scholarly journals Effect of Geotextile Reinforcement on Shear Strength of Sandy Soil: Laboratory Study

2016 ◽  
Vol 38 (4) ◽  
pp. 3-13 ◽  
Author(s):  
Sidali Denine ◽  
Noureddine Della ◽  
Muhammed Rawaz Dlawar ◽  
Feia Sadok ◽  
Jean Canou ◽  
...  
Keyword(s):  
Shear Strength ◽  
Mechanical Behaviour ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Loose Sand ◽  
Test Results ◽  
Compression Tests ◽  
Confining Stress ◽  
Natural Sand ◽  
Confining Pressures

Abstract This paper presents results of a series of undrained monotonic compression tests on loose sand reinforced with geotextile mainly to study the effect of confining stress on the mechanical behaviour of geotextile reinforced sand. The triaxial tests were performed on reconstituted specimens of dry natural sand prepared at loose relative density (Dr = 30%) with and without geotextile layers and consolidated to three levels of confining pressures 50, 100 and 200 kPa, where different numbers and different arrangements of reinforcement layers were placed at different heights of the specimens (0, 1 and 2 layers). The behaviour of test specimens was presented and discussed. Test results showed that geotextile inclusion improves the mechanical behaviour of sand, a significant increase in the shear strength and cohesion value is obtained by adding up layers of reinforcement. Also, the results indicate that the strength ratio is more pronounced for samples which were subjected to low value of confining pressure. The obtained results reveal that high value of confining pressure can restrict the sand shear dilatancy and the more effect of reinforcement efficiently.

A Change of Undrain Shear Strength of Soft Ground during Consolidation Process

2014 ◽  
Vol 513-517 ◽  
pp. 269-272
Author(s):  
Yeong Mog Park ◽  
Ik Joo Um ◽  
Norihiko Miura ◽  
Seung Cheol Baek
Keyword(s):  
Shear Strength ◽  
Soft Clay ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Test Results ◽  
Exponential Equation ◽  
Consolidation Process ◽  
Degree Of Consolidation ◽  
Clay Ground ◽  
Strength Increment

The purpose of this study is to investigate the undrain shear strength increment during consolidation process of soft clayey soils. Thirty kinds of laboratory triaxial tests have been performed using undisturbed and remolded Ariake clay samples with different degree of consolidation and 5 kinds of confining pressure. Test results show that well known linear equation proposed by Yamanouchi et al.(1982) is overestimated the strength of undisturbed soft clay ground in the process of consolidation. A new simple and reasonable exponential equation proposed in this paper.

Experimental Study on Shear Strength Considering Initial Void Ratio and Plasticity Index

2013 ◽  
Vol 405-408 ◽  
pp. 63-67
Author(s):  
Xing Chen Wang ◽  
Ri Qing Xu ◽  
Jian Feng Zhu
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Plasticity Index ◽  
Test Results ◽  
Compression Tests ◽  
Functional Relationships ◽  
Initial Void Ratio

A series of drained triaxial compression tests under different conditions were performed to quantitatively study the influence of the initial void ratio and plasticity index on the shear strength of remolded saturated clays. The test results show that both the peak stress friction angle and peak deviatoric stress decrease with increasing initial void ratio and plasticity index of the soil under the same confining pressure; whereas, they increase with increasing confining pressure of the soil under the same initial void ratio and plasticity index. A new synthesized physical parameter λ, which simultaneously represent both the type and the condition of remolded saturated clays, is defined based on the test results in this work. The functional relationships among the parameters φd and peak deviatoric stress in Mohr-Coulomb equation and the parameter λ are established to develop a modified Mohr-Coulomb equation by considering physical properties of soil. In this equation, only two input parameters, i.e., λ and the confine pressure, are needed to predict the shear strength of the soil. In order to check the accuracy of the proposed equation, laboratory tests were conducted to evaluate against the predicted results. The results show that the peak shear strength of remolded saturated clays can be well described by the proposed equation. Key words: shear strength; Mohr-Coulomb equation; remolded saturated clays; initial void ratio; plasticity index.

scholarly journals Investigation on the relationship between CT numbers and marble failure under different confining pressures

2021 ◽  
Vol 60 (1) ◽  
pp. 846-852
Author(s):  
Yang Yan-Shuang ◽  
Li Kai-Yue ◽  
Zhou Hui ◽  
Tian Hao-Yuan ◽  
Cheng Wei ◽  
...  
Keyword(s):  
Damage Mechanics ◽  
Triaxial Compression ◽  
Ct Scanning ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Compression Tests ◽  
Ct Number ◽  
Confining Pressures ◽  
Loading Tests ◽  
Rock Specimens

Abstract Computed tomography (CT) scanning technology is helpful in investigating rock materials as it can demonstrate the micro structure of rock clearly. Conventional triaxial compression tests and the corresponding graded triaxial loading tests were carried out to investigate the complex failure mechanism of the marble at the Jinping Hydropower Station. After that CT-scanning tests were done on the loaded marble specimens. The test results show that (1) the CT numbers of the specimens have a certain statistical regularity, that is, the CT numbers of the specimens under different confining pressures satisfy the Weibull distribution, as the confining pressure increases, the mean values rise while variances decrease; (2) in the two groups of tests, the average CT numbers corresponding to the conventional triaxial tests are higher than those corresponding to the graded loading tests, but the CT number variances are lower than those of the graded loading tests; and (3) according to meso-damage mechanics, the damage variables of the rock specimens were established based on the definition of CT numbers. The calculation results show that the damage variables decrease with the increase in confining pressure, the damage variables of the rock specimens in the graded loading tests are higher than those in the conventional triaxial test, and the differences between the two loading tests have grown with the increase in confining pressure.

Gravel Content Effect on the Shear Strength of Clay-Gravel Mixtures

2011 ◽  
Vol 71-78 ◽  
pp. 4685-4688 ◽  
Author(s):  
Chen Wang ◽  
Chuan Ni Zhan
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Triaxial Compression ◽  
Constant Strain Rate ◽  
Friction Angle ◽  
Confining Pressure ◽  
Internal Friction Angle ◽  
Compression Tests ◽  
Gravel Content ◽  
Confining Pressures

Gravel content is an important factor affecting the mechanical properties of clay-gravel mixtures. To study the effects of gravel content on the shear strength of clay-gravel mixtures, constant-strain-rate drained triaxial compression tests were conducted for various mixtures. The gravel contents were 30%, 40%, 50% and 70%. The confining pressures were varied from 50kPa to 300kPa. Test results indicate that the deviator stress at failure under the same confining pressure increases with the increase in gravel content. As the gravel content in the mixtures is between 30% and 50%, the shear strength is jointly attributed by clay and gravel. An increase in gravel content results in slight increases in both the cohesion intercept and internal friction angle. At gravel content of up to 70%, the shear strength of the mixture is controlled by that of the gravel, and the cohesion intercept and the internal friction angle increase sharply.

Experimental Study on the In Situ Mechanical Properties of Methane Hydrate-Bearing Sediments

2013 ◽  
Vol 275-277 ◽  
pp. 326-331 ◽  
Author(s):  
Zhong Ming Sun ◽  
Jian Zhang ◽  
Chang Ling Liu ◽  
Shi Jun Zhao ◽  
Yu Guang Ye
Keyword(s):  
Shear Strength ◽  
Methane Hydrate ◽  
Failure Time ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Hydrate Saturation ◽  
Confining Pressures ◽  
Coulomb Failure Criterion ◽  
Hydrate Bearing Sediments

TDR was introduced to solve the problem of how to measure hydrate saturation accurately. Then a series of un-drained triaxial tests were carried out on methane hydrate-bearing sediments under various conditions with effective confining pressures at 1, 2 and 4 MPa, average hydrate saturations at 15.71, 35.7 and 56.49% and strain rate at 0.8%/min. The results indicate that the shear strength increases with the increases of effective confining pressure and hydrate saturation, but the maximum failure time decreases with the increasing effective confining pressures. According to Mohr-Coulomb failure criterion, the shear strength of methane hydrate-bearing sediments was analyzed. It can be found that the internal friction angles are not sensitive to hydrate saturation, but the cohesion shows a high hydrate saturation dependency.

Stress–strain behaviour of weathered weak rock in middle-sized triaxial tests

2006 ◽  
Vol 43 (10) ◽  
pp. 1096-1104 ◽  
Author(s):  
De'an Sun ◽  
Tugen Feng ◽  
Hajime Matsuoka
Keyword(s):  
Triaxial Test ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Weak Rock ◽  
Test Results ◽  
Compression Tests ◽  
Stress Strain ◽  
Strain Behaviour ◽  
Undisturbed Samples ◽  
Strain Relationship

A middle-sized triaxial test apparatus for a specimen 20 cm in height and 10 cm in diameter was developed to measure the deformation and strength of weak rock or gravel. High-quality undisturbed samples of a weathered weak rock were taken from a dam site by a core drilling method. To avoid damage to the structure of the weak rock due to saturation of specimens as a result of measuring volume change through the water change in a burette, the lateral deformation of specimens was directly measured in the unsaturated condition using three rings mounted on the specimen. Using the developed triaxial test apparatus, isotropic compression tests and consolidated–drained triaxial compression tests were performed on unsaturated or saturated undisturbed samples under confining pressures of 49, 98, 196, 392, 539, and 683 kPa. The test results show that the stress–strain relationship of the weathered weak rock under both unsaturated and saturated conditions is strongly influenced by the confining pressure when the confining pressure is less than 392 kPa, and the stress–strain behaviour becomes similar to that of normally consolidated clay when the confining pressure is greater than 392 kPa. Comparison of results of triaxial tests on unsaturated and saturated specimens shows that the saturated samples become somewhat weak. The test results also show that the bonding and stress history largely influence the stress–strain relationship at small strain levels.Key words: weathered weak rock, microstructure, undisturbed sample, deformation, strength, triaxial test, unsaturated sample.

scholarly journals Effects of granular shape on shear modulus and damping ratio of gravel

2019 ◽  
Vol 23 (1) ◽  
pp. 87-91
Author(s):  
Kai Cui ◽  
Hang Sheng
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Strain Amplitude ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Test Results ◽  
Grain Composition ◽  
Confining Pressures ◽  
Shear Strain Amplitude

The effects of the consolidation ratio, effective confining pressure, gravel content, and granule breakage on the shear modulus and damping ratio of gravel have been extensively researched in recent years. However, studies on the effect of the granular shape are rare. Thus, under different confining pressures, dynamic triaxial tests were performed on gravel specimens to investigate the effect of granular shape on the shear modulus and damping ratio of gravel specimens by using a multifunctional triaxial testing instrument. The samples consisted of two kinds of gravel with the same grain composition and relative density of 45%. The test results indicate that, when the confining pressure and shear strain amplitude exceed 300 kPa and 7×10-4, respectively, gravel with a round granular shape has a higher shear modulus compared to an angular shape. Conversely, when the shear strain amplitude exceeds 2×10-4, the damping ratio of angular gravel exceeds that of round granules.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

scholarly journals Experimental Study of Stress-Seepage Coupling Properties of Sandstone under Different Loading Paths

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-21
Author(s):  
Xi Chen ◽  
Wei Wang ◽  
Yajun Cao ◽  
Qizhi Zhu ◽  
Weiya Xu ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Pore Pressure ◽  
Complex Loading ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Compression Tests ◽  
Biot Coefficient ◽  
Cyclic Loading And Unloading ◽  
Loading And Unloading

The study on hydromechanical coupling properties of rocks is of great importance for rock engineering. It is closely related to the stability analysis of structures in rocks under seepage condition. In this study, a series of conventional triaxial tests under drained condition and hydrostatic compression tests under drained or undrained condition on sandstones were conducted. Moreover, complex cyclic loading and unloading tests were also carried out. Based on the experimental results, the following conclusions were obtained. For conventional triaxial tests, the elastic modulus, peak strength, crack initiation stress, and expansion stress increase with increased confining pressure. Pore pressure weakened the effect of the confining pressure under drained condition, which led to a decline in rock mechanical properties. It appeared that cohesion was more sensitive to pore pressure than to the internal friction angle. For complex loading and unloading cyclic tests, in deviatoric stress loading and unloading cycles, elastic modulus increased obviously in first loading stage and increased slowly in next stages. In confining pressure loading and unloading cycles, the Biot coefficient decreased first and then increased, which indicates that damage has a great impact on the Biot coefficient.

Shear Strength of a Cemented Paste Backfill Submitted to High Confining Pressure

2016 ◽  
Vol 858 ◽  
pp. 219-224 ◽  
Author(s):  
Eduardo Eiler Batista de Araújo ◽  
Dragana Simon ◽  
Fagner Alexandre Nunes de França ◽  
Osvaldo de Freitas Neto ◽  
Olavo Francisco dos Santos Jr.
Keyword(s):  
Shear Strength ◽  
Triaxial Compression ◽  
Binder Content ◽  
Cemented Paste Backfill ◽  
Compression Tests ◽  
Mining Operations ◽  
Geomechanical Properties ◽  
Confining Pressures ◽  
Paste Backfill ◽  
Curing Method

Deep mining operations require special measures in order to keep safe and economic aspects. After mine ore is extracted, voids are created and need to be filled with high-strength, low-cost materials. Cemented Paste Backfill (CPB) has recently become one of the main alternatives in filling stopes. Although numerous papers have mentioned the magnitudes of the strength of this material, its behavior under high confining pressures is still not well understood. Therefore, the purpose of this study is to increase the knowledge regarding the CPB behavior. Triaxial compression tests were performed using a Hoek Cell and Load Frame System under high confining pressures. Samples with two different binder contents were used in order to obtain the CPB strength improvement. Besides the self-weight consolidation curing method, samples were subjected to a different curing method that simulated a zero gravity condition (rotating wheel) in the first curing day to compare their mixture properties. The results suggested that both curing method and binder content have influenced the geomechanical properties of Cemented Paste Backfill. By increasing the curing time, the CPB shear strength has increased slightly, whereas specimens with higher binder content presented a significant increase in shear strength values.

Sign in / Sign up

Export Citation Format

Share Document