Effect of β–Si3N4 seed crystal on the microstructure and mechanical properties of sintered reaction-bonded silicon nitride

1999 ◽  
Vol 14 (1) ◽  
pp. 178-184 ◽  
Author(s):  
Soo Young Lee ◽  
K. Amoako-Appiagyei ◽  
Hai Doo Kim
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
High Strength ◽  
Considerable Improvement ◽  
Seed Crystal ◽  
Bimodal Microstructure ◽  
Seed Crystals ◽  
Before And After ◽  
Gas Pressure Sintering

β–Si3N4 seed crystal has been synthesized from α–Si3N4 powder. Reaction-bonded Si3N4/SiC composite has been fabricated with β–Si3N4 seed crystals. The nitridation behavior and the changes in mechanical properties resulting from the addition of seed crystals were studied before and after gas pressure sintering. Addition of seeds showed a considerable improvement in the nitridation, resulting in increase in fracture strength of the composite. Highly nitrided reaction-bonded Si3N4 (RBSN) as a result of the addition of seed crystals gave rise to high strength of composite after postsintering. Fracture toughness of the seeded Si3N4 was also improved up to 35% compared to the baseline Si3N4. Micrographs showed that the seeded Si3N4 developed a bimodal microstructure which resulted in an improvement in fracture toughness.

scholarly journals Determination of fracture toughness and elastic module in materials based silicon nitride

2019 ◽  
Vol 20 (4) ◽  
pp. 1-13
Author(s):  
Edwuin Jesus Carrasquero Rodriguez ◽  
Jaime Moises Minchala Marquino ◽  
Byron Ramiro Romero Romero ◽  
Luis Marcelo Lopez Lopez ◽  
Jorge Isaac Fajardo Seminario
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Rare Earth ◽  
Silicon Nitride ◽  
High Strength ◽  
Mechanical Resistance ◽  
Elastic Module ◽  
Structural Applications ◽  
The Matrix ◽  
Materials Used

The knowledge of the mechanical properties of any material subjected to loads is necessary for its use in structural applications. Silicon nitride (Si3N4) ceramics are well-known materials used in engineering applications due to their outstanding combination of high strength and fracture toughness. The most studied mechanical properties of Si3N4 are hardness, fracture toughness and mechanical resistance. Recent advances in the production processes that incorporate high purity rare earth elements as sintering additives have improved these mechanical properties. Using Vickers indentation method, the elastic module and fracture toughness of Si3N4 based materials modified with La2O3, Y2O3 and Al2O3 were determined as a function of the cracking system type that prevails under the effect of load. The results indicate that adding rare earth to the matrix increased the fracture toughness the Si3N4 base ceramic Samples containing La2O3+Y2O3 showed higher values of fracture toughness than the ones with Al2O3+La2O3, regardless of the equation used in the calculations. Meanwhile the elastic module decrease approximately 100 GPa for both types of nitrides by the effect of the temperature.

CARLSON ALLOY C600 and C600 ESR

Alloy Digest ◽  
1994 ◽  
Vol 43 (11) ◽  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Cold Working ◽  
Elevated Temperatures ◽  
High Strength ◽  
Heat Treating ◽  
Solid Solution Alloy ◽  
Resistance To Oxidation ◽  
Good Workability

Abstract CARLSON ALLOYS C600 AND C600 ESR have excellent mechanical properties from sub-zero to elevated temperatures with excellent resistance to oxidation at high temperatures. It is a solid-solution alloy that can be hardened only by cold working. High strength at temperature is combined with good workability. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: Ni-470. Producer or source: G.O. Carlson Inc.

Influence of additive composition on thermal and mechanical properties of β–Si3N4 ceramics

2004 ◽  
Vol 19 (11) ◽  
pp. 3270-3278 ◽  
Author(s):  
Xinwen Zhu ◽  
Hiroyuki Hayashi ◽  
You Zhou ◽  
Kiyoshi Hirao
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Fracture Toughness ◽  
Nitrogen Pressure ◽  
High Fracture Toughness ◽  
Oxygen Impurity ◽  
Thermal And Mechanical Properties ◽  
High Fracture ◽  
Doped Materials ◽  
Gas Pressure Sintering

Dense β–Si3N4 ceramics were fabricated from α–Si3N4 raw powder by gas-pressure sintering at 1900 °C for 12 h under a nitrogen pressure of 1 MPa, using four different kinds of additive compositions: Yb2O3–MgO, Yb2O3–MgSiN2, Y2O3–MgO, and Y2O3–MgSiN2. The effects of additive composition on the microstructure and thermal and mechanical properties of β–Si3N4 ceramics were investigated. It was found that the replacement of Yb2O3 by Y2O3 has no significant effect on the thermal conductivity and fracture toughness, but the replacement of MgO by MgSiN2 leads to an increase in thermal conductivity from 97 to 113 Wm-1K-1and fracture toughness from 8 to 10 MPa m1/2, respectively. The enhanced thermal conductivity of the MgSiN2-doped materials is attributed to the purification of β–Si3N4 grain and increase of Si3N4–Si3N4 contiguity, resulting from the enhanced growth of large elongated grains. The improved fracture toughness of the MgSiN2-doped materials is attributed to the increase of grain size and fraction of large elongated grains. However, the same thermal conductivity between the Yb2O3- and Y2O3-doped materials is related to not only their similar microstructures, but also the similar abilities of removing oxygen impurity in Si3N4 lattice between Yb2O3 and Y2O3. The same fracture toughness between the Yb2O3- and Y2O3-doped materials is consistent with their similar microstructures. This work implies that MgSiN2 is an effective sintering aid for developing not only high thermal conductivity (>110 Wm−1K−1) but also high fracture toughness (>10 MPa m1/2) of Si3N4 ceramics.

Effects of Sintering Additives on the Microstructure and Mechanical Properties of Silicon Nitride Ceramics by GPS

2010 ◽  
Vol 105-106 ◽  
pp. 27-30 ◽  
Author(s):  
Wei Ru Zhang ◽  
Feng Sun ◽  
Ting Yan Tian ◽  
Xiang Hong Teng ◽  
Min Chao Ru ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Transformation ◽  
Silicon Nitride ◽  
Porous Silicon ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Additives ◽  
Microstructure And Mechanical Properties ◽  
Nitride Ceramics

Silicon nitride ceramics were prepared by gas pressure sintering (GPS) with different sintering additives, including La2O3, Sm2O3 and Al2O3. Effect of sintering additives on the phase-transformation, microstructure and mechanical properties of porous silicon nitride ceramics was investigated. The results show that the reaction of sintering additives each other and with SiO2 had key effects on the phase-transformation, grain growing and grain boundaries. With 9MPa N2 atmosphere pressure, holding 1h at 1850°C, adding 10wt% one of the La2O3, Sm2O3, Al2O3, porous silicon nitride was prepared and the relative density was 78%, 72%, 85% respectively. The flexural strength was less than 500MPa, and the fracture toughness was less than 4.8MPam1/2. Dropping compounds sintering additives, such as La2O3+Al2O3, Sm2O3+Al2O3 effectively improves the sintering and mechanical properties. The relative density was 99.2% and 98.7% with 10wt% compounds sintering additives. The grain ratio of length to diameter was up to 1:8. The flexural strength was more than 900MPa, and the fracture toughness was more than 8.9MPam1/2.

scholarly journals Synthesis of "in situ" reinforced silicon nitride composites

2004 ◽  
Vol 69 (1) ◽  
pp. 59-67 ◽  
Author(s):  
Aleksandra Vuckovic ◽  
Snezana Boskovic ◽  
Ljiljana Zivkovic
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
Pressureless Sintering ◽  
Sintering Additives ◽  
Sintering Time

The objective of this work was to investigate the effect of two different sintering additives (CeO2 and Y2O3 + Al2O3), sintering time and amount of ?-Si3N4 seeds on the densification, mechanical properties and microstructure of self-reinforced Si3N4 based composites obtained by pressureless sintering. Preparation of ?-Si3N4 seeds, also obtained by a pressureless sintering procedure, is described. Samples without seeds were prepared for comparison. The results imply that self-reinforced silicon nitride based composites with densities close to the theoretical values and with fracture toughness of 9.3MPa m1/2 can be obtained using a presureless sintering procedure.

Thermal Conductivity of Si₃N₄ Ceramics Fabricated From Carbothermal-reduction-derived Powder

2021 ◽  
Author(s):  
Yuelong Wang ◽  
Xingyu Li ◽  
Haoyang Wu ◽  
Baorui Jia ◽  
Deyin Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Fracture Toughness ◽  
Grain Size ◽  
Flexural Strength ◽  
Grain Boundaries ◽  
Carbothermal Reduction ◽  
Secondary Phase ◽  
Gas Pressure ◽  
Gas Pressure Sintering

Abstract Si3N4-based ceramic (Si3N4-5wt%Y2O3-3wt%MgO) was obtained from carbothermal-reduction-derived powder combined with gas pressure sintering. The phase, microstructure, thermal conductivity and mechanical properties of Si3N4 ceramics were comprehensively analyzed. Dense Si3N4 ceramic with uniform grain size was obtained after sintering at 1900°C for 7 h under a N2 pressure of 1.2 MPa. The secondary phase consisted of Y4Si2O7N2 and Y2Si3O3N4 was found to gather around triangular grain boundaries. The thermal conductivity, flexural strength, hardness and fracture toughness of the Si3N4 ceramics were 95.7 W·m-1·k-1, 715 MPa, 17.2 GPa and 7.2 MPa·m1/2, respectively. The results were compared with product derived from commercial powder, the improvement of thermal conductivity (~8.3%) and fracture toughness (~4.3%) demonstrating the superiority of Si3N4 ceramics prepared from carbothermal-reduction-derived powder.

scholarly journals Silicon Nitride-Based Composites with the Addition of CNTs—A Review of Recent Progress, Challenges, and Future Prospects

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2799
Author(s):  
Awais Qadir ◽  
Péter Pinke ◽  
Ján Dusza
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
Silicon Nitride ◽  
Wear Rate ◽  
Recent Progress ◽  
Bending Strength ◽  
Microstructure Development ◽  
Future Prospects ◽  
Microstructure Characteristics

In this overview, the results published to date concerning the development, processing, microstructure characteristics, and properties of silicon nitride/carbon nanotube (Si3N4 + CNTs) composites are summarized. The influence of the different processing routes on the microstructure development of the Si3N4 + CNTs is discussed. The effects of the CNTs addition on the mechanical properties—hardness, bending strength and fracture toughness—and tribological characteristics—wear rate and coefficient of friction—are summarized. The characteristic defects, fracture origins, toughening and damage mechanisms occurring during the testing are described. The influence of the CNTs’ addition on the thermal and functional properties of the composites is discussed as well. New trends in the development of these composites with significant potential for future applications are outlined.

Effect of FSP on Strength and Fracture Toughness of Aluminium Alloy 7000

2018 ◽  
Vol 877 ◽  
pp. 20-25
Author(s):  
P.K. Mandal
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Aluminium Alloy ◽  
Axial Force ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Measurement ◽  
Traverse Speed ◽  
Age Hardening ◽  
Friction Stir

The cast Al-Zn-Mg 7000 alloy has become one of the most potential structural materials in many engineering fields such as aircraft body, automotive casting due to their high strength to weight ratio, strong age hardening ability, competitive weight savings, attractive mechanical properties and improvement of thermal properties. The cast aluminium alloy has been modified of surface layer through a solid-state technique is called friction stir process (FSP). But basic principle has been followed by friction stir welding (FSW). This process can be used to locally refine microstructures and eliminate casting defects in selected locations, where mechanical properties improvements can enhance component performance and service life. However, some specified process parameters have adopted during experimental works. Those parameters are tool rotation speed (720 rpm), plate traverse speed (80 mm/min), axial force (15 kN), and tool design (i.e., pin height 3.5 mm and pin diameter 3.0 mm), respectively. The main mechanism behind this process likely to axial force and frictional force acting between the tool shoulder and workpiece results in intense heat generation and plastically soften the process material. The specified ratio of rotational speed (720 rpm) to traverse speed (80 mm/min) is considered 9 as low heat input during FSP and its entails low Zn vaporization problem results as higher fracture toughness of aluminium alloy. It is well known that the stirred zone (SZ) consists of refine equiaxed grains produced due to dynamic recrystallization. FSP has been proven to innovatively enhancing of various properties such as formability, hardness and fracture toughness (32.60 MPa√m). The hardness and fracture toughness of double passes AC+FSP aluminium alloy had been investigated by performing Vicker’s hardness measurement and fracture toughness (KIC)(ASTM E-399 standard) tests. Detailed observations with optical microscopy, Vicker’s hardness measurement, SEM, TEM, and DTA analysis have conducted to analyse microstructure and fracture surfaces of double passes FSP aluminium alloy.

Mechanical Properties of a Novel High-Strength Aluminum-Lithium Alloy

2011 ◽  
Vol 689 ◽  
pp. 385-389 ◽  
Author(s):  
Zhi Shan Yuan ◽  
Zheng Lu ◽  
You Hua Xie ◽  
Xiu Liang Wu ◽  
Sheng Long Dai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Test ◽  
High Strength ◽  
Heat Treatments ◽  
Fracture Toughness Test ◽  
Aluminum Lithium Alloy ◽  
Toughness Test ◽  
Aluminum Lithium ◽  
Strength And Ductility

As a heat treatable aluminum alloy to be used in T6 and T8 temper, belongs to Al-Cu-Li system, a novel high-strength aluminum-lithium alloy 2A97 was developed. In order to improve the relationships of strength and ductility and fracture toughness, and to urge the applications in the aeronautical and aerospace industries, the effects of normal heat treatments and thermomechanical heat treatments on the mechanical properties and fracture toughness were investigated by Transmission Electron Microscope(TEM), Scanning Electronic Microscope (SEM), tensile test, and fracture toughness test. The results show that for the alloy aged at 135 °C for 24 h after quenching and 4 percent plastic deformation, its microstructures are strengthened by strain hardening and precipitation hardening, consisting of fine T1phase, θ″/θ′ phase and δ′ phase densely and homogeneously distributed in the matrix. It yields optimum relationship of strength and ductility, fracture toughness, its σ0.2, σband δ5are 454 MPa, 536 MPa, and 11.8%, respectively. It yields 43.5 MPa·m1/2of Kqvalues higher than that of 42.5 MPa·m1/2 in T6 temper. The fracture morphologies of impact tensile samples of fracture toughness test and normal tensile test were observed, indicating the dominance of intergranular failure and subintergranular failure with some dimples and trangranular failure.

Sign in / Sign up

Export Citation Format

Share Document