Energy harvesters for rotating systems: Modeling and performance analysis

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Faiz Basheer ◽  
Elmehaisi Mehaisi ◽  
Ahmed Elsergany ◽  
Ahmed ElSheikh ◽  
Mehdi Ghommem ◽  
...  
Keyword(s):  
Power Generation ◽  
Output Power ◽  
Energy Harvester ◽  
Double Pendulum ◽  
Energy Harvesters ◽  
Rotating Systems ◽  
Optimal Power ◽  
Simulation Results ◽  
And Performance ◽  
Systems Simulation

AbstractAn exclusive reliance on batteries for miniature sensors has created the need for a self-sustained energy harvester to enable permanent power. This work introduces a pendulum-based energy harvester that is capable of harnessing kinetic energy from rotating structures to generate electric power through electromagnetic transduction. A computational model of the energy harvesting device is developed on Simscape to compute, analyze and compare the power generation capacities of the single, double and Rott’s pendulum systems. Simulation results are validated against their experimental counterparts reported in the literature. Results show an increase in the output voltage in a specific range of rotational speed for all three pendulum harvesters. The double pendulum exhibits the highest power generation potential among the simulated pendulum arrangements. A parametric study revealed that increasing the damping of the harvester decreased its output power, whereas an increase in mass and length of the harvester is observed to increase the output power and shift the optimal power generation subrange.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

Lower Limb-Driven Energy Harvester: Modeling, Design, and Performance Evaluation

2016 ◽  
Vol 10 (4) ◽  
Author(s):  
Jean-Paul Martin ◽  
Michael Shepertycky ◽  
Yan-Fei Liu ◽  
Qingguo Li
Keyword(s):  
Lower Limb ◽  
Energy Harvester ◽  
Electrical Power ◽  
Peak Voltage ◽  
Daily Movement ◽  
Energy Harvesters ◽  
Portable Electronics ◽  
Proposed Model ◽  
And Performance ◽  
Parameter Values

Biomechanical energy harvesters (BMEHs) have shown that useable amounts of electricity can be generated from daily movement. Where access to an electrical power grid is limited, BMEHs are a viable alternative to accommodate energy requirements for portable electronics. In this paper, we present the detailed design and dynamic model of a lower limb-driven energy harvester that predicts the device output and the load on the user. Comparing with existing harvester models, the novelty of the proposed model is that it incorporates the energy required for useful electricity generation, stored inertial energy, and both mechanical and electrical losses within the device. The model is validated with the lower limb-driven energy harvester in 12 unique configurations with a combination of four different motor and three different electrical resistance combinations (3.5 Ω, 7 Ω, and 12 Ω). A case study shows that the device can generate between 3.6 and 15.5 W with an efficiency between 39.8% and 72.5%. The model was able to predict the harvester output peak voltage within 5.6 ± 3.2% error and the peak force it exerts on the user within 9.9 ± 3.4% error over a range of parameter values. The model will help to identify configurations to achieve a high harvester efficiency and provide a better understanding of how parameters affect both the timing and magnitude of the load felt by the user.

Sensors and energy harvesters based on (1–x)PMN-xPT piezoelectric ceramics

2019 ◽  
Vol 88 (1) ◽  
pp. 10901 ◽  
Author(s):  
Houda Lifi ◽  
Chouaib Ennawaoui ◽  
Abdelowahed Hajjaji ◽  
Samira Touhtouh ◽  
Said Laasri ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Proof Mass ◽  
Piezoelectric Ceramics ◽  
Piezoelectric Bimorph ◽  
Mechanical Vibrations ◽  
Energy Harvesters ◽  
Hot Air ◽  
Simulation Results ◽  
Piezoelectric Performance ◽  
Good Agreement

With recent advancements in energy conversion mechanisms, piezoelectric ceramics (1–x)PbMg1/3 Nb2/3Ο3-xPbTiΟ3 (1–x)PMN-xPT have demonstrated their abilities for converting mechanical vibrations into electricity. Three (1–x)PMN-xPT compositions were used in the present work with (x = 0.25, 0.31 and 0.33). The purpose of this paper is to investigate their piezoelectric performance as generators for energy harvesting applications. The energy harvester is numerically analyzed in this work. It consists of a piezoelectric bimorph clamped at one end to vibrating machinery, and a proof mass mounted on its other end. The energy harvester is also analyzed and experimental measurements of the harvested power are compared to the simulation results. A good agreement was observed between the experimental and the simulations results. According the application to exploit the vibrations of a hot air extractor, the results show that the harvested energy density of solid ceramics (1–x)PMN-xPT is 0.043 W/m2.

Fabrication and analytical modeling of transverse mode piezoelectric energy harvesters

2012 ◽  
Vol 1397 ◽  
Author(s):  
Seon-Bae Kim ◽  
Jung-Hyun Park ◽  
Seung-Hyun Kim ◽  
Hosang Ahn ◽  
H. Clyde Wikle ◽  
...  
Keyword(s):  
Output Power ◽  
Analytical Modeling ◽  
Energy Harvester ◽  
Power Conversion ◽  
Transverse Mode ◽  
Modified Model ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Interdigital Electrodes ◽  
Piezoelectric Cantilever

ABSTRACTA transverse (d33) mode piezoelectric cantilever was fabricated for energy harvesting. Various dimensions of interdigital electrodes (IDE) were deposited on a piezoelectric layer to examine the effects of electrode design on the performance of energy harvesters. Modeling was performed to calculate the output power of the devices. The estimation was based on Roundy’s analytical modeling derived for a d31 mode piezoelectric energy harvester (PEH). In order to apply the Roundy’s model to d33 mode PEH, the IDE configuration was converted to the area of top and bottom electrodes (TBE). The power conversion in d33 mode PEH was commonly estimated by the product of piezoelectric layer’s thickness and finger electrode’s length. In addition, the spacing between fingers was regarded as gap between top and bottom electrodes. However, the output power in a transverse mode PEH increases continuously with the increase of finger spacing, which does not correspond to experimental results. In this research, the dimension of IDE was converted to that of TBE using conformal mapping, and variation of power of PEH was remodeled. The modified model suggests that the maximum power in a transverse mode PEH is obtained when the finger spacing is identical with effective finger spacing. The output power then decreases when finger spacing is larger than effective finger spacing. The decrease of efficiency may result from insufficient degree of poling and increased charged defect with increasing finger spacing.

scholarly journals Design and Analysis of a Magnetically Coupled Multi-Frequency Hybrid Energy Harvester

Sensors ◽  
2019 ◽  
Vol 19 (14) ◽  
pp. 3203 ◽  
Author(s):  
Zhenlong Xu ◽  
Hong Yang ◽  
Hao Zhang ◽  
Huawei Ci ◽  
Maoying Zhou ◽  
...  
Keyword(s):  
Output Power ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Peak Output Power ◽  
Piezoelectric Energy ◽  
Operating Bandwidth ◽  
Frequency Sweep Test ◽  
Hybrid Energy Harvesting

The approach to improve the output power of piezoelectric energy harvester is one of the current research hotspots. In the case where some sources have two or more discrete vibration frequencies, this paper proposed three types of magnetically coupled multi-frequency hybrid energy harvesters (MHEHs) to capture vibration energy composed of two discrete frequencies. Electromechanical coupling models were established to analyze the magnetic forces, and to evaluate the power generation characteristics, which were verified by the experimental test. The optimal structure was selected through the comparison. With 2 m/s2 excitation acceleration, the optimal peak output power was 2.96 mW at 23.6 Hz and 4.76 mW at 32.8 Hz, respectively. The superiority of hybrid energy harvesting mechanism was demonstrated. The influences of initial center-to-center distances between two magnets and length of cantilever beam on output power were also studied. At last, the frequency sweep test was conducted. Both theoretical and experimental analyses indicated that the proposed MHEH produced more electric power over a larger operating bandwidth.

scholarly journals Topology Selection and Parametric Design of Electromagnetic Vibration Energy Harvesters by Combining FEA-in-the-Loop and Analytical Approaches

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 627 ◽  
Author(s):  
Seong-yeol Yoo ◽  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Output Power ◽  
Permanent Magnets ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Electromagnetic Energy ◽  
Vibration Energy ◽  
Maximum Output ◽  
Primary Concern ◽  
Energy Harvesters ◽  
Analytical Approaches

Electromagnetic energy harvesters have been used to capture low-frequency vibration energy of large machines such as diesel generators. The structure of an electromagnetic energy harvester is either planar or tubular. Past research efforts focus on optimally designing each structure separately. An objective comparison between the two structures is necessary in order to decide which structure is advantageous. When comparing the structures, the design variations such as magnetization patterns and the use of yokes must also be considered. In this study, extensive comparisons are made covering all possible topologies of an electromagnetic energy harvester. A bench mark harvester is defined and the parameters that produce maximum output power are identified for each topology. It is found that the tubular harvesters generally produce larger output power than the planar counterparts. The largest output power is generated by the tubular harvester with a Halbach magnetization pattern (94.7 mW). The second best is the tubular harvester with axial magnetization pattern (79.1 mW) when moving yokes are inserted between permanent magnets for flux concentration. When cost is of primary concern, the tubular harvester with axial pattern may become a best option.

scholarly journals Bandwidth Broadening of Piezoelectric Energy Harvesters Using Arrays of a Proposed Piezoelectric Cantilever Structure

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 973
Author(s):  
Marwa S. Salem ◽  
Shimaa Ahmed ◽  
Ahmed Shaker ◽  
Mohammad T. Alshammari ◽  
Kawther A. Al-Dhlan ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Piezoelectric Material ◽  
Output Power ◽  
Energy Harvester ◽  
Vibration Source ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Narrow Bandwidth ◽  
Cantilever Structure ◽  
Bandwidth Broadening

One of the most important challenges in the design of the piezoelectric energy harvester is its narrow bandwidth. Most of the input vibration sources are exposed to frequency variation during their operation. The piezoelectric energy harvester’s narrow bandwidth makes it difficult for the harvester to track the variations of the input vibration source frequency. Thus, the harvester’s output power and overall performance is expected to decline from the designed value. This current study aims to solve the problem of the piezoelectric energy harvester’s narrow bandwidth. The main objective is to achieve bandwidth broadening which is carried out by segmenting the piezoelectric material of the energy harvester into n segments; where n could be more than one. Three arrays with two, four, and six beams are shaped with two piezoelectric segments. The effect of changing the length of the piezoelectric material segment on the resonant frequency, output power, and bandwidth, as well as the frequency response is investigated. The proposed piezoelectric energy harvesters were implemented utilizing a finite element method (FEM) simulation in a MATLAB environment. The results show that increasing the number of array beams increases the output power and bandwidth. For the three-beam arrays, at n equals 2, 6 mW output power and a 9 Hz bandwidth were obtained. Moreover, the bandwidth of such arrays covered around 5% deviation from its resonant frequency. All structures were designed to operate as a steel wheel safety sensor which could be used in train tracks.

scholarly journals The Effect of Axial Displacement of Magnets in Piezoelectric Energy Harvester

2018 ◽  
Vol 7 (3.7) ◽  
pp. 95
Author(s):  
Li Wah Thong ◽  
Yu Jing Bong ◽  
Swee Leong Kok ◽  
Roszaidi Ramlan
Keyword(s):  
Frequency Spectrum ◽  
Power Output ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Operational Frequency ◽  
And Performance

The utilization of vibration energy harvesters as a substitute to batteries in wireless sensors has shown prominent interest in the literature. Various approaches have been adapted in the energy harvesters to competently harvest vibrational energy over a wider spectrum of frequencies with optimize power output.   A typical bistable piezoelectric energy harvester, where the influence of magnetic field is induced into a linear piezoelectric cantilever, is designed and analyzed in this paper. The exploitations of the magnetic force specifically creates nonlinear response and bistability in the energy harvester that extends the operational frequency spectrum for optimize performance.  Further analysis on the effects of axial spacing displacement between two repulsive magnets of the harvester, in terms of x-axis (horizontal) and z-axis (vertical) on its natural resonant frequency and performance based on the frequency response curve are investigated for realizing optimal power output. Experimental results show that by selecting the optimal axial spacing displacement, the vibration energy harvester can be designed to produce maximized output power in an improved broadband of frequency spectrum.  

scholarly journals Optimal Wireless Information and Power Transfer Using Deep Q-Network

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Yuan Xing ◽  
Haowen Pan ◽  
Bin Xu ◽  
Cristiano Tapparello ◽  
Wei Shi ◽  
...  
Keyword(s):  
Time Slot ◽  
Information Rate ◽  
High Complexity ◽  
Time Consumption ◽  
Energy Harvesters ◽  
Transmission Strategy ◽  
Wireless Transmitter ◽  
Simulation Results ◽  
Systems Simulation ◽  
Optimal Transmission Strategy

In this paper, a multiantenna wireless transmitter communicates with an information receiver while radiating RF energy to surrounding energy harvesters. The channel between the transceivers is known to the transmitter, but the channels between the transmitter and the energy harvesters are unknown to the transmitter. By designing its transmit covariance matrix, the transmitter fully charges the energy buffers of all energy harvesters in the shortest amount of time while maintaining the target information rate toward the receiver. At the beginning of each time slot, the transmitter determines the particular beam pattern to transmit with. Throughout the whole charging process, the transmitter does not estimate the energy harvesting channel vectors. Due to the high complexity of the system, we propose a novel deep Q-network algorithm to determine the optimal transmission strategy for complex systems. Simulation results show that deep Q-network is superior to the existing algorithms in terms of the time consumption to fulfill the wireless charging process.

Sign in / Sign up

Export Citation Format

Share Document