 50% FA, 105–115 °C curing temperature, and 5–8 h curing time were therefore recommended for pilot-scale production of furfurylated poplar and Chinese fir wood based on range analysis.

Surface Modification of Bacterial Cellulose Sheets With Various Fire Retardants

2020 ◽  
Vol 13 (2) ◽  
Author(s):  
Eser Sözen ◽  
Gökhan Gündüz ◽  
Deniz Aydemir ◽  
Ahmet Can
Keyword(s):  
Thermal Stability ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Phosphoric Acid ◽  
Bacterial Cellulose ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Fire Retardants ◽  
Freeze Dried

Abstract This study investigated the effects of various fire retardants including Firetex®, phosphoric acid, and nanoboron nitride on the thermal and morphological properties of bacterial cellulose (BC) sheets. Hestrin and Schramm medium was inoculated with Gluconacetobacter hansenii and the medium with the bacteria was incubated for 14 days. The obtained BC sheets were freeze-dried and then the dried sheets were immersed with Firetex®, phosohoric acid, and nanoboron nitride for a day. The sheets were once again freeze-dried and weight percent gain (WPG) of the sheets was calculated by using wet and dried weights. The morphological characterization, thermal properties, and structural changes of the obtained sheets were also investigated with scanning electron microscopy (SEM), thermogravimetric analysis, and Fourier-transform infrared spectroscopy, respectively. The weight percent gain was found to increase 31% for the samples with boron nitride and 1040% for the samples with phosphoric acid after the impregnation. The thermogravimetric analysis showed that the impregnation improved the thermal stability of the BC films. The sheets with nanoboron nitride exhibited the best thermal stability, whereas the sheets with Firetex were determined to have the worst thermal stability. The Fourier-transform infrared spectroscopy showed some changes in the structural properties of the all BC sheets with fire retardants. As a result, it can be said that nanoboron nitride at low temperatures (25–250 °C) and Firetex and phosphoric acid at higher temperatures (600–900 °C) showed better thermal stability.

Characteristics and thermal decomposition kinetics of wood-SiO2 composites derived by the sol-gel process

Holzforschung ◽  
2017 ◽  
Vol 71 (3) ◽  
pp. 233-240 ◽  
Author(s):  
Ke-Chang Hung ◽  
Jyh-Horng Wu
Keyword(s):  
Activation Energy ◽  
Thermal Decomposition ◽  
Apparent Activation Energy ◽  
Sol Gel ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Decomposition Kinetics ◽  
Thermal Decomposition Kinetics ◽  
Sol Gel Process ◽  
Kinetics Of

Abstract Wood-SiO2 composites (WSiO2Cs) were prepared by means of the sol-gel process with methyltrimethoxysilane (MTMOS) as a reagent, and the physical properties, structure and thermal decomposition kinetics of the composites has been evaluated. The dimensional stability of the WSiO2Cs was better than that of unmodified wood, especially in terms of the weight percent gain (WPG), which achieved values up to 30%. The 29Si-NMR spectra show two different siloxane peaks (T2 and T3), which supports the theory about the formation of MTMOS network structures. Thermal decomposition experiments were also carried out in a TG analyzer under a nitrogen atmosphere. The apparent activation energy was determined according to the iso-conversional methods of Friedman, Flynn-Wall-Ozawa, modified Coats-Redfern, and Starink. The apparent activation energy between 10 and 70% conversion is 147–172, 170–291, 189–251, and 192–248 kJ mol−1 for wood and WSiO2Cs with WPGs of 10, 20, and 30%, respectively. However, the reaction order between 10 and 70% conversion calculated by the Avrami theory was 0.50–0.56, 0.35–0.45, 0.33–0.44, and 0.28–0.48. These results indicate that the dimensional and thermal stability of the wood could be effectively enhanced by MTMOS treatment.

Sign in / Sign up

Export Citation Format

Share Document