scholarly journals Device-technological simulation of the magnetosensitive sensor with integrated magnetic concentrator

2018 ◽  
pp. 15-21
Author(s):  
V. R. Stempitsky ◽  
Dao Ha
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Three Dimensional ◽  
Hall Sensor ◽  
Field Recording ◽  
Weak Magnetic Fields ◽  
Magnetic Amplifier ◽  
Hall Sensors ◽  
Magnetic Disc

The paper presents results on research and optimization on the basis of device-technological modeling of the structural and operational characteristics of the magnetosensitive sensor with a disk-shaped integrated magnetic concentrator (IMC). The high magnetic permeability of the IMC material provides a high value of the induction of the magnetic field along its edges, which leads to a significant enhancement of the applied external field. The IMC plays the role of a magnetic amplifier, and also affects the signal-to-noise and signal-to-bias ratios; the magnetic gain depends not only on the size of the IMC, but also on its shape. This research is devoted to the development of a disc-shaped magnetic concentrator integrated into the Hall sensor. The concentrator has a high magnetic flux gain and can be used in 3D magnetic field recording systems. Analysis of the geometric dimensions, deflection angle and the material of the integrated magnetic concentrator influence on the characteristics of a three-dimensional magnetic field sensor showed that the inclusion of a ferromagnetic concentrator in the Hall sensor design provides a significant (up to 10 times) increase in the magnetic flux gain. This makes it possible to use the investigated sensor designs to detect weak magnetic fields (from 0.01 µT to 2 mT). It is shown that a supermindure integrated magnetic disc-shaped concentrator with a diameter of D = 200 µm, a thickness of l = 10 µm and an angle of deflection of  = 60° provides a magnetic flux gain G = 10.81 with a maximum external magnetic field of B0 = 120 mT. The obtained results indicate the prospects of using the proposed constructive solution for the practical manufacture of three-dimensional sensors of weak magnetic fields with a magnetic sensitivity up to 3026 V/(A∙T) along the sensor surface. The type of sensor devices studied extends the scope of Hall sensors as an elemental base of medical equipment, equipment for magneto-resonant imaging (MRI), and also in instruments for geological and geodetic research.

Room Temperature Sample Scanning SQUID Microscope for Imaging the Magnetic Fields of Geological Specimens

2013 ◽  
Vol 475-476 ◽  
pp. 3-6 ◽  
Author(s):  
Qing Meng Wang ◽  
Hua Feng Qin ◽  
Qing Song Liu ◽  
Tao Song
Keyword(s):  
Magnetic Field ◽  
Low Temperature ◽  
Magnetic Fields ◽  
Liquid Helium ◽  
Quantum Interference ◽  
Three Dimensional ◽  
Input Circuit ◽  
Pickup Coil ◽  
Weak Magnetic Fields ◽  
Scanning Squid

A microscope to image weak magnetic fields using a low-temperature superconducting quantum interference device (SQUID) had developed with a liquid helium consumption rate of ~0.5L/hour. The gradient pickup coil is made by a low-temperature superconducting niobium wire with a diameter of 66 μm, which is coupled to the input circuit of the SQUID and is then enwound on the sapphire bobbin. Both of the pickup coil and the SQUID sensor are installed in a red copper cold finger, which is thermally anchored to the liquid helium evaporation platform in the vacuum space of the cryostat. To reduce the distance between the pickup coil and sample, a 100 μm thick sapphire window is nestled up to the bottom of the cryostat. A three-dimensional scanning stage platform with a 50 cm Teflon sample rack under the sapphire window had the precision of 10 μm. To test the fidelity of the new facility, the distribution of the magnetic field of basalt slice specimens was determined. Results show that the spatial resolution of the newly-designed facility is 500 μm with a gradient magnetic field sensitivity of 380fT. This opens new opportunities in examining the distribution of magnetic assemblages in samples, which bear great geological and geophysical information.

Magnetic flux transport in the photosphere of the Sun

2020 ◽  
Author(s):  
Dmitrii Baranov ◽  
Elena Vernova ◽  
Marta Tyasto ◽  
Olga Danilova
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Southern Hemisphere ◽  
Northern Hemisphere ◽  
Polar Field ◽  
The Sun ◽  
Time Diagram ◽  
Weak Magnetic Fields ◽  
The Magnetic Field

<p>On the basis of the synoptic maps of the photospheric magnetic field obtained by the National Solar Observatory Kitt Peak for 1978-2016, a latitude-time diagram of the magnetic field was built. When averaging intensity values over the heliolongitude, the magnetic field sign was taken into account. In order to consider the characteristics of the distribution of weak magnetic fields an upper limit of 5 G was set.</p><p>The latitude-time diagram clearly shows inclined bands corresponding to positive and negative polarity magnetic flows drifting towards the poles of the Sun. Two groups of flows are observed: 1. Relatively narrow bands, with alternating polarity, beginning near the equator and reaching almost the poles of the Sun. Along the time axis, the flow length of one polarity is on the order of 1-2 years; 2. short powerful flows, 3-4.5 years wide, propagating from the spot zone to the poles. These flows reach the poles simultaneously with the begin of the polar field reversal, apparently representing  the so-called “Rush to the Poles” phenomenon.</p><p>The pattern of magnetic field transport is significantly different for the northern and southern hemispheres. Alternating flows of positive and negative polarities most clearly appear in the southern hemisphere during periods of positive polarity of the southern polar field. For the northern hemisphere the picture is much less clear but for individual time intervals alternating flows of opposite polarities can be traced. The slopes of magnetic flux bands allow us to estimate the rate of meridional drift of magnetic fields, which was slightly different for the two hemispheres: V = (16±2) m/s for the southern hemisphere and V = (21±4) m/s for the northern hemisphere. The results obtained indicate that the distribution of weak magnetic fields over the surface of the Sun has a complex structure that is different for the two hemispheres and varies from cycle to cycle.</p>

Emergence of Twisted Magnetic Flux Related Sigmoidal Brightening

2000 ◽  
Vol 179 ◽  
pp. 263-264
Author(s):  
K. Sundara Raman ◽  
K. B. Ramesh ◽  
R. Selvendran ◽  
P. S. M. Aleem ◽  
K. M. Hiremath
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Ultra Violet ◽  
Active Regions ◽  
Morphological Properties ◽  
Energy Storage And Conversion ◽  
The Sun ◽  
X Rays ◽  
The Magnetic Field

Extended AbstractWe have examined the morphological properties of a sigmoid associated with an SXR (soft X-ray) flare. The sigmoid is cospatial with the EUV (extreme ultra violet) images and in the optical part lies along an S-shaped Hαfilament. The photoheliogram shows flux emergence within an existingδtype sunspot which has caused the rotation of the umbrae giving rise to the sigmoidal brightening.It is now widely accepted that flares derive their energy from the magnetic fields of the active regions and coronal levels are considered to be the flare sites. But still a satisfactory understanding of the flare processes has not been achieved because of the difficulties encountered to predict and estimate the probability of flare eruptions. The convection flows and vortices below the photosphere transport and concentrate magnetic field, which subsequently appear as active regions in the photosphere (Rust & Kumar 1994 and the references therein). Successive emergence of magnetic flux, twist the field, creating flare productive magnetic shear and has been studied by many authors (Sundara Ramanet al.1998 and the references therein). Hence, it is considered that the flare is powered by the energy stored in the twisted magnetic flux tubes (Kurokawa 1996 and the references therein). Rust & Kumar (1996) named the S-shaped bright coronal loops that appear in soft X-rays as ‘Sigmoids’ and concluded that this S-shaped distortion is due to the twist developed in the magnetic field lines. These transient sigmoidal features tell a great deal about unstable coronal magnetic fields, as these regions are more likely to be eruptive (Canfieldet al.1999). As the magnetic fields of the active regions are deep rooted in the Sun, the twist developed in the subphotospheric flux tube penetrates the photosphere and extends in to the corona. Thus, it is essentially favourable for the subphotospheric twist to unwind the twist and transmit it through the photosphere to the corona. Therefore, it becomes essential to make complete observational descriptions of a flare from the magnetic field changes that are taking place in different atmospheric levels of the Sun, to pin down the energy storage and conversion process that trigger the flare phenomena.

Tuning the Magnetic Alignment of Cellulose Nanocrystals from Perpendicular to Parallel Using Lepidocrocite Nanoparticles

2019 ◽  
Author(s):  
Valentina Guccini ◽  
Sugam Kumar ◽  
Yulia Trushkina ◽  
Gergely Nagy ◽  
Christina Schütz ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Cellulose Nanocrystals ◽  
Small Angle Neutron Scattering ◽  
Lower Amount ◽  
Magnetic Alignment ◽  
Polarized Optical Microscopy ◽  
Parallel Orientation ◽  
Weak Magnetic Fields

The magnetic alignment of cellulose nanocrystals (CNC) and lepidocrocite nanorods (LpN), pristine and in hybrid suspensions has been investigated using contrast-matched small-angle neutron scattering (SANS) under in situ magnetic fields (0 – 6.8 T) and polarized optical microscopy. The pristine CNC (diamagnetic) and pristine LpN (paramagnetic) align perpendicular and parallel to the direction of field, respectively. The alignment of both the nanoparticles in their hybrid suspensions depends on the relative amount of the two components (CNC and LpN) and strength of the applied magnetic field. In the presence of 10 wt% LpN and fields < 1.0 T, the CNC align parallel to the field. In the hybrid containing lower amount of LpN (1 wt%), the ordering of CNC is partially frustrated in all range of magnetic field. At the same time, the LpN shows both perpendicular and parallel orientation, in the presence of CNC. This study highlights that the natural perpendicular ordering of CNC can be switched to parallel by weak magnetic fields and the incorporation of paramagnetic nanoparticle as LpN, as well it gives a method to influence the orientation of LpN.<br>

scholarly journals Sensitivity of PS/CoPd Janus particles to an external magnetic field

RSC Advances ◽  
2021 ◽  
Vol 11 (28) ◽  
pp. 17051-17057
Author(s):  
Anna Eichler-Volf ◽  
Yara Alsaadawi ◽  
Fernando Vazquez Luna ◽  
Qaiser Ali Khan ◽  
Simon Stierle ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Magnetic Properties ◽  
External Magnetic Field ◽  
Magnetic Fields ◽  
Janus Particles ◽  
Weak Magnetic Fields

PS/CoPd Janus particles respond very sensitively to application of low external magnetic fields. Owing to the magnetic properties, the PS/CoPd particles may be used, for example, to sense the presence of weak magnetic fields as micro-magnetometers.

FINITE ENERGY ONE-HALF MONOPOLE SOLUTIONS

2012 ◽  
Vol 27 (40) ◽  
pp. 1250233 ◽  
Author(s):  
ROSY TEH ◽  
BAN-LOONG NG ◽  
KHAI-MING WONG
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Topological Charge ◽  
Magnetic Monopole ◽  
Magnetic Charge ◽  
Finite Energy ◽  
Spatial Infinity ◽  
Yang Mills ◽  
The Magnetic Field

We present finite energy SU(2) Yang–Mills–Higgs particles of one-half topological charge. The magnetic fields of these solutions at spatial infinity correspond to the magnetic field of a positive one-half magnetic monopole at the origin and a semi-infinite Dirac string on one-half of the z-axis carrying a magnetic flux of [Formula: see text] going into the origin. Hence the net magnetic charge is zero. The gauge potentials are singular along one-half of the z-axis, elsewhere they are regular.

A Case for Magneto Hydro Dynamics (MHD)

2001 ◽  
Author(s):  
Haim H. Bau
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Lorentz Force ◽  
Electric Fields ◽  
Biological Fluids ◽  
Fluid Volume ◽  
Chaotic Advection ◽  
Complex Flows ◽  
Electric Currents

Abstract In this paper, I review some of our work on the use of magneto hydrodynamics (MHD) for pumping, controlling, and stirring fluids in microdevices. In many applications, one operates with liquids that are at least slightly conductive such as biological fluids. By patterning electrodes inside flow conduits and subjecting these electrodes to potential differences, one can induce electric currents in the liquid. In the presence of a magnetic field, a Lorentz force is generated in a direction that is perpendicular to both the magnetic and electric fields. Since one has a great amount of freedom in patterning the electrodes, one can induce forces in various directions so as to generate complex flows including “guided” flows in virtual, wall-less channels. The magnetic flux generators can be either embedded in the device or be external. Despite their unfavorable scaling (the magnitude of the forces is proportional to the fluid volume), MHD offers many advantages such as the flexibility of applying forces in any desired direction and the ability to adjust the magnitude of the forces by adjusting either the electric and/or magnetic fields. We provide examples of (i) MHD pumps; (ii) controlled networks of conduits in which each conduit is equipped with a MHD actuator and by controlling the voltage applied to each actuator, one can direct the liquid to flow in any desired way without a need for valves; and (iii) MHD stirrers including stirrers that exhibit chaotic advection.

Theoretical Optimization of Cascading Magnets’ Structure for Oxygen Enrichment by Gradient Magnetic Fields

2009 ◽  
Author(s):  
Fengchao Li ◽  
Li Wang ◽  
Ping Wu ◽  
Shiping Zhang
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Oxygen Concentration ◽  
Uniform Magnetic Field ◽  
Oxygen Enrichment ◽  
Gradient Magnetic Field ◽  
Length Direction

Oxygen molecules are paramagnetic while nitrogen molecules are diamagnetic. In the same gradient magnetic field, the magnetizing forces on oxygen molecules are stronger than those on nitrogen molecules, which in opposite directions. The intercepting effect on oxygen molecules by gradient magnetic field can be used for oxygen enrichment from air. The structure, which is called multi-channel cascading magnets array frame in the paper, are optimized by additional yokes. By comparison of distributions of magnetic field in multi-channel array without yokes and that with yokes, the additional yokes can eliminate the differences among different magnetic spaces in multi-channel cascading magnets’ arrays and enhances the magnetic flux densities in spaces. Joining magnets together in the length direction can make the air stay longer in the ‘magnetic sieve’ and raise the oxygen concentration of air flowing out from the optimized multi-channel cascading magnets’ arrays. The inside additional yoke can used to avoid the gradient magnetic field at the joints of the magnets and get near uniform magnetic field along length direction. The optimized multi-channel cascading magnets’ array frames can effectively promote the development of oxygen enrichment from air by “magnetic sieve”.

scholarly journals The Small-Scale Photospheric Magnetic Field as an Indicator of the Dynamo

1993 ◽  
Vol 141 ◽  
pp. 143-146
Author(s):  
K. Petrovay ◽  
G. Szakály
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Magnetic Flux ◽  
Observational Data ◽  
Convective Zone ◽  
Small Scale ◽  
Dynamo Theory ◽  
Flux Tubes ◽  
Magnetic Flux Tubes ◽  
Surface Fields

AbstractThe presently widely accepted view that the solar dynamo operates near the base of the convective zone makes it difficult to relate the magnetic fields observed in the solar atmosphere to the fields in the dynamo layer. The large amount of observational data concerning photospheric magnetic fields could in principle be used to impose constraints on dynamo theory, but in order to infer these constraints the above mentioned “missing link” between the dynamo and surface fields should be found. This paper proposes such a link by modeling the passive vertical transport of thin magnetic flux tubes through the convective zone.

scholarly journals Magnetized Black Holes: Ionized Keplerian Disks and Acceleration of Ultra-High Energy Particles

Proceedings ◽  
2019 ◽  
Vol 17 (1) ◽  
pp. 13 ◽  
Author(s):  
Zdeněk Stuchlík ◽  
Martin Kološ ◽  
Arman Tursunov
Keyword(s):  
Magnetic Field ◽  
Black Holes ◽  
Magnetic Fields ◽  
High Energy ◽  
Weak Magnetic Fields ◽  
Motion Transformation ◽  
Penrose Process ◽  
Field Lines ◽  
High Energy Particles ◽  
Quasiperiodic Oscillations

Properties of charged particle motion in the field of magnetized black holes (BHs) imply four possible regimes of behavior of ionized Keplerian disks: survival in regular epicyclic motion, transformation into chaotic toroidal state, destruction due to fall into the BHs, destruction due to escape along magnetic field lines (escape to infinity for disks orbiting Kerr BHs). The regime of the epicyclic motion influenced by very weak magnetic fields can be related to the observed high-frequency quasiperiodic oscillations. In the case of very strong magnetic fields particles escaping to infinity could form UHECR due to extremely efficient magnetic Penrose process – protons with energy E > 10 21 eV can be accelerated by supermassive black holes with M ∼ 10 10 M ⊙ immersed in magnetic field with B ∼ 10 4 Gs.

Sign in / Sign up

Export Citation Format

Share Document